Question about 2000 Dodge Intrepid

Open Question

Open ccd bus line,fail tcm - 2000 Dodge Intrepid

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 87 Answers

SOURCE: BBECM fault-no CCD from TCM

Your trans control module is more than likley the problem due to the fail tcm

Posted on Mar 28, 2009

dttech
  • 4803 Answers

SOURCE: codesFEILED ECM-TCM

There are a couple of possibilities here. That type of code can set due to low battery voltage at one or more of your computer modules. The integrity and codition of the battery and charging system should be verifeid FIRST. If you have had to jump-start your vehicle (for whatever reason) this could be the cause of this code. If this is the reason for it, all that needs to be done is to repair whatever caused the low battery condition and clear the code.

Otherwise, there is a problem in the data circuits between the modules in your vehicle. If there has not been a low or shorted battery condition, then there is most likely an open circuit in your CCD BUS (network circuit wires) You will have to diagnose the problem with a scan tool that has the capabilities to access the ENTIRE computer network in your vehicle to determine where the problem is actually located. Possible causes are broken wires, or loose or corroded connectors, or a failed computer module. Please note that computer module failures are relatively RARE. I do not recommend replacing ANY computer module without FIRST performing proper diagnostics to PROVE that a loss of communication is the fault of the module itself and not the circuits leading to it.

Posted on Nov 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is my radiator over heating? Replaced , side cracked, replaced thermostat. Still over heat.


DId you run engine with rad cap off for a long time while refilling radiator and also, have heater turned on while doing it?

Oct 02, 2014 | 1999 Plymouth Voyager

1 Answer

What is a aa1-Open CCD bus line TCM for dodge carevan 1998


Open wire to the computer. Somewhere. Sorry I can't be more helpful. Sounds like wire #aa1 is open (cut or disconnected) on the Common Computer Data Bus line Transmission or Temp. Control Module.

Aug 28, 2014 | Cars & Trucks

1 Answer

1197 Doge Caravan 3.8 No CCD message from TCM Cause Open bus line. Where is this located?


No idea you would need to ask one of these modern mechanics with a laptop under their arm i too old to even understand the abbreviations ,but at least i can centralise the self park on the wipers and know how to change down the gears by double the clutch .

Aug 23, 2013 | 1998 Plymouth Grand Voyager

1 Answer

Open ccd bus line on a 1999 grand caravan


That's normal for Chrysler minivans. Clear the code and don't worry about it unless it happens again.

Aug 09, 2012 | 1999 Dodge Grand Caravan

1 Answer

What is p1698 and how do i fix it?



Trouble Co Power Control Module A module or computer used in an electronic transmission to aid in control of the shift solenoidsde: P1698

No CCD Messages Received From The TCM
Possible Causes:


CCD data Bus circuit is open, shorted to ground or to power TCM or the PCM has failed

Jun 03, 2012 | 2002 Chrysler Town & Country

1 Answer

I have a 2004 Chrysler 300m with a 3.5l engine and getting a 0871 and 0700 code.


Please don't forget to rate!


Trouble Code: P0871 (3.5L V6 VIN G Auto)
A/T O/D Pressure Switch Circuit Malfunction


Trouble Code Conditions:
Engine started; vehicle driven in a forward gear, and the PCM detected that the O/D Pressure Switch circuit indicated open or closed at the wrong time.

Possible Causes:

  • Related DTCs may be present
  • O/D pressure is incorrect, or internal transmission faults exist
  • O/D pressure switch circuit is open, shorted to ground or power
  • O/D pressure switch is damaged or it has failed
  • TCM relay power circuit to O/D switch is open (loss of B+)
  • Intermittent wiring or connector problems exist
  • PCM or TCM has failed


Trouble Code: P0700 (3.5L V6 VIN G Auto)
Automatic Transmission Control System Malfunction


Trouble Code Conditions:
Ignition on or engine started. The PCM received a message over the CCD Bus from the Transmission Control Module (TCM) that it had detected a problem and set a trouble code in memory.

Possible Causes:

  • The presence of this code means the TCM detected a problem
  • TCM related Sensor has solenoid is damaged or has failed
  • This code is for information only - check for other TCM codes
  • TCM or PCM has failed

May 08, 2011 | 2004 Chrysler 300M

3 Answers

Can you please tell what are these codes for 1997 dodge caravan sport.p1698 and p1495.


P1698 Chrysler

ECM fault-No CCD message from TCM
- Failed ECM

Probable Cause[s]

  1. Open CCD bus line
  2. Failed TCM
P1495 Chrysler

EVAP leak detection pump solenoid circuit condition
- ECM detected the pump solenoid did not change status when activated

Probable Cause[s]

  1. Pump solenoid defective
  2. Open or shorted circuit condition
  3. ECM Defective

Feb 08, 2011 | 1997 Dodge Caravan

1 Answer

Code p1698 town & country 96 fail the emission test


p1698 code=No CCD message from TCM or No Transmission Bus Messages
It means the person's computer could not connect with yours.it's possible it was his problem if your not having any issues


Dec 04, 2009 | 1996 Chrysler Town & Country

2 Answers

Wont start my odometer blinks and says no bus


From the official Durango shop manual......(abbreviated)

Self Diagnosis Test

Vehicle key position is OFF ,or able to pull key out.
Hold in the trip odometer button (dont release yet)
Turn key to the ON position (one notch), but DON'T try to start the engine
Continue holding the trip button for about 10-12 seconds until CHEC appears in the odometer display
Release the trip button.
Series of three digit numeric failure codes may appear.
If no failure message appears, the self diagnostic test will proceed as described in step 6


Code Chart

110- cluster CPU,RAM,EEPROm failure, replace cluster

900-CCD data bus not operational, check CCD data bus connections at cluster, check the cluster fuses,check the CCD data bus bias, cehck the CCD data bus voltage, check the CCD data bus terminations.

920-cluster is not recieving a vehicle speed message from the PCM, check PCM software level and reflash if required, use the ($2500+) DRBIII scan tool to verify the vehicle speed message is being sent by the PCM

921-the cluster is not recieveing a distance pulse message from PCM,check PCM software level and reflash if required, use the ($2500+) DRBIII scan tool to verify the distance pulse message is being sent by the PCM

940-the cluster is not recieving an airbag lamp-on message from the ACM, check the CCD data bus connections at the ACM, check the ACM fuse.

950-cluster not recieving an ABS lamp-on message from the CAB, check CCD data bus connections at the ACM, check the ACM fuse.

960- clsuter not recieving a PRND21 message from the TCM, check the CCD data bus connections at the TCM, check the TCM fuse.

999-An error has been discovered, record the failure message, depress the trip odometer reset button to continue the Self-Diagnostic Test

Step 6
Instrument cluster will test each segment of the odometer (all first, then each one seperately)

Step 7
Bulb test

Step 8
Gauge test

Step 9
test completed

The instrument cluster will return to normal operation at the completion of test, if ignition switch turned off, or a vehicle speed message indicating movement recieved from the PCM on the CCD data bus.

Hope that help you or anyone else in future.

Aug 10, 2008 | 2000 Dodge Durango

Not finding what you are looking for?
2000 Dodge Intrepid Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...