Question about 1985 Nissan Pickup

1 Answer

I have installed a used carb.,new cap,rotor,plugs,fuel control relay,used dist.The same problem still exists.Under 1000 rpm the vehicle sometimes stalls.It fires back up,sometimes with a backfire and seems tight.1985 720 2.4l

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You blew your head gasket, water leaking into cylinder, when you let the car sit, it cools water seeps into cylinder. you drive it around it warms up, water evaporates, the metal expands due to heat. water stops leaking into cylinder and car feels to run normal again.

Posted on Apr 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

1995 chevy full size van, cranks wont start Replaced fuel pump, rotor, dist. started once but now why does it crank but won't start?


It could be a bad fuel pump relay. Or the relay is not getting the proper signal from the pcm to turn on. If a new relay doesn't fix, have the relay's circuit checked.

Oct 04, 2014 | Chevrolet Cars & Trucks

1 Answer

Not getting fire to plug wires. I have replaced coil pack, module, dist pickup,and cap. I have tested and have fire to dist but nothing coming out. This is an 86 2.8 comanche 4x4 w/ 4 barrel Holley carb...


You have spark on the coil wire but not coming from the cap. You replaced the cap right. Did you replace the rotor too. Sometimes the rotor burn in the center and the spark goes right thru it in to the distributor shaft.

Aug 11, 2010 | 1986 Jeep Comanche

2 Answers

Will not start


Did you install the correct plugs, and did you check the gap? Also check all wires again to make sure nothing was pulled off, or loosened by accident.

Feb 07, 2010 | 1993 Lexus Ls 400

1 Answer

1990 K5 Blazer DIED(Electrical?)?


There may be no injector pulse if the computor does not see a RPM signal.
There will be no spark if the ignition module does not see a dist pulse from the dist pickup.......a RPM signal.
Because you do not have both ......I would suggest to check/change the dist pick up.
Follow the wires from the ignition module inside the dist to the pickup which is also inside the dist.
If it is just a bad dist pickup....keep all your old parts as good spares.
Also...is the dist turning? to provide a RPM signal?
You will have to remove the dist to change the pick-up.....mark your timing locations......"rotor position" and "dist body location"before removal.
A quick test before installing the "repaired dist" .....plug it in the the truck wiring and turn on the key....DO NOT CRANK THE ENGINE OR YOU WILL LOSE YOUR DIST ROTOR CORRECT POSITION......as you spin the dist by hand .....the injectors should spray.

Aug 23, 2009 | 1989 Chevrolet S-10 Blazer

1 Answer

Won't start 96 k1500


fuel problem or timing problem i had same problem on 94 aerostar found out the dist. was bad and timing off by 20* bought used dist. adjusted timing runs beautiful

Mar 23, 2009 | 1996 Chevrolet K1500

2 Answers

89 crx has power but wont start.


replace the ignition control module,I recommend a new one,if you order a rebuilt dist.it comes with a used one that only passed cold temp bench test they usually have problems once the car warms up. so get a new one!good luch let me know if you need more info have a good day DB

Feb 14, 2009 | 1989 Honda CRX

5 Answers

Ford 351W


I agree, jumped timing. Check to make sure the dist is tight. Than check for tdc on the #1 cylinder. When the #1 cyl is TDC the rotor should be pointing to that wire on the cap. Take the cap off while checking. Also is easier to turn motor by hand without plugs in motor.

Jul 29, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14251 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...