Question about 1994 Nissan Sentra 4-Door

Open Question

1996 nissan sentra timing and cam alinement

There are three cam gears one is the main from the crankshaft and two are the cams intake ane exhaust. what are the alinements

Posted by on

  • Anonymous Aug 18, 2008

    need to know the camshaft timing mark for the ga15 i set it at exhaust 12 o clock and intake 9 o clock

×

6 Suggested Answers

chiquititas
  • 1010 Answers

SOURCE: 1996 nissan sentra

Find the big hose that comes out of the top of the radiator and follow it to the engine and that is where the thermostat is located. My advice is to be sure to get a factory thermostat and rubber gasket as it makes installation much easier. I have done it both ways and the factory one is easier to install.

Posted on Jun 29, 2008

leetamara
  • 702 Answers

SOURCE: i need to know how

Do you have the 2.4 Quad 4 engine? This makes a difference. Let me know so I can give you the proper sequence.

Posted on Jul 20, 2008

  • 14036 Answers

SOURCE: timing setting for 94 saturn sL 1 ,can not find

you need a haynes repair manual.

Posted on Apr 02, 2009

  • 4 Answers

SOURCE: 2004 nissan sentra starts the stops. acts like

check your ecm connection

Posted on May 08, 2009

michigan man
  • 3533 Answers

SOURCE: timing mark

give this website a try to see if they have the information you need www.alldatadiy.com

Posted on May 20, 2009

  • 98 Answers

SOURCE: dashboard lights do not work on my 1996 nissan

check fuses

Posted on Jun 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need timing marks for 1993 1.6 Toyota Corola camshafts


If its the 1.6litre 4afe. Turn the crankshaft to TDC, ie. Tiny slit on the crank pulley should be straight underneath the 0deg mark. The cams, intake cam is driven off the exhaust cam by means of two gears. Installation marks. They have 4 holes in front of the gears. Front being closest to timing belt. Upon installation one hole in each gear should face upwards and the other holes should face each other between the gears. On the exhaust cam pulley there is a hole drilled through it, ie. timing mark. It should face up. Directly inline with the grove in the first cam cap. If you have 1.6litre 4age engine. Between cam gears and cylinder head there should be a plate. groves in cam gears should face the groves in the the plate.

Oct 19, 2014 | 1993 Toyota Corolla

1 Answer

Engine torque settings


Commonly Asked Torque Specs in foot pounds
The main bolts have a torque of 76 lb.-feet and the cylinder head bolts have 62 lb.-feet of torque. The cylinder head studs have 70 foot-lbs of torque, the cam timing gear have lb.-feet of torque, and the cam bearing bolt has 14 lb.-feet of torque.

Crankshaft Torque Specs
  • The stock rod bolts have 46 lb.-feet of torque and the ARP rod bolts have 50 lb.-feet of torque. The crankshaft pulley has 116 lb.-feet of torque, while the flywheel has 80 lb.-feet of torque.


Other Torque Specs
  • The intake manifold and exhaust manifold have 33 lb.-feet of torque each and the oil pan bolts have 9 lb.-feet of torque. The cam timing gear has 58 lb.-feet of torque and the cam bearing bolt has 14 lb.-feet of torque. One set of timing cover bolts have 9 lb.-feet of torque and another set has 29 lb.-feet of torque

Nov 07, 2012 | 1994 Toyota Corolla

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

1 Answer

I have a blown head gasket. i need to know if i need to remove the air intake to take off the head to get to the gasket. thank you


yes, air intake, intake manifold and exhaust manifold. This is not a job for a novice. If engine has overhead cam, then cam chain/belt must also be removed. Rocker arms must be loosened to allow valves to close. Note position of timing gear in case cam rotates while chain/belt is off. Camshaft must be properly timed to the crankshaft on reassembly.
Head should be checked for warping and cracks. Follow torque instructions carefully when reinstalling the head.

Aug 23, 2010 | 1990 Chevrolet Cavalier

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000


To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

1 Answer

How do you set the timing on a 94 Nissan Sentra?


There is 3 marks on the timing chain, 2 are exactly 16 links apart and the other is 22 from either of the 2. The engine should be at top dead center. Line the 2 (16 apart) marks with marks on your cam gears and the 3rd with your crank gear. Torque cam bearings to 100 inch lbs.

Feb 03, 2010 | 1994 Nissan Sentra 4-Door

1 Answer

Need to know how to install my timing belt back on my 2005 pt cruiser the timing of the belt on the camshaft and the crankshaft


EXHAUST CAM WILL HAVE A NOCH ALIN AT 3 OCLOCK THE INTAKE ALIN AT 9 OCLOCK BOTH MARK ON THE CAM SPORKET MARK MEET EACH ANOTHER, THE CRANKSHAFT GEAR WILL HAVE A NOCH THERE WILL BE A MARK AT ABOUT 12 OCLOCK ALIN CRANK GEAR TO THAT MARK.

Nov 04, 2009 | 2005 Chrysler PT Cruiser

2 Answers

Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin


these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

May 12, 2009 | 1999 Daewoo Nubira

1 Answer

Timing gear set


That is a dual overhead cam engine. On the oil pump housing there is an arrow cast into the housing. Line the arrow on the crank pulley up with the arrow on the oil pump housing, that will set your crankshaft in time. Next you'll need to set your camshafts. This is the procedure for doing that......the exhaust cam gear (nearest the firewall) has markings on it that say "2.4L" on one side and "up^" on the other side. On the left side of the gear is a notch on the tooth. This notch MUST be set at 3:30 and the intake cam at EXACTLY 9:00. Once you've installed the timing belt and you rotate the tensioner to "tighten", the offsetting of the exhaust cam will match up with the intake cam. And presto!!! your timing is now set. Make sure you turn the crank sprocket TWO complete revolutions and verify your timing marks.

Chris

Nov 08, 2008 | 2000 Dodge Caravan

Not finding what you are looking for?
1994 Nissan Sentra 4-Door Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...