Question about 1995 Chevrolet S-10 CA Edition

Open Question

95, s10 pickup, changed plugs wires started it up now having trouble code PO503 not shifting right idles fine revs nicely

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 352 Answers

SOURCE: Transmission Problem

Its flood a tranny sensor causing a circuit fault, rain water conducts electricity. Locate this/these sensors and coat them with a sealing agent, your local auto parts store will have the stuff you need. No water, no short.

anaanymous

Posted on Oct 11, 2008

  • 95 Answers

SOURCE: haveing trouble getting to my heater core on 95

The entire dash has to come part way or all of the way out. to gain access.

Posted on Oct 17, 2009

  • 474 Answers

SOURCE: 87 chevy 350 fuel injected pickup wont run smoothly

sounds like your egr valve is gummed up or bad. this is located behind the throttle body and has a single vaccum tube connected to it. if the diafram is still good you can remove it and clean it with WD 40 until the plunger works smooth

Posted on Nov 08, 2009

  • 61 Answers

SOURCE: i have a 95' 1500 chevy pickup ... Cluster issue

sounds like you may have a problem with your speed o gear in trans.

Posted on Dec 13, 2009

  • 1 Answer

SOURCE: My 1999 chevy s10 runs rough at idle

I have a 94 s-10 blazer that runs at idel speeds but boggs down when flooring it and will have trouble starting back up also has a slow crank over when starting even with jumpers on it a lot of new stuff was fixed to try to solve the problem but nothing things replaced was as followed.

spider injecters 3 times pep boys warrented them so.
egr valve
map air flow sensor
plugs & wires
sensor under the cap & the cap
2 more sensors up front of the motor that i can not remember
fuel filter &pump so help me out please.

Posted on Jan 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

89 chevy s10 misfires and sputters when i give it gas, dies when i stop. Sometimes it runs fine, but recently it's just been bad. When i rev the engine it can stabilize the idle, but usually die


check fuel pump pressure- fuel filter --air filter --egr valve if carboned up clean or replace and cat converter feel the exhaust if feels restricted may be clogging up

Mar 30, 2013 | Chevrolet Blazer Cars & Trucks

2 Answers

Grand prix 02 cuts out when try to drive but idle fines


This vwehicle has a rev limiter, if your trying to rev it up in neutral it will cut out at 2grand.

Feb 28, 2013 | 2002 Pontiac Grand Prix

1 Answer

Motor skipps during acceleration on 1998 s10 pick up 4.3 v6


a bad plug wire will break down when accelerating but act ok when idling change plugs and wires

Dec 27, 2012 | 1998 Chevrolet S-10 Pickup

1 Answer

Rough idle while slowing down


Any codes? Dirty throttle body.Fuel filter.Air filter.

May 01, 2017 | 1989 Chevrolet C1500

1 Answer

F100 pickup stalls out when coming to a stop. It restarts and drives fine. I've rebuilt the carb., changed the fuel filters and line, and replaced the gas tank and sending unit. What am I missing or do i...


It might be the float but if you don't have any trouble getting the truck up to speed then it's likely fine. The trouble is more likely to be in the idle circuit. The curb idle should be 500 to 750 RPM depending on if it's standard or automatic ( higher for auto). If that's okay then you may have to play with the idle screws. Turn them both the same amount, 1/4 turn at a time. Turn them once and then rev the engine 2 or 3 times and let it idle down suddenly. You will have to re-adjust the curb idle to keep it at the right spot as well.
If the truck is an automatic, once you have it set up so it runs right then put it in gear and try again although that will probably only need the curb idle adjusted if it stalls. hope this helps.

May 09, 2010 | Ford F-100 Cars & Trucks

1 Answer

Engine-no go


i think the dist is adjable try advanceing it some times the after market caps are a little diffront

Apr 06, 2009 | 1996 Ford Aspire

1 Answer

Transmission Problem


Its flood a tranny sensor causing a circuit fault, rain water conducts electricity. Locate this/these sensors and coat them with a sealing agent, your local auto parts store will have the stuff you need. No water, no short.

anaanymous

Oct 11, 2008 | 1995 Chevrolet S-10 CA Edition

Not finding what you are looking for?
1995 Chevrolet S-10 CA Edition Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...