Question about 1984 Toyota Tercel

1 Answer

Signals wont work and the 4 way hazard lights don't work. all other systems are working fine. fuses are good.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

I had this problem with my 85 tercel. I had to take it to an auto electrician who traced the wires for me. Basically one of the wires running to the driver side turn signal was shorting out causing no signals to work. Also check your bulbs because if one bulb goes out it effects the others.
Hope this helps!

Posted on Sep 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Chrysler Vision hazard light


on some of these models, the hazard switch operates through its own flasher fuse. if this is the case, locating and replacing the fuse ($4) should do it. Location should be in the owners manual.

Nov 10, 2013 | 1997 Chrysler LHS

1 Answer

Hazard lights malfunction


YOU MIGHT HAVE A BURNT OUT RELAY IN FUSE COMPART UNDER YOU CARS HOOD CHECK THAT OUT THRU YOUR CARS MANUAL,IT WILL SHOW YOU WHICH RELAY IT IS?

May 24, 2013 | Cars & Trucks

1 Answer

2000 tacoma flashers don't work but turn sig do work!


The hazard switch gets power from the horn fuse which is hot all the time, and from the turn signal fuse which is hot when the key switch is on. The turn signal switch gets power from the hazard switch and both use the same flasher.
So if the turn signals work but the hazard switch does not power the lights, and both fuses have power, I would say the problem is inside the hazard switch.

Feb 19, 2013 | Cars & Trucks

1 Answer

I need to find the flasher relay for a grand marquis 2001 .does it has one? My turn signals wont work I can hear the sound but don't even flash


Yes, it does have a flasher, although it may be a combined unit with the hazard flashers relay. So you hear the clicking of the flasher relay? That seems to indicate the relay is working properly. Have you checked the bulbs and the turn signal fuse? Any turn signal bulbs light up anywhere, front or back?
How about your brake lights, do they work? Your car may have separate, stand alone turn signals in the rear, but many American cars use the same bulb and same filament on the bulb for the brake lights and turn signals. If your merc is like this and the brake lights work, then the bulb must be good.
Turn on the hazard flashers and see if all bulbs work and flash at each corner of the car. This would be the same bulb as for the turn signals. If they work, it could be a bad turn signal switch, may even be the flasher relay somehow malfunctioning, and in a few cases, a bad hazard switch can affect the turn signal switch. Check fuses and bulbs first. If you have any type of body control module that controls lights and other accessories, you may have to investigate that. I know I'm not being very helpful, just throwing out a few suggestions. Good luck.

May 21, 2012 | 2001 Mercury Grand Marquis

1 Answer

How to fix turn signal on 86 Chevy Astro Van


you don`t say but do the lights work either on the front/back on both sides.if not then it may be a fuse that needs replacing or need a bulb replacement.if the lights work but don`t flash then it sounds like a signal flasher problem.the flasher is located in the fuse panel under the dash on the drivers side.if the hazard flashers work then turn them on to find the hazard flasher by the fuse panel then you will know what the signal flasher looks like and change the signal flasher.make sure you change the one for the signals and not the hazard one.if the hazards work then i would say the signal switch is good as the hazards work through the same switch.

Apr 21, 2011 | Chevrolet Astro Cars & Trucks

1 Answer

2004 monte carlo. Turn signals dont work. The stalk still works with other functions, such as wiper, brights. The fuse is fine. Could it be a bad relay? When u push the stalk up or down nothing happens on...


try pressing the hazards on and off if they still don,t work replace the flasher unit. it is built into the hazard switch( all one unit ) change this and all will be good.

Aug 30, 2009 | 2004 Chevrolet Monte Carlo

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

1 Answer

I have an interesting problem with my 01 Passat. The turn signals are not working, however the hazards are working. Could this be the hazard relay? The high beam on the right side is not working, and today...


The turn signals use one flasher and emergency uses another one. You can exchange the two (usually) for a quick check. The bad one will move to the other system when swapped, emergency flashers now don't work but the turn signals do. If this is the case go get a new flasher and replace it.

Mar 06, 2009 | 1998 Volkswagen Passat

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...