Question about Chevrolet Silverado 2500HD

1 Answer

Rear brake, signal, backup, and flashers do not work.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 59 Answers

Check fuses system in fuse box

Posted on Apr 05, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2000 jeep grand cherokee none of the rear lights work


Check BackUp Module, generally is located in the rear quarter panel (drivers side).

Dec 23, 2012 | 2000 Jeep Grand Cherokee

3 Answers

1994 Chevy C1500 truck. No rear brake lights


Most likely this is a brake light switch issue. Replace switch.

If your emergency flashers don't work, all flasher bulbs are fine, but flashing too fast, then check and replace Hazard light switch.

Oct 29, 2012 | 1994 Chevrolet C1500

1 Answer

No turn signal light 1993 Mercury Sable Wagon


You will have 2 flashers under the dash. First find the one that is clicking and you will see the other one close by. You can check the problem by removing the one that is clicking as its functioning ok because you have flashers working. after finding the other one switch them and you should have signals and no flashers. These will be located at the fuse block under the dash. Hope this helps you.

Aug 21, 2012 | Mercury Sable Cars & Trucks

1 Answer

Rear driver turn signal does not work, now neither does the driver front turn signal. no passenger brake llight. bulbs replaced, sockets replaced, lens assembly replaced. everything works when pluged...


The problem has to be in the multi function stalk if all of those parts were replaced correctly. This is the actual turn signal switch on the steering column.

Apr 16, 2011 | 1999 Jeep Grand Cherokee

2 Answers

I have a problem with a 93 Jeep Cherokee Laredo 4W - The right blinker & brake light works like they should. However,the left brake & backup lights are out ( new bulbs have been installed &...


a very bad earth in that lamp holder,, clean all the earths and try another new buld in it, iv had this before and that was the problem sorted

Nov 02, 2009 | 2000 Jeep Wrangler

1 Answer

2001 Sunfire rear brake/turn signal don't work.


check your fuzes. if that doesnt do you any good maybe a flasher or check for bad wiring. maybe a short somewhere

Jan 17, 2009 | 2000 Pontiac Sunfire

1 Answer

Rear lights


I think you have a bad ground in the rear lights. Try a new ground wire closer to the lights.

Aug 06, 2008 | 1993 GMC Sierra K1500

1 Answer

1991 Ford E150 turn signals do not work,emergancy flashers flash constantlly unless the flasher relay is unplugged from fuse block


Hi,

If I understand you right based on your post/description, the signal lights would still turn on even if any or both of the flasher relays are removed. Should this be the case, then the signal lights are not getting the power from the flasher relays but from the brake light circuit.

Perhaps your concern is not with any of the flasher, but simply missing or loose ground more particularly with the rear lights. Perhaps you could try determining which of the wires for the brake lights and signal lights (as they come out of the light assembly) would be ground . A test and even possibly a temporary workaround is to hard wire a second ground connection from the determined ground wire of the lights and attach it to any conveniently located bolt or screw to the body. it may be to your advantage to do this on all the rear lights assembly.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards. Thank you for using FixYa.

Aug 05, 2008 | 2003 Ford E150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...