Question about 1998 Oldsmobile Intrigue

1 Answer

I put head gaskits on my 1998 intrigue now i dont know wich plug wires go's in front or wich one's go in back

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,915 Answers

Here ya go:

i put head gaskits on - mikemt_9.gif

Posted on Apr 07, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change head gaskit 2003 vr6


if you do not have exsperiance or have the tools for it.
go to a garage.it will cost you double cause its an delicate,
job .that can go easly wrong.you have to drain all the water.remove,
all tubes -airfilter-carburator-valve cap.you need special tool to untighted the bolts from head gaskit in the wrigh order.get the head carrefully off.the head must be checked in the garage cleaned flattend.
put the new gaskit in the wright way back.then the head bolts must be tighten also in the right order and tension.put all parts back fill the cooling and get the air out the radiator.also the new has to rodate for atleast 500 km.there are some books or manuel how to do it.

May 04, 2014 | 2003 Volkswagen Jetta TDI

1 Answer

Spark plugs and wires how to change


do them one at at a time pull wire then plug when replacing plug just snug it over tight can strip plug hole in head then re place new wire before moving to next one that way they dont get mixed up wires must go back in same spots

Mar 18, 2013 | 2001 Oldsmobile Intrigue

1 Answer

Location of freeze plugs on 1998 crown victoria


on both sides of engine,on front and rear of cylinder heads and the dreaded on back of engine between motor and transmission

Dec 31, 2012 | 1998 Ford Crown Victoria

1 Answer

Looking to do a valve cover gaskit, is it very hard to do?


yes it is, basicaly because there is no valve cover gasket. if it leaks from the seem that would look like a valve cover leak then you have to pull off the top plate wich is actually the upper cam bearing. special tools are needed to remove or you WILL bust the front camshaft thrust plates off. they are part of the head

Sep 01, 2010 | 2001 Volvo C70

1 Answer

I'm trying to replace the spark plugs on a 2000 olds intrigue 3.5L. Is there a place I can find a diagram of the plugs' location? Can I do it myself or are the plugs hard to get to?


You should see 3 plug wires on the front side of the engine,remove them twist and pull straight out,to remove the wires.do not get them crossed,but place them where you know they will stay ,since they need to go back to the same spot,or plug.
The back side may be more difficult.If you cant reach them from the top you may need to go from the lower side under the car!! hopefully you can see the wires and remove them and the plugs from the top. A short length of 3/16 rubber vacumn line is verry useful to reinstall the plugs back into the plug holes,since the plug socket may be awkward,and you dont want to start them cross threaded,esp if the heads are aluminum.And if they are they need to be coated with anti seizeing compound! A gray looking grease!
Make sure the plugs have the right gap! Dont drop them on the dirty ground or hard concrete,if you do clean them and regap! Take your time,if you can and you may save some $$$$ good luck!

Aug 30, 2010 | Oldsmobile Intrigue Cars & Trucks

2 Answers

MY 1998 OLDSMOBILE IS OVERHEATING AND MY OIL


YOU'RE HEAD GASKET IS BLOWN,CHANGE YOU'RE HEAD GASKET AND PLEASE LET SOMEONE THAT KNOWS WHAT THEY ARE DOING DO IT.DONT RUN IT NO MORE.

Feb 03, 2010 | 1998 Oldsmobile Intrigue

2 Answers

I am fixing to change spark plugs in my 1998 OLDS Intrigue, it has a "3800 series 2" motor in it. The front plugs doesn't look like much of a problem, but the back ones look like they may be pretty hard to...


yes it would be alot easier that way but if you can't do that you can get them out with just enough room with a 3" extention and a swivel head ratchet . i do them all the time. will get cut up a little bit but not to bad. the front like you said is a breeze.

if you have any more question please ask

Oct 29, 2009 | 1998 Oldsmobile Intrigue

2 Answers

I need a spark wire diagram for a 1998 3.8 olds intrigue


Viewing the front of the engine, going from the front to the back, the left side cylinders are 2, 4, and 6.
The right side cylinders are 1, 3, and 5.
The firing order is 1-6-5-4-3-2

May 19, 2009 | 1998 Oldsmobile Intrigue

2 Answers

I need to know where i put the power steering fluid at


its on the passenger side real close to the fire wall on the back of the engine

Jan 16, 2009 | 1998 Oldsmobile Intrigue

Not finding what you are looking for?
1998 Oldsmobile Intrigue Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...