Question about 1984 Ford Crown Victoria

Open Question

Remove rear seat back cushion in a 1984 Crown Victoria

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: 2005 Jeep Grand Cherokee rear seat removal

For the seat bottom, you just need to pull it up. The seat backs would have to be unbolted.

Posted on Mar 06, 2009

Ad
arquetteg
  • 37 Answers

SOURCE: I need to get my 97' Crown victoria trunk open from the inside.

There should be a safety trunk release located on the upper rear window deck platform- a black handpull . If it is still intact- it should pop the trunk lid.

Posted on May 27, 2009

  • 70 Answers

SOURCE: how to remove rear axel from ford crown victoria

do u mean the axle has "play" when u grab the tire and wiggle it up and down?? if it has play, then it propbably needs an AXLE SEAL AND AXLE BEARING.you will have to carefully inspect the axle itself where the bearing rides for any gouging or damage. THIS JOB requires a decent amount of mechanical skill. 1ST you need to remove the rear end COVER and drain out the gear oil into a drain pan.2ND remove the brake caliper and rotor . 3RD spin the" ring and pinion " around until u see a 5/16 bolt that passes thru from the pass. side to the drivers side. u have to remove this bolt. u will need to "hold "the gears from turning in order to break loose this bolt. 4TH remove this bolt and slide out the large metal ""PIN" that 'divides" the rear end in half. NOW CAREFULLY WITHOUT TURNING THE REAR END SPIDER GEARS,PUSH IN THE AXLE TOWARDS THE INSIDE SO U CAN REMOVE THE "C-CLIP" AT INNER END OF AXLE. now u can slide out axle and youll be able to replace seal and if needed axle bearing. let me know if u need more info.

Posted on Sep 06, 2009

  • 4340 Answers

SOURCE: 05 crown victoria police package rear axle removal

there are two main designs. One uses a bearing and flange at the backing plate area, release that and you can pull the axle and bearing.

the Other design is call a c lock axle. Inside the carrier, there are 4 spider gears. Two are splined to the alxes and two idle on an idler shaft. Remove this shaft, and then you can push the axle shaft inwards about an inch or so.

this will allow you to remove the c shaped retainer that is engauged with a groove at the inboard end of the axle.

So, now the bad news: often the c lock axle uses the axle shaft itself and the inside bearing race...which means if the bearing has failed, you need to replace the axle also.... Inspect carefully. Metal temper is the issue and once that is comprimised, you need to replace.

Doc

Posted on Sep 19, 2009

SOURCE: how do you remove the rear seat( btm cushion) from

grab the bottom of the cushion just under the lip of the back seat and pull it towards the front of the vehicle and then up. Saturn uses little plastic clips to hold the cushions down to the rear molding.
\
when you want to put it back in, just press on the clips until they click.......you will be good to go

GOOD LUCK AND PLEASE RATE THIS POST!!!!! :D

Posted on Mar 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford crown victoria 1984 top speed ?


Question has no proper answer because so many factors affect this--tune up, tire size, rear axle ratio, weather, road condition, milage on car, etc.

Sep 30, 2016 | 1984 Ford Crown Victoria

2 Answers

How to remove the headrests to put seat covers on for a 1989 crown victoria?


90% of head rests just pull out. the others will have a button where the headrest goes into the seat. If yours doesn't have the button, then push the headrest down and **** it up with some force and it will come out. Just be carefull you don't hit yourself in the face with it. Been there done that

Feb 08, 2011 | 1996 Ford Crown Victoria

1 Answer

Truck lock is jammed by briefcase strap. can i get into the trunk from the back seat? such as does the back seat fold down?


I searched the owner's manual and there was no mention of folding the rear seats down. If you don't have a manual, you can get one here: http://www.extendedgmwarranty.com/owners-manual/buick/1999-Buick-Century.pdf

You can remove the seats following the instructions below from autozone.com.
Rear Seats
SEAT CUSHION


jturcotte_98.gif

Fig. Typical W-Body rear seat cushion removal

  1. Locate and remove the small bolts at the front lower edge of the seat cushion.
  2. Pull the tabs on the rear cushion retainers.
  3. Remove the seat cushion by lifting up and pulling out of the retainer.
  4. Installation is the reverse of the removal procedure. Make sure the retainer tabs are snapped into place. Tighten the bolts to 18 ft. lbs. (25 Nm).

SEAT BACK


jturcotte_99.gif

Fig. Typical W-Body rear seat back removal

  1. Remove the seat cushion as described above.
  2. Remove the anchor nuts securing the rear seat retainer at the bottom of the seat back.
  3. Grasp the bottom of the seat back and swing upward to disengage the offsets on the upper frame bar from the hangers.
  4. Lift the seat back upwards to remove from the vehicle.
  5. Installation is the reverse of the removal process. Make sure the hooks on the seat back are properly installed to the hangers. Tighten the anchor nuts to 89 inch lbs. (10 Nm).

Nov 07, 2010 | 1999 Buick Century

1 Answer

How too remove back seat in a 1995 Nissan Maxima


Rear
See Figures 3, 4, 5 and 6
  1. Remove the lower seat cushion by pulling straight up on the front portion and disengaging the clips. Then hinge the seat upward to release the rear clips.
03b6e0a.jpg

Fig. 3: Pull up on the front of the lower seat cushion and disengage the clips
  1. Remove upper rear seat back-to-chassis bolts.
77eb191.jpg

Fig. 4: Remove the bolts behind the center armrest ...

a796228.jpg

Fig. 5: ... and the bolts on the lower corners ...

fbf100a.jpg

Fig. 6: ... Then pull up on the seat to disengage the three clips on the top of the seat
  1. Remove rear seat back by tilting forward and pulling straight up.

To install:
  1. Install the lower seat cushion and torque the lower rear seat-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm).
  2. Install the upper rear seat back cushion and torque the upper rear seat back-to-chassis bolts to 15-20 ft. lbs. (21-26 Nm)

Hope help with this (remember rated this).

Jul 19, 2010 | 1995 Nissan Maxima

1 Answer

How do i remove the backseat in my thunderbird?


Rear Bench
(see Figure 4)
  1. Bearing down with your knee on the rear seat cushion, push the cushion rearward and disengage it from the retaining brackets.
  2. Remove the rear seat armrests if applicable.
a32ebe2.jpg

Fig. 4: Pull the bottom of the seat upwards and pull out
  1. Remove the seatback lower retaining screws and seat belt bolts.
  2. Grasp the seatback at the bottom and lift it up to disengage the hanger wire from the retainer brackets.

To install:
  1. Position the seat back assembly so that the hanger wire is fully engaged in the package tray slots.
  2. Install the lower retaining screws and tighten to 13-19 ft. lbs. (17-37 Nm).
  3. Position the seat cushion assembly into the vehicle.
  4. Apply knee pressure to the lower portion of the seat cushion assembly. Push rearwards and down to lock the seat cushion into the seat retainer.
  5. Check the seat cushion to ensure it is secured into the floor retainer.

Rear, Fold-Down Seats
  1. Push the rear cushion rearwards, then lift to release. Remove the cushion.
  2. Remove the 2 lower retaining screws attaching the seat back to the floor.
  3. Lift up and disengage the upper clips of the seatback from the top of the folding floor.
  4. Remove the seat assembly.

To install:
  1. Position the seat back assembly and align the retaining hooks. Ensure hooks fully engage in slots.
  2. Install the two outboard retaining bolts, then tighten to 13-19 ft. lbs. (17-27 Nm).
  3. Lower the seat backs and install the upper retaining screws.
  4. Install the lower center retaining screw, tighten to 13-19 ft. lbs. (17-27 Nm).
  5. Install the rear seat cushion. Ensure the rear seat cushion front retainers latch properly.

Hope helps (remember rated this).

Jul 01, 2010 | 1994 Ford Thunderbird

1 Answer

Reaching rear seat belt on 1997 crown victoria


Lap belt or shoulder harness? Lap belt - remove rear seat bottom by pushing in on bottom edge of the seat cushion and lifting. This will expose the lap belt and its anchor. Shoulder belt should be accessible via trunk compartment. If not then you'll have to remove the back of the rear seat to get to it.

Oct 04, 2009 | 1997 Ford Crown Victoria

1 Answer

How to take out the back seat backrest


Push down on the rear of the seats part of the backseat and it should release and pop loose. Remove it.

Then there are two bolts at the bottom of the seat back, remove these and it should come out easily

Sep 10, 2009 | 1996 Ford Crown Victoria

1 Answer

I need to get my 97' Crown victoria trunk open from the inside.


There should be a safety trunk release located on the upper rear window deck platform- a black handpull . If it is still intact- it should pop the trunk lid.

May 27, 2009 | 1997 Ford Crown Victoria

1 Answer

Mustang rear seat removal?


please rate highly if this is what you need

Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Cushion, Rear Removal and Installation
  1. Release pin from locks by pressing release button under rear seat cushion.
  1. Pull rear safety belt and buckle (60044) through openings in rear seat cushion pad and frame (600A88) and remove rear seat cushion pad and frame .
  1. To install, reverse Removal procedure.
----------------------------------------------
Section 01-10: Seats and Tracks 1994 Mustang. Workshop Manual
REMOVAL AND INSTALLATION Seat Back, Rear Sedan
Removal
  1. Remove rear seat cushion as outlined.
  1. Remove rear seat bolster. Refer to Section 01-05 .

  1. Remove rear seat bolster mounting bolts. Remove bolster assembly.
  2. Remove four seat back to package tray retaining bolts.
  1. Remove seat back.
  1. To install, reverse Removal procedure.

May 04, 2009 | 2004 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...