Question about 1999 Chevrolet Silverado 1500

1 Answer

My a/c clutch will not enage - 1999 Chevrolet Silverado 1500

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that gotĀ 5 achievements.


    An expert who has achieved Level 3.


    An expert that hasĀ over 500 points.

  • Master
  • 500 Answers

Often this is because of low freon there is a pressure switch on the accumulator can the big silver reservoir that switch .. Unplug that switch & jumper the the SW with a wire this should start clutch unless its a fuse,,

Posted on Apr 05, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I have a 1981 corvette and the heat/a/c stop working

If you add to much freon the air compress won't enage and your a/c want come on.

Sep 22, 2014 | 1981 Chevrolet Corvette

1 Answer

My actros 3351 firetruck,is jumping from reverse when it is enaged to reverse

at our stations, we call county service, they dispatch a mechanic
and bingo , i fix it.

Jun 29, 2014 | Cars & Trucks

1 Answer

Starter motor working fine and engages into ring but ring gear doesnt crank/turn when enaged. I took stsrter.motor off and tried turning the ring gear myself but it wont move. I just finish putting in a...

I would say that you have made an error in fitting the gear box that is jamming the flywheel to tight IF the gearbox didn't go all the way in so that the housing touched the rear of the engine all the way round then the clutch shaft has not fully engaged the spigot bearing in the crankshaft causing the problem. Loosen of the bell housing bolts until you can turn the flywheel to see if that is the problem.

Aug 03, 2013 | Cars & Trucks

1 Answer

1997 GMC Sonoma 4x4 not engaging

sounds like its tring to enage but won,t. making a moaning noise. changed shift cable and actuator

Jan 03, 2013 | GMC Sonoma Cars & Trucks

1 Answer

Delay in 1st gear

first check the fluid level and the condition of it.

Sep 20, 2012 | 2005 Nissan Sentra 1.8

1 Answer

A/c will not come on and cluth will not enage

Have you checked the system to see if it is low on freon ?

Jul 27, 2012 | 1998 Jeep Cherokee

1 Answer

My 93 chevy g 20 vans air stopped blowing but when you move the switch you can still hear the compressor engage, before this happened it would come on and off if you slammed the door what could it be?...

Check blower motor. Compressor is doing its cold air work but you need the blower fan to get it into your can/van. You could simply have a loose connection. Follow the wires and try unplugging it and pluggin' it back in. Could also be a fuse or relay. When you say you slammed the door, sounds like a loose connection. Any wires hot or being pinched? See anything thing that looks melted under there?
Also, are you hoses connected to your vents under the dash???? That is easy enough to unscrew and check. Good luck

Jun 14, 2011 | 1993 Chevrolet G20

1 Answer

Front brakes on my 1995 Dodge Ram 2500 Diesel won"t enage.

sounds like its time for new calipers...maybe. but thats what I did, mine is a gas motor, but shouldnt be different.

Jan 18, 2011 | 1995 Dodge Ram 2500

1 Answer

1999 tracker,when I enaged the 4x4 it only stay in for a few seconds.It doesn't matter if it's 4h or low.It does enage into the transfer case.

you'll need to get it up on a lift or some level ground+ 4 jack stands now with all 4 in the air have somone
in the car to start and engage the 4wd if the output
shaft is turning into the differential and does not stop
turning if the wheels do you may have a bad hub
I hope this helps any other ? gimme a shout
good luck

Jan 14, 2010 | 1993 Geo Tracker

1 Answer

I have a 1997 F150 4X4. The front axle won't enage

I also have a 97 F-150 4x4. If that was my truck I first would change the fluid in the transfer case. See if that helps loosen it up. It is possible that it has the wrong fluid in it.

Oct 28, 2009 | 2004 Ford F150

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides