Question about 1994 Toyota Pickup

1 Answer

How do i replace the wheel bearings in the front of a 1994 toyota pickup 4wd 4cy 22re?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 37 Answers

You will have to take the wheel hub assembly off the vehicle. Which means you will have to remove the calipers, detach the tie rods, loosen the ball joints, and the strut assembly. Then remove the hub locks and the axle retaining nut. Take the hub and new bearings to a machine shop and have the old ones pressed out and the new ones pressed in. The wheel bearings have to be pressed in and out to prevent any damage to the hub itself.

Posted on Apr 05, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

22re trouble code 24 and 32


24 Intake air temp sensor and 32 mass air flow meter circuit or vacuum switch failure . Air temp sensor is internal in the vane style mass air flow meter it is not replaceable you will need a new meter.

Mar 21, 2014 | 1994 Toyota Pickup

1 Answer

Front wheel bearing


There is no question there

Google the question

Go to You Tube Video-- to see how to replace the
wheel bearing hub

Aug 22, 2013 | 1994 Toyota Pickup

1 Answer

93' toyota pickup 4wd 4 cylinders 22re, sputters when given throttle


Low fuel pressure can cause this or a clogged filter, has the fuel pressure been checked? Has the fuel filter ever been changed?

Feb 13, 2013 | 1994 Toyota Pickup

2 Answers

Where is the fuel filter located on a 1994 toyota pickup?


Not sure what engine you have, but on the 22R or 22RE (2.4 liter four cylinder) It's on the right side (passenger) lower engine just above the oil pan, and in front of the starter motor. You go through the inner wheel well just above the right front wheel. There is an access panel.

May 21, 2010 | 1994 Toyota Pickup

1 Answer

How do you install a clutch on a Pick up Toyota 1994


What engine? four wheel drive?
Remove rear drive shaft, transfer case if it is four wheel drive, and front drive shaft.
Remove transmission.
Get the kit to replace clutch disk, pressure plate and throw out bearing.
If the flywheel is worn, or grooved, replace it or get it turned at a machine shop.

Apr 29, 2010 | 1994 Toyota Pickup

2 Answers

Where is the fuel pump located on a 1986 toyota pickup truck?


on my 83 2wd truck, facing the engine, it is on the top left at the front of the engine, with one small hose going in the top, and two hoses coming out of the side.....that is for a 22r engine...which i think yours has also

Mar 21, 2010 | 1986 Toyota Pickup 4WD

1 Answer

Where is the fuel filter located on my 86 4wd (22re)


You're going to laugh when you hear this...not! It's under the intake manifold, bolted to the side of the engine block. It's a real pain to do.

Jan 12, 2010 | 1986 Toyota Pickup 4WD

1 Answer

I need to replace the water pump on my 1994 4wd truck (22Re). How do I get the old one out?


drain cooling system, remove fan & fan clutch, remove bolts around the waterpump....make sure you clean the surface before reinstalling the new pump and gasket!! Its a fairly easy job!! Hopefully this helps!!

Jul 20, 2009 | 1994 Toyota Pickup

2 Answers

Overheating and water mixed in with oil


Absolutely correct. Have cylinder head dye tested and checked for warpage before re-using. Do not run the engine any more than necessary ( into the garage or onto flatbed on it's way to shop) or you risk doing damage to engine bearings.

Mar 21, 2009 | 1994 Toyota Pickup

1 Answer

1994 22re 4x4 problem


your transfer case is not working properly, try this trick, shift into 4wd and gently back up the car and go forward and back up again wait for the indicator light to come back again, goodluck, otherwise you need to have those transfer case checked and maintained, have those front hubs checked and maintained too. Its would be better to use your 4WD more often. Try this trick not on a paved road pls.

Nov 25, 2008 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
1994 Toyota Pickup Logo

531 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...