Question about 1992 Cadillac Seville

1 Answer

When you floor it from a dead stop; 1st gear will not change when it hits the red line. it bounces off of it, and you have to let off to get it to change to second. or, it will start over-reving.

Posted by on

  • 1 more comment 
  • JESSIE BRADSHAW Apr 05, 2011

    There is only two cables that run to the throttle body. One is the accelerator pedal cable, and the other is the cruise control cable. Is there anything else that could cause this problem.

  • JESSIE BRADSHAW Apr 05, 2011

    I figured out what the problem was. The modulator on the tranny and the seal around it were worn out.

  • JESSIE BRADSHAW Apr 08, 2011

    I will try this and let you know if this works.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,702 Answers

?????

Posted on Apr 06, 2011

  • john nail
    john nail Apr 06, 2011

    sorry about the first post, but i was testing the link to make sure it was working, fixya has been having some problems with the sight, we have not been able to post an answer to you question do to the technical problems on the sight, i tried to answer your question several times yesterday but was unable to do to the technical problems.



    so with all that said lets get to you 1992 cadillac.



    what you are describing is a stuck governor in the transmission, but i do have a question can you manually shift the gears? what i mean is if you put the shifter in low range and take off then move the shifter threw the gears manually will the transmission shift? if it dies then it is probably just a stuck governor, and you might be able to just service the transmission and fix the problem, you service this transmission by removing the transmission oil pan and replacing the internal oil filter then refiling the transmission with new ATF and a qt if transX ( it is like miracle juice in a can ) it take the transX around 100 miles to start working it magic, if after a 100 miles or so the problem has not gone away, of if you can not shift threw the gears manually then you most likely will have to replace the transmission, but don't give up hope yet give the transX a chance it is a great product, we use it almost daily in our shop.



    if there is any thing else i can do for please let me know.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an automatic transmission. My car switches from 1st gear to second with a thump and then it reeves up to the RPMs get into the red and wont switch into the next gear.


Im not a expert but have you checked the trans fluid level? Ck forleaks , vacume line uphooked. Ck to see what color the fluid is and possable plugged filter inside the pan

Sep 11, 2015 | Cars & Trucks

2 Answers

2007 mustang gt have engine knock problem when going from 1st to 2nd gear at 5000 rpms?


5.000rpm's high revs and you run into problems with valve bounce ( hitting pistons) ,ring slap, gudgeon pin knock, big end noise and possible main bearing noise . You may also be getting a hydraulic lock in the hydraulic followers that is holding the valves open too long. Unless the engine has been specifically built for these rpm's any loose ,worn on unsuitable part will cause problems I am thinking that you have around 100.000 miles on the clock after 7 years and the motor is not young Ford V8 engines specifically built for a 500 klm race are limited to 5.500 rpms because they destroy the timing chain if driven over that speed .

Jun 03, 2014 | 2007 Ford Mustang GT

1 Answer

I have a 2008 GMC Yukon XL Denali. I hit a small snow drift yesterday and now my speedometer stopped working, my RPMS are bouncing, oil pressure is bouncing, temp is bouncing and vehicle wont shift out of...


Vehicle speed sensor, wheel speed sensor, your VSS operates you MPH and tells the trans how fast you are going and when to shift, it is telling the trans that your not moving so why would it shift? Next your ABS wheel speed sensor tell the car what wheel is moving at what speed to activate traction control and abs systems both are very sensitive and easy to break

Dec 29, 2013 | GMC Yukon Denali Cars & Trucks

1 Answer

1995 Jeep Wrangler Auto Trans 1st to 2nd shift acts like it goes into neutral what could the problem be


When was the last time the transmission fluid and filter changed? I would have that serviced first. If it is an electronic transmission, the line pressure might also have to be reset.

Aug 15, 2017 | 1995 Jeep Wrangler

1 Answer

1995 dodge when accelerating from a stop my truck bounces


Check your rear shocks, what you are experiencing is called axle ***** and is usually caused by worn shocks.

Mar 07, 2012 | 1996 Dodge Ram 1500 Club Cab

1 Answer

1986 F250 manual 4 speed tranny. replaced slave and master. still same problem have clutch all the way to the floor to change gears and some times still not enough to change gears. its only in 1st and...


yes it sounds like the clutch is worn.1st thing when a cutch wears is its hard to get in reverse
as long as all air is bleed out(pedal feels normal)not a bad job unless its 4 wheel drive
good luck

Jun 12, 2011 | 1986 Ford F 250

1 Answer

Lincoln Navigator transmission problem


check and replace filter and fluids just like oil it tends to burn up and blacking and needs to be changed and flushed checking your tranny fluid it should be a red color not a dark red or with a black tint

Jun 25, 2009 | 2003 Lincoln Navigator

2 Answers

Goes to 4000 rpms to 5500 rpms before changing from 1st to 2nd g


Ford : back the truck up 10ft put truck in neutral and disengage four wheel low. (You can't drive in four wheel low cause its a pulling gear and you won't do over 3-5 mph.)
Nissan: start truck see if it idles normal. If so rev motor and check throttle for sticking and check EGR valve make sure its not stuck open or malfunctioning when you drive it..

May 24, 2009 | 1992 Nissan Pickup

2 Answers

I have no owner's manual for my 2000 Landcruiser/What buttons do


overdrive is used when you are trying to accelerate going up a steep hill. have you ever noticed when you are going up a hill that you can not maintain speed? hit this button and you wount need to floor it

Jan 13, 2009 | 2000 Toyota Land Cruiser

Not finding what you are looking for?
1992 Cadillac Seville Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...