Question about 1990 Ford Probe

1 Answer

Im look for a sender unit for 1990 ford probe

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There are many sending units on your engine. which one are you looking for and which engine do you have?

Posted on Apr 05, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My oil gauge isnt working at all


Check if the sender is working. What type of gauge is in the truck? If it is an electronic type like the gas gauge, you can use an assistant and ground the sender lead with a resistor (100 ohm 1/2 w) and see if the gauge moves. If it does, then the sender is bad. If it does not, then the gauge or wiring could be at fault.

Most cases it is just the sender.

Thanks, Jim

Mar 08, 2011 | 1990 Ford F150

2 Answers

Location of oil sending unit? on a 1990 ford ranger with a 2.3l


Drivers side about 3" from the back about 2" from the oil pan. Will have a single black wire leading from it to the wire harness
Hope this helps
Please leave feedback Thanks

Dec 24, 2009 | 1990 Ford Ranger SuperCab

1 Answer

I need a 1990 ford probe fuse box diagram


Go to auto zone or O'reilley auto parts and buy the chilton Ford Probe 1989-1992 Repair Manual. Best source to fix almost anything on your Probe.

Sep 01, 2009 | 1990 Ford Probe

1 Answer

Gas gage don't work1990 ford rainger


usually the sender units wire is loose or the send is faulty
you can check the sender by removing it or you can check the guage from the sender end by varying the voltage
i just use torch batteries 1 the 2 then 3 in series just like inside the torch!
If guage shows different levels 1/4 or 1/2 etc.then its the ender unit thats faulty

Jul 18, 2009 | 1990 Ford Ranger SuperCab

2 Answers

Just quit running while driving will still turn still over, getting fuel thought filter, i dont think im getting fire. 1990 2.2L ford probe


i had the same thing happen to me after it turned 200,000 miles.

All you have is a bad electric connecter to the fuel rail it's located over by the battery and that should help your problem.
i hope this helps and good luck.

i'm on here looking beacuse mine is hard to get started.

Sam


Jul 03, 2009 | 1990 Ford Probe

1 Answer

Wiring on plug for fule sending unit


one wire usually to sending unit (which is a rheostat ) from inside it is soldered then up and out to plug....repair anyplace you can get a length of wire to work with or solder a new one in place where old exists now and out to your torn wire..good luck

Jan 13, 2009 | 1990 Ford Probe

1 Answer

1990 holden rodeo /isuzu pick-up temp sender


from memory it is in inlet manifold some were in front middle section bottom, (underneath) 4ZE1?
single wire possibly yellow

Dec 16, 2008 | 1990 Isuzu Pickup

1 Answer

1991 ford probe


duck tape on the air intake. I just fixed mine. There is a crack on the intake that lets too much air in when you put it in drive that makes the car stall. Try it it works.

Nov 23, 2008 | 1990 Ford Probe

1 Answer

Fuel gauge


hi, check fuses,if all are ok then it will be the sender unit inside the fueltank that will need replacing,but check sender unit electrical connections first and clean before removing unit,All the best and hope this is usefull.Phil

Aug 27, 2008 | 1990 Ford Probe

1 Answer

2005 FORD TAURUS


Switch ig. on, ground the sender unit wire for about 3 seconds see if the temp. gauge moves, if so change sender unit, if not then it is a faulty gauge reader.

Jul 29, 2008 | 1990 Ford F350

Not finding what you are looking for?
1990 Ford Probe Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...