Question about Isuzu Pickup

1 Answer

Bucking / missing when holding steady speed / about 55 mph

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 77 Answers

Could b bad plug wires

Posted on Apr 05, 2011

  • gordon king Apr 05, 2011

    when was last tune up ??? change gas filter ?? a lot ov things could make that happen i would try filter and plugs first

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the drive cycle for a 2003 Nissan Sentra SE?


Take extra caution while performing dirve cycles on public roadways. Drive cycles can be difficult to follow under normal driving conditions. Begin by: - Start the engine. Idle the engine in drive for two and a half minutes with the A/C and rear defroster on. - Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. - Hold at a steady speed of 55 mph for three minutes. - Decelerate (coast down) to 20 mph without braking or depressing the clutch. - Accelerate back to 55 to 60 mph at ¾ throttle. - Hold at a steady speed of 55 to 60 mph for five minutes. - Decelerate (coast down) to a stop without braking. If all other emissions systems are functioning properly, completing the drive cycle above will set the "readiness flags" required to pass the smog check. It will not hurt to perform the drive cycle 2 or 3 times before the smog test.

Oct 06, 2016 | 2003 Nissan Sentra

1 Answer

Car bucking at speeds above 60 mph


could be sensor has failed or could be in need of tuneup...

Aug 16, 2012 | 2000 Volkswagen Beetle

1 Answer

Drive cycle


Here is the OBD2 emission system drive cycle test procedure.
Engine coolant temp must be below 70c (158f) before starting the engine for either the first or second trip
The fuel level should be less than 1/2 full
First trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" for at least 10 seconds (not more than 5 min)
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary.
End of first trip. Turn the key off the begin the second trip.
Second trip:
Start engine, idle for at least 1.5 minutes
Drive 3 minutes, hold b/f schdl: 1.5-2.0 msec, selector lever "3rd" eng rpm 1,800-2,000 A/C switch:ON Hold the recommended b/f schdl range. Allow road speed to vary as necessary.
Drive at 55-65 mph for 1.5 min b/f schdl 2.0-3.2 msec, selector lever "5th" Engine rpm 2,200-3,000
IGN "off" add four gallons of fuel
Dive at 50-60 mph for 3 minutes Selector lever "4th" keep engine speed above 3,000 rpm Allow speed to vary if necessary. Do not decelerate for more than 3 consecutive seconds. A/C switch ON.
Drive at a steady state cruise of 53-58mhp b/f schdl more than 1.8 msec selector lever "5th" eng rpm 2,400-2,600
Downshift to "4th" and decel more than 5 seconds without breaking, then idle for 1 minute.
Drive two minutes b/f schdl less than 2.0 msec Accelerate to 41 mph, decelerate to 34 mph, accelerate to 41mph. Do not completely release the accelerator. A/C switch off.
Idle 1 minute in park or neutral
Drive two minutes Steady state cruise at 31-44 mph. Selector lever "4th" A/C switch OFF. Hold the accelerator pedal as steady as possible. Allow speed to change if necessary. I especially like the part where they want you to add four gallons of fuel. Not three gallons, not five gallons, four gallons. Gotta love those Nissan engineers. ...and of course they state that if the trace is not followed exactly (i.e. you botch the acceleration/deceleration) you have to start all over again from scratch

Feb 09, 2012 | 1996 Nissan Pickup

1 Answer

NEED DRIVE CYCLE FOR 2004 CRV TO RESET CAT AND O2 MONOTOR


Here is the info

NOTE: The ignition key must not be on prior to the cold start otherwise the heated oxygen sensor diagnostic may not run.

1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge.

Oct 02, 2010 | 2004 Honda CR-V

1 Answer

How do i do the drive cycle on a 1997 nissan pathfinder


The following drive cycle can be used as a guide to assist with re-setting monitors when a vehicle specific drive cycle cannot be located. This OBDII drive cycle begins with a cold start (coolant temperature below 122 degrees F and the coolant and air temperature sensors within 11 degrees of one another). This condition can be achieved by allowing the vehicle to "sit" overnight, and then by beginning the drive cycle the next day. Most drive cycles will be difficult to follow exactly under normal driving conditions, so the driver should exercise caution, road safety, and courtesy to others.
  1. . Start the engine. Idle the engine in drive for two and a half minutes with the A/C and rear defroster on.
  2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle.
  3. Hold at a steady speed of 55 mph for three minutes.
  4. Decelerate (coast down) to 20 mph without braking or depressing the clutch.
  5. Accelerate back to 55 to 60 mph at ¾ throttle.
  6. Hold at a steady speed of 55 to 60 mph for five minutes.
  7. Decelerate (coast down) to a stop without braking.

Sep 17, 2010 | 1997 Nissan Pathfinder

2 Answers

Reset computer in doege stratus wont pass inspection drove 50 miles and computer still didnt reset help


U have to operate the engine at all kinds of diff speeds and drive modes, it is called a OBDII drive cycle, here is how u do one.
1. As soon as the engine starts, idle the engine in drive for two and a half minutes with the A/C and rear defrost on. OBDII checks oxygen sensor heater circuits, air pump and EVAP purge.

2. Turn the A/C and rear defrost off, and accelerate to 55 mph at half throttle. OBDII checks for ignition misfire, fuel2_bing.gif trim and canister purge.

3. Hold at a steady state speed of 55 mph for three minutes.

OBDII monitors EGR, air pump, O2 sensors and canister purge.

4. Decelerate (coast down) to 20 mph without braking or depressing the clutch. OBDII checks EGR and purge functions.

5. Accelerate back to 55 to 60 mph at half throttle. OBDII checks misfire, fuel trim and purge again.

6. Hold at a steady speed of 55 to 60 mph for five minutes.

OBDII monitors catalytic converter efficiency, misfire, EGR, fuel trim, oxygen sensors and purge functions.

7. Decelerate (coast down) to a stop without braking. OBDII makes a final check of EGR and canister purge

Jun 02, 2010 | 2004 Dodge Stratus

1 Answer

Sitting at a steady speed on motorway it stutters


If you are travelling at about 55 to 65 mph and it does this then your wheels need balancing its about £7 per wheel and nothing to worry about, but do get it done asap. other thing could be the brakes but its unlikey you would feel it at speed.

Jan 13, 2010 | 2005 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...