Question about Ford Ranger

1 Answer

I change plugs cap and rottor but it is still not hitting on two cyl its a 88 ford ranger 2.3 l

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 27 Answers

Have you replaced the plug wires also? As a general rule of thumb it is also wise to change plug wires when changing other ignition components. If one or more of the wires are cracked or or dryrotted, the wires will arc and therefore cause the cylinders to miss. Try replacing all ignition wires as they generally only last about 20,000 miles before they start to deteriorate.

Posted on Apr 05, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Could my distribitor be bad?


is there a dist first or a coil pack are all the plugs good and do they have spark on each when you say it fires on 2 cyls which ones and do you have a check engine on you can check the codes and it should help you but if you have a dist you also have a rotor as well by removing the cap you should see corrosion under where the rotor hits on as well you have a pickup coil but dont go so far check plugs first for ware then go from there wires, coils, etc

Aug 06, 2014 | 2003 Ford Ranger Regular Cab

1 Answer

My 88 ford ranger with 2.9 electronic fuel injection is missing real bad and backfiring and dont even have enough power to climb my drive way i adjusted the timing changed fuel pumps and distributer a


Check that you have the plug leads on the distributor cap the right way around and that the cap and rotor are in good condition and secured properly.

Nov 06, 2012 | 1988 Ford Ranger

2 Answers

2003 ford ranger edge regular cab 3.0 Liter 6 Cyl.. 2 problems...Replaced Plugs and wires. Truck idles rough (especially after running for awhile) and misses when driving. You can...


You state you changed plugs and wires - Do distributor cap & rotor? If not you should then set timing. That should cure hesitation (might change fuel filter also and run good fuel system cleaner through it)
Prob 2 - sounds like a u-joint or possible brake pad/rotor issue. Does the squeal only happen in mornings when cold? Sometimes after sitting overnight, rotors get condensation and when backing out they'll squeal/grind. Somethings to look at...

Feb 27, 2011 | 2003 Ford Ranger Regular Cab

1 Answer

2004 ford ranger 4 cyl. Problems bleeding clutch after master cyl replacement


Use a vacuum pump and fake cap o nthe master cylinder reservoir to pull the system into a vacuum while not pressing and then while pressing the clutch to extract the air.

Oct 06, 2010 | 2004 Ford Ranger

1 Answer

2002 ford ranger 3.0 is missing on 2 cyl plugs ok injectors ok new coilpack


do a compression test,as the intake manifold,like alot of fords is no good.

May 22, 2009 | 2000 Ford Ranger SuperCab

1 Answer

Messed up wiring spark plugs on my 88 mustang 5.0 how to fix it


1-3-7-2-6-5-4-8 ccw the cap should have a 1 on it for cyl #1

Dec 28, 2008 | 1988 Ford Mustang

1 Answer

88 ford ranger


1988 Ford Ranger 2WD
2.0 liter SOHC L4

9611fc8.gif
1988 Ford Ranger 2WD
2.3 liter SOHC L4

b2ba47b.gif
1988 Ford Ranger 2WD
2.9 liter V-6

3900f5e.gif
The firing order is the same in the 4wd specs also.

Sep 25, 2008 | 1990 Ford Ranger SuperCab

1 Answer

How hard or easy is it to change a heater core on an 1988 ford ranger


Check my tips and tricks in my profile. If you have a 88 ranger 4 cyl. like mine. It's a piece of cake. I can't imagine the 6 cyl version being that much more complicated but I haven't worked on one. If you have any mechanical skills and common screwdriver bits or small sockets it should take you all of 30 mins. And like everything else I ever had to replace on the truck it costs $25 - $35.

Sep 20, 2008 | 1988 Ford Ranger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...