Question about 1995 Jeep Grand Cherokee

1 Answer

A/c clutch does not work - 1995 Jeep Grand Cherokee

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 84 Answers

1. check fuses
2. check low refrigerant
3. check wire going to clutch
4. with volt meter or test light check clutch wires / bypass clutch turn A/C on; turn ignition on; does the light - light?
5. with ohm meter check cluch wiring - cluch may have burned out

Posted on Apr 05, 2011

  • jjejuice.com
    jjejuice.com Apr 05, 2011

    it turns off and on. using a test light i test the power going to the clutch and it goes off and on. fues is good.

  • feestrings Apr 05, 2011

    light goes off and on with the cluch disconnected - then it sounds like you have a bad ground wire connection or a shorted wire in your A/C wiring or the control pannel switch may be making and braking circute (bad switch).
    you will have to test further - any of your connections may be falty - no easy answer.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch pedal engages almost at the top not close to thefloor


have some one operate the clutch pedal and watch the operation of the clutch arm in the bell housing. If it works when the foot is going down but doesn't work when the pedal is coming back up then I would suspect the clutch master cylinder is faulty.. It is an easy check and it will save money because the only other thing is a worn out clutch plate and that means box out and new clutch kit fitted.

Jan 11, 2014 | Cars & Trucks

1 Answer

Clutch doesnt work,has new clutch and master cylinder.pushes down and doesnt return up.


the problem is most likley a bad clutch slave cylnder or bad clutch master cyl. or you have air inline

Jul 05, 2012 | 1983 Nissan 280ZX

1 Answer

After changing transmission and clutch in 91 Wrangler, clutch goes to floor. Tried bleeding line but didn't work.


The clutch should go to the floor =) But if it's not disengaging the clutch disk, there's definitely a problem between the pedal and the clutch disk. I'm guessing you have a hydraulic clutch?

Apr 19, 2012 | 1991 Jeep Wrangler

1 Answer

92 mazda miata new clutch new clutch master cylinder systems been bled several times clutch will work 4 awhile park car then try again and clutch quits working again, while driving clutch works fine 4...


Sounds like the seal in the new clutch master cylinder. I've seen that same problem in the hand brake system in small 2 and 4 seat airplanes. ( I'm and aircraft mechanic) The problem is not air in the lines so bleeding won't help. The piston seal is intermittantly failing to seal. That is whty the function can return without any apparent reason as the seal has seated itself. The only cure is to replace or rebuild the master cylinder. ( Yes, even new or rebuilt ones can have a defective or improperly installed piston seal)

Hope this helps

Aug 11, 2010 | 1997 Mazda MX-5 Miata

1 Answer

Replaced master and slave clutch cylinders but


if you replace and shure to make a good bleed on clutch fluid, then replace clutch disc

Jul 27, 2010 | 1991 Toyota 4Runner

1 Answer

Clutch was working but had to pump up to make work after sitting for a time and now wont pump up. clutch is not working now.


Hi, there seems to be a problem with the hydraulic clutch actuators, you should checkt the hydraulic cylinder driven by the clutch pedal for operation. If this cylinder is working, the problem hast to be the other cylinder operating the clutch.

Jun 25, 2010 | 1990 Chevrolet K1500

2 Answers

Clutch Problem


Check your Master Cylinder

Jul 15, 2008 | 1984 Pontiac Fiero

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...