Question about 2000 Ford Expedition

1 Answer

2000 Ford Expdn. My wife just had a 1.35" (l) x 13/64" (d) pin drop from the steering column. One end is tapered, the other is ratcheted? Now the gear selector is functional but sloppy. Took apart the trim to visualize, but can't determine where it came from. Thoughts?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,187 Answers

The pin might be for the gear selector. The gear selector end inside the steering column has a pin that engages for every gear sort of locks it in place. It should be close to where the selector pivots.

Posted on Apr 05, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove a steering wheel off my 1964 Ford Thunderbird


Remove the center horn pad assembly and remove nut holding steering wheel to column. You need a steering wheel puller to remove it from the tapered shaft once the nut is loose. You can rock the steering wheel and pull if you don't have a puller but when it lets go watch for a broken nose.

Apr 12, 2015 | Ford Thunderbird Cars & Trucks

1 Answer

How to remove lock cylinder and key on a 2000 ford e150


You turn the key to the run position. Under the steering column by the key you will see a small hole. You have to use that hole to reach the release pin on the column. Push pin and pull out cylinder and key.

Nov 27, 2012 | Ford Crown Victoria Cars & Trucks

1 Answer

Does the stearing column adjust?


I've never heard of that problem. But racers have to disable those steering wheel locks, so if you like, I'll talk you through it.

The way the lock works is that a pin is forced up through the steering column from underneath. The pin is at the end of a little hinged flap, and a spring pushes this flap up towards the column. When the key is removed, the flap is freed, and the spring pushes it upwards. So, all you need to do is remove the spring. That way, gravity wins, and the pin never gets pushed upwards into the column.

Removing the spring is not that hard, really. You don't even need to remove the steering column trim. Under the center of the steering column, at the end of the ignition switch, you'll find a rectangular metal piece. Drill a 3/8" hole right smack dab in the middle of it. If you aligned the drill right, a spring will fall out of the hole (or maybe just get wound up on the drill bit). Once you remove the spring, the little flapper that sticks up into the steering column to lock it should be allowed to drop, and your steering will unlock.

Of course, yours is already stuck for some reason, so I can't guarantee that removing the spring will allow the pin to fall out from the steering column. If necessary, I suppose you could try to insert a screw into the flap through your new hole, and then use the screw head to try to pull the flap down.

Good luck!

Jun 20, 2012 | 1997 BMW Z3 Roadster

2 Answers

Okay, my boyfriend owns a 2000 ford f-250 super duty and your prolly wondering as to why im asking about this instead of him ... well im more mechanically inclined then he is lol funny huh... okay heres...


It sounds like the shift tube bushings are worn out. There are usually 2 u shaped clamps that have nylon bushings that hold the shift tube to the steering clumn. If loose, that throws off the shift position, could be btween 2 gears at once, and throws off the park - neutral safety switch. Fix that first.


snorkelbobby_53.gif Item Part Number Description 1 14A664 Air Bag Sliding Contact 2 3530 Upper Steering Column Shroud 3 3518 Steering Column Bearing Sleeve 4 3517 Steering Column Bearing 5 3511 Steering Column Lock Cylinder Housing 6 13K359 Multi-Function Switch 7 N808114 Pin 8 N805857 Steering Column Release Lever Pin 9 3D544 Steering Column Release Lever 10 3F609 Tilt Wheel Handle and Shank 11 7361 Column Shift Selector Lever Plunger 12 7210 Gearshift Lever 13 3D657 Steering Column Shaft 14 7B071 Transmission Control Selector Lever Plunger Spring 15 7G357 Gearshift Lever Pin 16 7212 Transmission Column Shift Selector Tube 17 N806582 Tilt Column Pivot Screw 18 7C464 Transmission Control Selector Lever Spring Clip 19 7E400 Gearshift Tube Bushing Clamp 20 - Spacer (Fixed Column) 21 3E729 Steering Shaft (Fixed Column) 22 3F527 Lever Assembly (Manual Transmission) 23 3F530 Pin (Manual Transmission) 24 3F752 Brake Shift Interlock Solenoid 25 7335 Gearshift Lever Socket Bushing 26 7A216 Transmission Shift Selector Position Insert 27 7302 Transmission Selector Lever Arm and Support 28 7E395 Shift Cable and Bracket 29 7210 Gearshift Lever 30 3E691 Steering Column Shift Lock Pawl 31 7W441 Gearshift Lever Pin 32 3676 Steering Column Instrument Panel Bracket 33 3D681 Steering Column Lower Bearing Retainer 34 3517 Steering Column Bearing Sleeve 35 3L539 Steering Column Bearing Tolerance Ring 36 3C674 Steering Column Lower Bearing Spring 37 3C131 Sensor Ring 38 3518 Steering Column Bearing 39 N806423-S56 Steering Column Retaining Nuts 40 14A163 Wiring Harness Retainer 41 3F723 Steering Actuator Housing 42 3B663 Steering Column Lock Lever Pin 43 11572 Ignition Switch 44 3D655 Steering Column Position Spring 45 3D653 Steering Column Locking Lever (LH) 46 3B768 Steering Column Position Lock Spring 47 3B662 Steering Column Locking Lever (RH) 48 3E715 Lower Steering Column Lock Actuator 49 3E696 Steering Column Lock Spring 50 3E691 Steering Column Shaft Lock Pawl 51 3E723 Upper Steering Column Lock Lever Actuator 52 3E695 Steering Column Lock Cam 53 3D656 Steering Column Tilt Flange Bumper 54 14A163 Wiring Harness Retainer 55 391727-S304 Shroud Screws 56 3530 Steering Column Shroud 57 3E717 Steering Column Lock Gear 58 3E700 Steering Column Lock Housing Bearing 59 3C610 Bearing Retainer 60 11582 Ignition Switch Lock Cylinder 61 3L539 Steering Column Tolerance Ring 62 3520 Steering Column Upper Bearing Spring 63 3C610 Snap Ring

Apr 05, 2011 | 2000 Ford F250 Super Duty Crew Cabs

1 Answer

I have a 1988 f-350 diesel and i have lost my key and bought it without a spare how do i remove the ingnition with out a key


You don't without ruining it. I suggest you get a locksmith to make you a new key they can get in there somehow and make a key. In 1988 did Ford use a seperate key for doors? If the doors are the same or the glove box those locks are easier to remove. Also, I've never tried this with a Ford but on newer GM cars if you take the title to a dealer they can make a key from the (VIN) serial number. But, you have to have the title to prove ownership of the vehicle. I don't know if they can do that on an 88 or not. Good luck.

Feb 09, 2010 | 1988 Ford F 350

1 Answer

How to remove key unit from steering column 1986 F150 Ford


COUTESY OF EXPERT "C17HYDRO"
With Key
  1. Disconnect the battery ground.
  2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
  3. Remove the trim shroud halves.
  4. Unplug the wire connector at the key warning switch.
  5. Place the shift lever in PARK and turn the key to ON.
  6. Place a 1/8 in. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
  7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
  8. The remainder of installation is the reverse of removal.

This section is for a NON-TILT with no key or non-functioning cylinder:
Fixed Columns
  1. Disconnect the battery ground.
  2. Remove the steering wheel.
  3. Remove the turn signal lever.
  4. Remove the column trim shrouds.
  5. Unbolt the steering column and lower it carefully.
  6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
  7. Remove the turn signal switch.
  8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
  9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
  10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
  11. Upon reassembly, the following parts must be replaced with new parts:
    • Flange
    • Lock cylinder assembly
    • Steering column lock gear
    • Steering column lock bearing
    • Steering column upper bearing retainer
    • Lock actuator assembly
  1. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the vehicle starts only in PARK and NEUTRAL.

This section is for TILT and no key or non-functioning cylinder:

Tilt Columns
  1. Disconnect the battery ground.
  2. Remove the steering column shrouds.
  3. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Cover the entire circumference of the casting. Cover the seat and floor area with a drop-cloth.
  4. Pull out the hazard switch and tape it in a downward position.
  5. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button.
  6. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch.
  7. Using a 1/8 in. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/2 in. (12.7mm).
  8. Tilt the column to the full down position. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder.
  9. Using a 3/8 in. drill bit, drill down the center of the ignition lock cylinder key slot about 13/4 in. (44mm), until the lock cylinder breaks loose from the steering column cover casting.
  10. Remove the lock cylinder and the drill shavings.
  11. Remove the steering wheel.
  12. Remove the turn signal lever.
  13. Remove the turn signal switch attaching screws.
  14. Remove the key buzzer attaching screw.
  15. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring.
  16. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. The removal of the casting cover will expose the upper actuator. Remove the upper actuator.
  17. Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.
  18. Clean all components and replace any that appear damaged or worn.
  19. Installation is the reverse of removal. Check for proper operation.

Nov 23, 2009 | 1986 Ford F150 SuperCab

1 Answer

How to replace ignition lock cylinder on 1984 Ford F-150 pickup?


With Key
  1. Disconnect the battery ground.
  2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
  3. Remove the trim shroud halves.
  4. Unplug the wire connector at the key warning switch.
  5. Place the shift lever in PARK and turn the key to ON.
  6. Place a 1/8 in. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
  7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
  8. The remainder of installation is the reverse of removal.

This section is for a NON-TILT with no key or non-functioning cylinder:
Fixed Columns
  1. Disconnect the battery ground.
  2. Remove the steering wheel.
  3. Remove the turn signal lever.
  4. Remove the column trim shrouds.
  5. Unbolt the steering column and lower it carefully.
  6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
  7. Remove the turn signal switch.
  8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
  9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
  10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
  11. Upon reassembly, the following parts must be replaced with new parts:
    • Flange
    • Lock cylinder assembly
    • Steering column lock gear
    • Steering column lock bearing
    • Steering column upper bearing retainer
    • Lock actuator assembly
  1. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the vehicle starts only in PARK and NEUTRAL.

This section is for TILT and no key or non-functioning cylinder:

Tilt Columns
  1. Disconnect the battery ground.
  2. Remove the steering column shrouds.
  3. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Cover the entire circumference of the casting. Cover the seat and floor area with a drop-cloth.
  4. Pull out the hazard switch and tape it in a downward position.
  5. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button.
  6. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch.
  7. Using a 1/8 in. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/2 in. (12.7mm).
  8. Tilt the column to the full down position. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder.
  9. Using a 3/8 in. drill bit, drill down the center of the ignition lock cylinder key slot about 13/4 in. (44mm), until the lock cylinder breaks loose from the steering column cover casting.
  10. Remove the lock cylinder and the drill shavings.
  11. Remove the steering wheel.
  12. Remove the turn signal lever.
  13. Remove the turn signal switch attaching screws.
  14. Remove the key buzzer attaching screw.
  15. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring.
  16. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. The removal of the casting cover will expose the upper actuator. Remove the upper actuator.
  17. Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.
  18. Clean all components and replace any that appear damaged or worn.
  19. Installation is the reverse of removal. Check for proper operation.

Oct 13, 2009 | 1984 Ford F 150

1 Answer

Need an digram of 2000 ford focus power steering pump


cfef959.gif
Item Part Number Description 1 - Steering wheel 2 - Steering column 3 - Boot 4 - Tie-rod 5 - Tie-rod end 6 - Steering gear 7 - Steering gear to fluid cooler hose 8 - Fluid cooler 9 - Power steering pressure (PSP) switch 10 - Power steering pump 11 - Fluid supply hose 12 - Fluid reservoir 13 - Pump to steering gear pressure line 14 - Steering gear pinion extension

Jul 30, 2009 | 2000 Ford Focus

1 Answer

2000 F150 gear shift knob no longer shifts gears


Good day
No the steering wheel don't need to be remove.
1. remove the instrument panel cluster opening finish panel assembly. remove the 3 screws that retains the upper steering column shroud and remove cover.
2. insert a scratch awl into the access hole on lower steering column shroud and push in the ignition lock cylinder release pin. insert the ignition key into the lock, turn ignition to run position and remove the lock cylinder from the steering column. remove lower steering column shroud. unsnap and slide gearshift lever boot up toward end of gearshift lever.

NOTE: ALWAYS INSTALL NEW GEARSHIFT LEVER RETAINING PIN DURING REASSEMBLY

3. remove gearshift lever retaining pin by lightly tapping with a drift punch and hammer. disconnect gearshift lever harness connector. remove gearshift lever. to install reverse removal procedure.

hope this helps

Cheers

Jul 15, 2009 | 1993 Ford F150 SuperCab

2 Answers

Drivers side rear turn signal and brake light not working


I've noticed the same problem with my 2001 Ford Exployer Sport Trac. When my girlfriend drives my truck she raises the steering column, and when I'm driving, I lower the column. I noticed when I was driving recently the left front turn signal kept flashing quickly, thought it was the bulb, but changed and still happening. Today I took apart the steering column cover and noticed the wiring for the turn signals and hazards were loose. To fix this problem I pulled the wires out of column more as to not stress the connection. So far this has fixed the problem.

Dec 14, 2008 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...