Question about 2003 Nissan Altima

Open Question

I have a 2003 Altima with a Bose sound system, but the head unit does not have the DIN port. Does anyone know if it is possible to install one into the current PY540 deck? If not, what would be my best route? I'm thinking finding a 2002 model with the DIN port...the reason for doing this is to get an AUX input

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

autodr
  • 260 Answers

SOURCE: 2002 Altima Factory Bose Audio ERR3

there are only couple options. pull radio and send to shop for repair, purchase used radio from good junk yard. or call dealer and see if there is a warranty on it. even though its 6 yrs old they may help. what they do at the dealer is an exchange

Posted on Nov 16, 2008

unvme
  • 266 Answers

SOURCE: Aux cable stuck in Aux input

needdle nose plyers or you can use a screw just turn and pull

Posted on Jan 25, 2009

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 92 Answers

SOURCE: i checked head light lamp on 2003 altima it's

headlights should be on same fuse. fuse box should be located in engine compartment

Posted on Sep 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to connect kenwood ddx371 to my 2003 nissan 350 with bose without navigation?


you need a double size DIN , this is the size of the radio location , an ordinary radio is just DIN , so space needs to be twice the size of radio , there is usually a wiring adaptor available so that connection of aftermarket devices is made easy , any good auto spares shop should have these , then just remove the unit in care and follow the instructions with the kenwood

Nov 08, 2014 | Cars & Trucks

1 Answer

2007 Nissan Altima Stereo Wiring Diagram for Bose Navigation


None are actually color coded. The schematic has the wire colors on it next to the wire.

May 01, 2014 | 2007 Nissan Altima 3.5 Sedan

1 Answer

I have a 2003 altima 2.5 S. the car ran hot and now it will not crank and i have no idea whats going on. can anyone help


just from your description it sounds like you warp the heads. however does will not crank mean will not run or will not turn over? a more detailed description would help me help you

Nov 17, 2011 | 2003 Nissan Altima

1 Answer

Hi my 2003 nissan altima radio not working no sound coming from speaker yet all light are on


Is it a standard version or Bose version? If it's a standard version then either the plug in the back came loose or the built in amp in the stereo is dying. if it's a Bose, then there should be a pre-amp some where under or behind the dash or possibly under or behind the rear seat/ trunk. In that scenario it's possible that the amp has gone bad. Another possibility regardless what version system is installed would be if a wire cracked and is showing somehow, grounding out causing the speakers to go out. Bad ground. maybe a loose plug behind the stereo. Also has the stereo every been replaced. Is it factory stereo and speakers.

Oct 02, 2011 | 2004 Nissan Altima

1 Answer

2006 NC MX5 Bose 6 stacker replacement/upgrade


Companies like Scosche and Metra make inexpensive dash kits for the Miata that will allow you to use a standard DIN head unit of any kind. They also often make special adapters to allow a standard aftermarket head unit to plug into the special Bose wiring.

Mar 29, 2010 | 2008 Mazda Mx 5 Miata

1 Answer

What size after market in dash dvd can I put in 2003 spyder gs


your radio/dash opening DIN size is what they call double DIN, to get the right unit fopr this u will need to know if you have a Facory Infinity premium sound system, it makes a diff in the model f the in dash units, here is a link to a site that has a selection of in dash DVD players for your double DIN dash.
http://www.crutchfield.com/S-nkinM0jziRR/cgi-bin/autoinfo/autoinfo.asp?id=&vehicleid=14718&vb=Y&TypeCH=&lp=%2Fg%5F168550%2FIn%2Ddash%2DDVD%2DReceivers%2Ehtml%3Ftp%3D20217&sl=Y

Aug 11, 2009 | 2003 Mitsubishi Eclipse Spyder

1 Answer

After Market radio install on a 2001 Passat


Metra makes a preamp harness that you can use if you have the partial Bose system. My A4 had that (where the front speakers were run off of the headunit with speaker-level feed, but the deck put a line level signal to a rear amp to power the speakers). This harness would let you use the aftermarket deck with your factory speakers, if you have the partial Bose system. Best bet is to do a Google search for "Metra 2001 Passat" or something like that and I'm sure it'll show up.

Jul 31, 2008 | 2001 Volkswagen Passat

Not finding what you are looking for?
2003 Nissan Altima Logo

Related Topics:

245 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...