Question about 1994 Ford Ranger Supercab

2 Answers

Serpentine belt came off and it looks like a pulley has broken that is located next to the alternator. As you are looking at the engine from the front, this pulley would be located to the right of the alternator. Need to know what this is called to be able to order. Thanks

Posted by on

Ad

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 46 Answers

You need a serpentine belt and an idler pulley. Very easy fix, that can be done with a basic set of tools. Hope this helps!

Posted on Apr 05, 2011

Testimonial: "Thank you. Very helpful."

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 8,518 Answers

Hi, if it's just a pulley on a bolt and not the tensioner, it's called the idler pulley. I could be more reassuring if you tell me which engine you have.

Posted on Apr 05, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

SERPENTINE BELT


I had a similar problem that turned out to be some bad rubber bushings on the alternator mounting bolt. The alternator would shift from side to side causing misalignment with the serpentine belt. To check this, you will need to remove the serpentine belt and take a close look at those bushings. If they are original equipment, I would change them out. In my case, everything lined up fine, but with the engine running, the alternator would shift position and shred the serpentine belt. Good luck.

Jan 07, 2013 | 1994 Plymouth Voyager

2 Answers

I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How simple is it to change a alternator belt on subaru svx?


    1. Removing the Serpentine Belt
      • 1 Park your Subaru on a level surface and open the hood.
      • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
      • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
      • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
      • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
      • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
      • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
      Installing the New Serpentine Belt
      • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
      • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
      • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
      • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
      • 5 Slide the serpentine belt onto the tensioner pulley.
      • 6 Release the tensioner pulley back into position.
      • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
      • 8 Connect the ground (black) battery cable using the wrench.

    Oct 18, 2011 | 1992 Subaru SVX

    1 Answer

    Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


    Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    How do i release the tension belt ... cant seem to find bolt being referred to in other docs


    Here's the procedure on how to release and replace the tension belt of your car.

    Step 1
  • Open the hood on the Volvo S-60 and find the serpentine-belt routing diagram. The diagram should be attached to the top of the fan shroud that covers the radiator. If not, draw out the exact routing method of the serpentine belt around each pulley with a pen and a piece of paper.
  • Step 2 Locate the serpentine-belt tensioner that is in the very center of the engine. The tensioner will have a square bolt head in the center of the tensioner pulley.
  • Step 3 Slide the open end of the 5/8-wrench onto the square bolt head in the center of the belt-tensioner pulley. Turn the tensioner pulley counterclockwise and slide the serpentine belt off of the tensioner pulley.
  • Step 4 Remove the serpentine belt from the other pulleys and pull the belt out of the engine compartment.
  • Step 5 Slide the new serpentine belt into the engine compartment and around the crankshaft pulley.
  • Step 6 Route the new serpentine belt around each pulley. Turn the belt-tensioner pulley counterclockwise again and slide the serpentine belt around the tensioner pulley. Release the tensioner and it will tighten the belt around the pulleys. Look over the belt to ensure that it is inside of each pulley.
  • Step 7 Crank the S-60 and look over the serpentine belt with the motor running. Let the engine run for about one minute and shut the engine off. Close the hood.
  • Aug 12, 2010 | 2001 Volvo S60

    3 Answers

    Volt light is on


    Your lucky you didn't hydro lock the engine. You probably shorted the alternator and its not putting out amps needed to operate most accessories on the vehicle (like power steering pump). Have the charging system checked out. Replace the items the repair shop tells you to replace.

    Jul 19, 2010 | 1998 Buick Park Avenue

    2 Answers

    Is the idler pulley what sets the tension on the serpentine belt


    yes and that's how you change the belt also. just turn it with a wrench to loosen it if you want to change the belt.

    Dec 18, 2009 | 1996 Dodge Caravan

    1 Answer

    How do I replace a broken alternater belt on a 2003 mitsubishi lancer


    First pop the hood and find the serpentine and alternator belts on the left side of the engine compartment. The serpentine belt runs around four pulleys. The alternator belt uses two pulleys. They share space on the drive shaft so they are right next to each other.
    Of the four pulleys using the serpentine belt, three of them are vertically in line (closer to the front of the car) and the fourth stands alone (closer to the cab). Of the three vertically in line, the middle pulley is the one used to adjust the tension on the belt.
    You must first break loose the bolt in the center of the tension pulley (the bolt is facing the passenger tire) by turning it counter clockwise. Then leave that bolt and go to the bolt connected frame connected to the other side of the tension pulley (this bolt is facing the front of the car). Turn that bolt counter clockwise until the serpentine belt is loose enough to pull off. Replace the belt and tighten in the opposite order. Once the desired tension is reached, crank the car and run it for a few minutes. Finally cut the car off and check the tension, tighten or loosen as neccessary.

    Oct 10, 2009 | 2004 Mitsubishi Lancer

    1 Answer

    1995 Jeep Grand Cherokee - Removing serpentine belt


    Faceing the Engine The Tentioner is on the LEFT side next Pulley Down from the Alternator , Use A Box end 6 point Wrench to Turn Tentioner To the Right (CLOCKWISE) to Loosen the Belt, Take A Good Look at it If there is No Belt Diagram to Remember the Way It is Routed if thats all you need then you R on your way. Good luck !

    Feb 05, 2009 | 1995 Jeep Grand Cherokee

    Not finding what you are looking for?
    1994 Ford Ranger Supercab Logo

    120 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    fordexpert

    Level 3 Expert

    5537 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...