Question about 2002 Lexus RX 300

1 Answer

My high mount break light will not work i replaced the bulb and it still does not work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,915 Answers

The first place to start is the connector for the harness, probably under the package shelf in the trunk-look there to see if it has been accidently disloged. If not, make sure the wiring has not been damaged, lots of 'pinch' areas in the trunk-hope this helps

Posted on Apr 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse is for the Brake Lights on a 98 Mercury Mountaineer. It is NOT listed on the Diagram fir the Interior Fuse Box !!


They're part of the turn light fuse. Replace the turn signal switch. All exterior lights run threw it, except the high mount brake light.

Jul 21, 2015 | Mercury Cars & Trucks

1 Answer

How to change high mount brake light bulb in a 2002 lincoln navigator


Instructions
    • 1 Open one of the rear doorsicon1.png of the LS. Position yourself on your knees in the back seat, facing the rear deck or rear dash.
    • 2 Remove the cover from the high-mount brakeicon1.png light assembly, by hand. Pull the cover toward the front of the vehicle. Do not pull extremely hard, or you will break the clips that mount through the deck from the trunk.
    • 3 Pull the old light bulbsicon1.png out of the high-mount assembly. Wrap the new bulbs in a paper tower prior to picking them up. Insert new bulbs into the assembly, by hand. Do not touch the bulb lenses with your hands directly.
    • 4 Install the high-mount cover onto the rear deck and push the cover toward the rear glass to lock it in place.


Read more: http://www.ehow.com/how_10060583_replace-upper-brake-bulb-2001-lincoln-ls.html#ixzz30cNQ559F

May 03, 2014 | Cars & Trucks

1 Answer

1998 buick century high mount brake light doesn't work, bulbs have been replaced


there is a seprate ground that mounts to the frame of your car near the light usualy in trunk in between the rear speakers locate and make shure the conection is good.if that dos not solve it on the pasengers side rear light check bulbs for detereated ends if thay are then replace.this shuold solve you problem

Jan 19, 2013 | 1998 Buick Century

1 Answer

I was told by a local car shop that in order to fix the High Mount Brake Lamp (brake light is out) that I would need to replace the entire unit. One year ago it cost me $172.03 to replace the entire unit....


check to see if you got two screws if you do all you need is the light bulb if you still have the old one look at it and see if the bulb can be replace without breaking anything i no you mention a year ago

Sep 24, 2012 | 2005 Ford Taurus

1 Answer

98 dodge 1500 no brake lights changed switch, bulbs,checked wiring for breaks ,


if no brake lights are working including the high mount then you may want check the brake light switch. if the high mount light works then you may want to check the turn signal switch.

Jul 27, 2011 | 1994 Dodge Ram

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

1 Answer

1999 GMC Envoy: replaced both GE 3057 lamps in left rear light assembly. Lamps both light. However depressing brake pedal does not initiate brake light. The righ rear brake light does work. The high mount...


The high mount brake light has its own fuse, so check that first. The high mount bulb is generally a stabdard type (there may be more than one bulb) or you can replace with an LED. As for the left rear bulbs not working when depressing brake pedal, check the bulbs again for any spring that may be broken. If the bulbs are still good, make sure there is sufficient contact with the socket. If still not working, have someone check it out further.

Feb 15, 2010 | 1999 GMC Jimmy

1 Answer

I have 1997 explore eddie bauer ed. V8 awd. The computer indicated that "check break light" but my break light working just fine. I think it may have to do with the wiring problem. What can I do?


you may have a poor connection where the bulb contacts the wiring. clean all bulbs and sockets. Also, check the high mount stop lamp too.

Feb 03, 2010 | 1997 Ford Explorer AWD

1 Answer

Tail break lights don't work. Window break light does work however. Bulbs have been replaced.


Check the brake light fuse. The high mounted brake light (third brake light) is on a different circuit than the brake lights. Hope this helps.

May 23, 2009 | 1998 Mercury Mystique

1 Answer

Break lights


check for shorts or broken wiring at the 3rd brake light housing and pigtail.

Jun 19, 2008 | 2002 Ford Escort

Not finding what you are looking for?
2002 Lexus RX 300 Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

905 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...