Question about 2002 Suzuki Grand Vitara

Open Question

How do I install new rear door vent glass? - 2002 Suzuki Grand Vitara

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install quarter window that flips out on 2003 dodge Dakota. 2 door.right side


REMOVAL

(1) Remove quarter trim panel.

(2) Remove the bolts attaching the latch to the cab


side panel.



(3) Remove the nuts attaching the frame/hinge to

the B-pillar.

(4) Remove the glass from the cab.
(5) If necessary, remove the latch from the glass.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

INSTALLATION

(1) If removed, install the latch to the glass.

(2) Center the window glass at the opening, insert

the hinge studs in the B-pillar holes, and install the

nuts.

(3) Attach the latch to the rear side panel with the

bolts. Tighten the bolts with the latch in the lock

position and pushing rearward on the latch.

(4) Test the vent window for water leaks.
(5) Install quarter trim panel.

Oct 02, 2016 | 2003 Dodge Dakota

1 Answer

Replace vent glass


It is easiest if you remove the door panel and passenger glass first. Once that is done it is much easier to remove the weather stripping, seal and vent window.

Dec 26, 2013 | 1998 Ford Expedition

1 Answer

1998 ford explorer rear window removal


Hi there:

  1. Remove the door trim panel and speaker if applicable.
  2. Remove the screw from the division bar. Remove the inside belt weatherstrip(s) if equipped.
  3. Remove the 2 vent window attaching screws from the front edge of the door.
  4. Lower the glass and pull the glass out of the run retainer near the vent window division bar, just enough to allow the removal of the vent window, if equipped.
  5. Push the front edge of the glass downward and remove the rear glass run retainer from the door.
  6. If equipped with retaining rivets, remove them carefully. Otherwise, remove the glass from the channel using Glass and Channel Removal Tool 2900. Remove the glass through the belt opening if possible.

To install:
  1. Install the glass spacer and retainer into the retention holes.
  2. Install the glass into the door, position on the bracket and align the retaining holes.
  3. Carefully install the retaining rivets or equivalent.
  4. Raise the glass to the full closed position.
  5. Install the rear glass run retainer and glass run. Install the inside belt weatherstrip(s).
  6. Check for smooth operation before installing the trim panel.



Hope this helps.

Feb 28, 2013 | 1998 Ford Explorer

1 Answer

We accidently had the door shut on my friends 95 fork truck, and the keys were still in ignition. We had to break the ventglass window, how do we replace that? window


1st. Remove door trim panel by removing the screw retaining the armrest section of the trim panel to the door inner panel and remove armrest.
2nd. Remove the screw retaining inside door handle and remove the handle.
3rd. On vehicles with manual operated window cranks remove the screws retaining the crank, then remove the crank and washer.
4.th On vehicles with power windows, remove the power window switch panel by inserting a thin blade screwdriver between the bezel abd the trim panel, at either side of the bezel. Then carefully pry the bezel from the trim panel and the housing assembly will snap out. Remove the retaining screws from the bottom side of the connector and remove the switch assembly from the connector.
5th Remove door lock control knob on models rquiped with.
6th On models with power door locks, remove the switch housing assembly from the panel by inserting thin blade screwdriver into the spring tab slot located at the top and bottom of the switch housing. Apply pressure and the assembly will pop out. Disconnect the housing from the wirring assembly connector by separating the lock fingers.
7th. If equipped with power outside rear view mirror, remove the switch housing bezel by removing the two retaining bezel nuts and the bezel.
8th. Remove the screw retaining division bar to inner door panel.
9th.Remove the screws retaining vent window assembly to the leading edge of the door.
10th. Lower the door glass to the bottom of its travel.
11th. Pull the glass run out of the upper run retainer next to the vent window division bar. Pull the glass run out just far enough to allow the vent window assembly to be removed.
12th Tilt the vent window and the division bar assembly toward rear of the door. Carefully guide the assembly up and out of the door.
13th. Remove the two upper pivot-to-vent frame screws.
14th. Remove the retaining nut and tension spring from the vent vindow lower oivot.
15. Separate the vent glass retainer and the pivot stops from the vent frame and weatherstripping assembly.
16th. Installation is reverse of the removal procedure. The pivot tension spring should be adjusted so the vent will remain open at higway speeds. Be sure the front door window spacer is in place when installing the vent window and division bar assembly.

I know it is hard to picture it but this is best I can explain with out picture.

Feb 23, 2010 | 1995 Ford F150 Styleside Regular Cab

1 Answer

How do I remove and install a rear passenger side window (manual) in a 1997 Saturn SL1?The window was smashed, and I need to replace it. Thank you so much for your time and help!


Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.
To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.
  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.
cc80642.jpg

Fig. 1: Remove the glass nuts using a suitable tool-front door shown

8ca6a10.jpg

Fig. 2: Exploded view of the regulator mounting-except rear door

b18d064.jpg

Fig. 3: Exploded view of the rear door regulator mounting

0b9470a.jpg

Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.


Oct 16, 2009 | 1997 Saturn SL

1 Answer

How do you replace a drivers side window on a 1992 Saturn



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.


To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.

  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.

PICTURES ON NEXT POST!

Oct 13, 2009 | 2000 Saturn Ls 4dr Sedan

1 Answer

How get replacement rear vent window into place? its a 1995 maxima passenger side rear vent window.have picked up a new one from salvage and fear if i force it, it may shatter.


The metal glass run between the vent & doorglass has a phillips screw at the top under the door weatherstrip. I usually remove that screw, with the doorglass down & glass run (felt) pulled down at the top just enough to allow the metal part to move as you force the ventglass into place. lube the vent gasket with silicone spray or any good wet lubricant and force the glass in, bottom 1st. If this makes you too anxious, remove the 10 mm attachment that retains the metal glass run at the lower end of the part. To get to it, you will have to remove the door panel. Good luck

Sep 27, 2009 | Nissan Maxima Cars & Trucks

2 Answers

Need to replace a broken window on rear passenger 1999 jeep chero


This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Sep 09, 2009 | 1999 Jeep Grand Cherokee

3 Answers

Hey when i push the power botton for the rear window it doesn't go down,I checked the power button,and its good ! Can i replace the power motor in the rear window,and where is it located,i would like to...


  1. Raise and support the rear door window glass to the full up position.
  2. Remove the interior door handle.
  3. Remove the rear door speaker.
  4. Remove the water shield.
  5. Disconnect the rear door window regulator motor electrical connector.
  6. Remove the rear door window regulator rivets.
  7. Remove the rear door window regulator by sliding the regulator arms off of the window glass track.
  8. Installation is the reverse of the removal procedure, noting the following:
    • Cycle the door glass to make sure of engagement of the drive mechanism.
    • Remove the rear door window glass-to-regulator bolt or rivet.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet.
    • Secure the rear door window glass in the full UP position with tape.
    • Disconnect the window regulator motor electrical connector.
    • Remove the 2 window regulator nuts.
    • Remove the 3 window regulator motor bracket nuts.
    • Install the window regulator assembly. Tighten the 3 motor bracket nuts to 89 inch lbs. (10 Nm).
    • Install the 2 window regulator nuts. Tighten the nuts to 89 inch lbs. (10 Nm).
    • Connect the window regulator motor electrical connector.
    • Remove the tape securing the rear door window glass in the full UP position.
    • Position the rear door window glass as necessary to access the rear door window glass-to-regulator rivet. Tighten the bolt to 62 inch lbs. (7 Nm), or install a new rivet.
    • Install the window regulator motor
    • Remove the window regulator assembly.
Remove the window regulator motor

Feb 23, 2009 | 2001 Ford Explorer

1 Answer

Cadillac Door Glass


I did look it up and I only see one part for the 94-99 vent glass for the rear door.

Nov 15, 2008 | 1996 Cadillac DeVille

Not finding what you are looking for?
2002 Suzuki Grand Vitara Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...