Question about 1993 Honda Accord

1 Answer

Rotor and spindel will not come off even with a pulley which broke off a piece of the rotor

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

... i'm sorry to say this, but, it's a 4hr job. you need to remove the hub and bearing assembly to remove the rotor...

Posted on Apr 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing Crankshaft Pulley with Bolt, I hammered on the Pulley to help seat, rotating the Crank by hand hear a clicking sound?


You should never use impact guns or a hammer on any crank or camshaft. You may have broke it in pieces inside.

Jun 07, 2017 | Cars & Trucks

2 Answers

2004 Kia crank bolt broke off on hiway why


without seeing the damage directly, it would be difficult to say. however, it could have been a faulty harmonic balancer that failed, causing the bolt to shear off or even simple metal fatigue.
either way, it will be an expensive repair

Jan 06, 2015 | 2004 Kia Sorento

1 Answer

CAMTIMMING MARKS PLEASE ENGINE 160 A


YOU GOT A PLASTIC COVER BEHIND CAM PULLEY THERE IS A PIECE YOU MUST LIFT UP AND ALIGN MARK ON CAM PULLEY AND ON CRANK NEED TO LINE MARKS ON TDC AND ROTOR ON NO 4

Oct 01, 2013 | 1989 Fiat Uno 1.4

1 Answer

96 cherokee auotmatic transmissiom will not down shift


The crank pulley. is the drive pulley and it is in two pieces separated by rubber to dampen out vibrations. Below bottom rotor.----------------------------------------------------------------------------------
Renault CAN Clip

Feb 01, 2013 | 1996 Jeep Cherokee Country

1 Answer

I have a 2006 Ford Taurus. Yesterday the serpentine belt broke and I replaced it. My car was looked at by two men who know a good deal about cars. They both said the reason the belt broke was because...


AC PULLEY AND BEARING CAN BE REPLACED.YOU WILL NEED AC COMPRESSOR TOOLS LIKE SEAL TOOL AND PULLEY BEARING TOOL THE AIR CONDITIONER SYSTEM HAS TO BE DISCHARGED TO FIX AC COMPRESSOR PULLEY AND BEARING. YOUR AC COMPRESSOR PULLEY HAS A NUT AND SNAP RING HOLD IT IN PLACE.GO TO DEALERSHIP TO SEE IF THEY HAVE THE AC PULLEY NUT AND SNAP RING.SOME TIME YOU WILL HAVE TO BUY A NEW AC PULLEY BEARING AND SEAL TO GET A NEW NUT AND SNAP RING.AUTO ZONE HAS AC TOOL YOU CAN RENT TO FIX AC BUT YOU HAVE TO TAKE CAR TO DEALERSHIP AND GET AC SYSTEM DISCHARGED FIRST BEFORE YOU CAN WORK ON AC COMPRESSOR.

Dec 01, 2010 | Ford Taurus Cars & Trucks

2 Answers

HOW DO I KNOW IF MY G20CHEY VAN HAS A BLOWN TIMING CHAIN


I would remove the distributor cap, and turn the crankshaft pulley while watching the rotor to see if the rotor turns.

Oct 27, 2010 | 1989 Chevrolet G20

1 Answer

2002 1500 4 x 4 Replacing front wheel bearing hub; can't get to the 3 bolts


to start with, that is not a u-joint cover, it is a cv joint. if this is a chevy. you will have to pull the cv shaft out of the spindel. first loosen the outter tierod nut on the spindel, do not take off completely but just so its on finger tight. get a large hammer and hit the spindel right where the tierod goes through it. a couple of good shots and it should drop out take off nut and move outter tierod aside. now you are gonna do the same thing to the lower ball joint. only when your ready to hit that part of the spindel where the ball joint goes through get a prybar under the upper controll arm and get a budy to push up on it. as long as the shock is still bolted on your in no danger. pull the spindel out towards you from the bottom and you will have enough room to pull the shaft out of spindel to get the nuts. you might have to put ball joint back in without shaft in place to hold spindel still to break those bolts loose. make sure you use new cotter pins on ball joint and tierod nuts

May 30, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
1993 Honda Accord Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...