Question about 1989 Oldsmobile Cutlass Supreme

1 Answer

1989 oldsmobile cutlass supreme front drivers side ball joint replacement

Recently I replaced my rotar and lug studs after while moving it off a trailor I noticed greasy goop coming out and the ball joint was completely broken off how do I replace this?

Posted by on

  • Anonymous Mar 27, 2014

    upper ball joint replacement

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 421 Answers

You can buy a new lower control arm but the cheaper way out is you can buy a new ball joint for about $15 and cut off the rivits holding the old one and bolt on the new one in place with the supplied hardware hope this helps also a airhammer make quick work of rivits please rate -jeff

Posted on Sep 01, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Am replacing ball joint - is it spring loaded etc.


NO the spring is on the strut the only tension you will havt to deal with is when trying to pull down on the lower A arm to remove ball joint stud from the steering knuckle. the front sway bar goes in the underside of the A arm and this causes upward tension on the A arm.

Sep 27, 2009 | 1992 Oldsmobile Cutlass Ciera

1 Answer

Cutlass Supreme new front wheel bearing repeatedly goes out


You may have pulled the inner tri-pod joint out of the cv shaft and that will make noise. Is the bearing really bad? Does it turn freely?

Jun 23, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Popping sound on diver front tire


I dont work as a car mechanic but have some limited knowledge,,,, Most of the time that you get popping noises in the front end (usually while turning) it is the CV joint,,, the boot drys and cracks and dirt, sand and grit take out the joint, so if you replaced the joint and the boot and lubed it up,,, could be the tire is not completely round(was told my rear tires were shaped like eggs by one shop) other than that, you have to limit it down to the when and wheres... like when does it happen, how fast are you going, stopping,,turning, braking,,, out of gear(in nuetral..etc) then I think the answer will be easily to tell.

May 09, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Shaking while braking


If you put new rotors on and used the old pads that could be your problem. You never put new rotors on, with out new pads even when the old pads look new. Also just because the rotors are new does not mean thery are not warped. I have done a lot of break jobs where i have had to take the rotors back off and had them turned because they were warped right out of the box.

Mar 28, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

1995 cutlass supreme


New driveshaft, ball joint and alignment. might not hurt to have the wheel and tire checked as well.

Mar 12, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Cv joint replacement


Remove the tire and tighten 2 lugnuts onto the brake rotor. remove the axle nut in center of the brake rotor and drive the axle out of the spindle. If the ball joint is original, you have to grind out the rivets on the lower control arm. Remove and replace the ball joint with the hardware included with the ball joint. Next, pry-unsnap the axle end from the transaxle with a prybay and drive-snap in the new axle shaft into the transaxle. reverse to assemle, align front end and wholla! your done. 1 hour,15 min. $115.00 to do it yourself.

Mar 07, 2009 | 1995 Oldsmobile Cutlass Supreme

1 Answer

Broken front lug bolt 94 cutlass surpeme


you can replace the stud by hitting it out with a hammer and punch. by a new stud and nut. put the new stud through the hole to pull it through put the lug nut on backwords and tightening it down until it seats completely.

hope this helps.
please rate good.

Mar 01, 2009 | 1989 Oldsmobile Cutlass Supreme

1 Answer

Ball joint on drivers side broke how do i replace it


With out air tools it will be a pain. You have to grind, chisel, and maybe even drill. Trust me, just take it in. If you still want to know, i'll tell you but I still suggest taking it in....

Sep 17, 2008 | 1994 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
Cars & Trucks Logo

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...