Question about 2008 GMC Sierra 2500HD 2WD

1 Answer

My 4wheel drive made a poping noise when i went to disengage it and immediately said service 4wheel drive is there a fuse or something (it will not work now)

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 77 Answers

Try disconect the batt 4 60 seconds then put it back on that should reset the computer it may stay out

Posted on Apr 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Service a 2009 4wheel drive truck


Encoder motor ,..........................

Mar 09, 2015 | 2009 Chevrolet Silverado 1500

1 Answer

96 explorer disengages 4wh low but does not engage 2wheel


Does it shift to 4wd high range ? If so then shift to 2wd . What is going on here is the transfer case motor is stopping due to the motor position sensor has gone bad which means that you replace the transfer case motor assembly. But if you wish to make it a 2wd for awhile then remove motor and manually turn shaft . This can be done by raising and supporting rear axle truck in park remove motor turn shaft slowly with pliers and rotating the play in drive shaft. There are stamped markings on back of case showing gear positions..

Mar 31, 2014 | 1996 Ford Explorer

1 Answer

2004 chevy tahoe poping noise under front end driver side


is it 4wheel drive if so cv joints if not fan could hitting something

Mar 30, 2012 | Cars & Trucks

1 Answer

4 wheel drive quit at some time didn't know it...drives fine only rear wheels pulling..could it be electrical ??


I hava a 1999 Grand cherokee loredo V8 with full time 4wheel drive. when the rear tires slip I am hearing a poping noise in the front end when the 4wheel drive engages. I was told by one person that it could be the chain in the transfer case slipping but I was told by a jeep salesman that this year jeep did not have a chain. Could this be the CV joints in the front axels?

Jan 11, 2011 | 1999 Jeep Grand Cherokee

1 Answer

I have a 99 Chevy Blazer, I have had it for about six months or so. The past month and a half, it pops out of 2 wheel drive and into 4 wheel drive (sometimes blinking back and forth between 4 hi and 4 lo)....


I have the same trouble. It seems a relay is keeping it in 4wheel drive. I havne't solved the trouble yet. It may be a loose or corroded wire in the connector to the TCCM located in the passenger kick panel. Dealer part about $450 or more. For the moment I took out the fuse for the 4 wheel drive. It is located in the lower right hand side in the fuse the box under the hood. It disengages the 4wheel drive and I replace the fuse if I need the 4wheel drive.

Aug 26, 2010 | 1999 Chevrolet Blazer

1 Answer

2003 wont disengage from 4wheel drive have already tried to drive it in reverse to disengage it


Try this: shift into neutral, wait a few seconds, then try to disengage. If it doesn't work, try again, but turn vehicle off after shifting into neutral, wait about 15 seconds, hopefully that will do it.

Jan 04, 2010 | 2004 Hummer H2

1 Answer

My 1997 chevy blazer does not have a 4wheel drive switch


If there is no switch present then it is full time 4X4, it does not disengage, good for travel bad for fuel mileage.

Sep 08, 2009 | 1997 Chevrolet Blazer

1 Answer

4Wheel and allwheel drive went out...


look for a leaking or broken vacuum line on or near the front differential possibly under the battery you should find a control unit to engage or disengage 4wd

Jan 23, 2009 | 2001 Chevrolet Blazer

3 Answers

1997 Ford F 150 Fuse box diagram


You should be able to pick up a manual on a 97 Ford F150 from any of the major auto stores like Auto Zone, etc


Good luck Loringh

Oct 25, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...