Question about 2008 Suzuki SX4

Open Question

My brake pedal went to the floor only 84 John Deere 410b backhoe. I pump them and it worked. Are they hydraulic? Where do I check the brake fluid? Or are they mechanical? Thanks

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 8071 Answers

SOURCE: intermitent pedal going to floor no fluid loss happens 1week to three 2 pumps brake fine

Master cylinder problem. Or bad brake cylinder. One has bad seals.

Posted on Feb 24, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I check the brake fluid on a 580C?


I am going to have to guess you are referring to a 580 C Case backhoe.
In any case never ever put anything in a brake fluid reservoir but brake fluid, and the right fluid to be sure, or you will seriously damage or destroy the brakes "forever".
The brake fluid reservoir is usually plastic, and often you can see through it just enough to see the level of brake fluid.
It should be located near the front of the brake pedal, and is usually sort of white in color, with a black cap that can be screwed off.
God bless your efforts.

Aug 04, 2016 | Cars & Trucks

1 Answer

Intermittent loss of brake pedal,only happned three times but customer says it went to the floor


If this is a hydraulic brake system, the first thing to do is to check the brake fluid level in the reservoir. Assuming that it is not down, the problem will probably be in the master cylinder. Try pushing the brake pedal down very slowly. This will not put a lot of pressure on the seals in the master cylinder, and if there is a problem, the brake fluid will leak past the seal allowing the pedal to go slowly to the floor. If you push the brake pedal down rapidly, the pressire on the seal will hold it against the master cylinder wall, and the brakes will hold fine.
If the fluid level in the reservoir is low, look at all of the wheels and slave cylinders to see if you can locate a leak. I don't suspect a leak based on your description of the problem, but it's worth checking.

Apr 04, 2015 | Mitsubishi Cars & Trucks

3 Answers

Are there vacuum hose on the brakes hydraulic system?


NO. the vacuum is used to make the brake pedal easy to push, power brakes. the pedal would be hard without vacuum, that is why the pedal gets hard with the key off and engine not running. the problem you are having is more of a hydraulic problem.
Have the brakes checked asap. the brake system may have a leak causing the pedal to go low. check the fluid level and if it is low or empty then there is a problem, could be a rotted brake line leaking or a wheel cylinder leaking.

Dec 07, 2012 | 1997 Ford Probe

2 Answers

Truck wont stop,brake pedal goes to floor, hydroboost, steering pump, replaced


This sounds like a bad master cylinder, are you getting a brake light?

Sep 14, 2011 | 2004 GMC Sierra

2 Answers

My 1997 chevy 1500 z71 brakes suddenly going all the way to the floor. Checked brake fluid and it was low. Could be wheel cylinder? Master cylinder? or ?


well, check the brake lines for leakage after adding brake fluid to the full mark. If the brake pedal goes all the way to the floor, it's likely there is a leak somewhere after the master cylinder. If the pedal gets hard after adding fluid, and pumping it several times with the car off, then the master cylinder is still ok.

If air has gotten into the master cylinder, it may have to be bled out on a bench, or using a scanner if that's the way your vehicle is.

Bleeding the Brake System (ABS) Auto Bleed Procedure NOTE: Perform a manual bleeding procedure. If the brake pedal height and firmness results are not achieved, perform the auto bleed procedure below.
NOTE: Perform this procedure when replacing the brake pressure modulator valve or electro-hydraulic control unit.
  1. Perform the manual brake bleeding procedure. Refer to Bleeding the Brake System (non-ABS).
  2. Check the master cylinder fluid level often to prevent running the system dry.
  3. Press the brake pedal firmly and run the Scan Tool Automated Bleed Procedure (for Gas engines) once, or the Function Test (for Diesel engines) four times. Make sure to release the brake pedal between each test.
  4. Perform the manual bleed procedure again. This should remove the remaining air from the brake system.
  5. Bleed the system as many times as needed to obtain the appropriate feel of the brake pedal.

Dec 18, 2010 | 1997 Chevrolet K1500

1 Answer

II was changing my brake pads and accidently unscrewed the bolt to my break fluid. I finished the pads and went to set the brake and it just went to the floorboard and checked brake fluid. the resivoir was...


WHEN FINISH REPLACING BRAKE PADS.MAKE SURE MASTER CYLINDER COVER ON FLUID LEVEL OKAY.YOU PUMP BRAKE PEDAL UNTIL BRAKE PEDAL GET FIRM HARD.IF BRAKE PEDAL KEEP GOING TO THE FLOOR YOU HAVE AIR IN THE HYDRALIC BRAKE SYSTEM.BRAKE SYSTEM NEED BLEEDING.DONT DRIVE VECHICLE IF BRAKE PEDAL FEEL SPONGY OR GO TO FLOOR.

Oct 20, 2010 | 1999 Nissan Pathfinder

2 Answers

My clutch pedal is stuck to the floor??


It is most likely a hydraulic clutch, and it is most likely leaking at the clutch slave cylinder. Check the clutch master cylinder for fluid, it should be a small master cylinder looking thing with a fill cap next to the brake master cylinder and booster unit. If it is empty fill it with the same dot 3 brake fluid that you use for your brake master cylinder, and make sure that you are pouring the fluid into the clutch master cylinder reservoir and not the rubber seal that should be under the fill cap. After filling the clutch master cylinder up with fluid, then try and pump up the clutch pedal. It might take a while to pump up hydraulic pressure, and you might also have to work the pedal a few times by hand at first.

Also, you might have to bleed the clutch at the slave cylinder if it will not build up enough pressure to release the clutch.

Apr 28, 2010 | 1988 Mazda RX-7

1 Answer

How to replace the clutch? I have a hydraulic clutch and the petal went to the floor today, I assume the clutch went out


the first thing that i would check is the fluid level in the clutch master cylinder. It is just like the brake system. When there is not enough fluid or if there is air in the system this can cause the pedal to go to the floor. If this is ok then a portion of the clutch MIGHT have went out. Let me know if the hydraulics are ok.

Jun 10, 2009 | 1989 Jeep Wrangler

1 Answer

Brake pedal will go all the way to the floor


make sure brake fluid is full. then pump brakes for one minuite check the fluid to see if it went down or stayed full. if it went down then check the system for a leak . if it stays full then you will need a new mastercylender . i dont think you have a vacum problem cause this causes a verry stiff brake pedal not one that goes to the floor

Dec 26, 2008 | 1993 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...