Question about 2000 Pontiac Grand Prix

Open Question

2000 pontiac grand prix serpintine belt routing diagram with out ac

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
PyroPCMan
  • 405 Answers

SOURCE: diagram on a pontiac grand prix

Ignition Switch GM Century/Lumina/Grand Prix/Intrigue 1997-2000 The vehicles covered by this guide use one of two types of ignition switches:

  • A mechanical key and lock cylinder built into the steering column, that works a pull rod to actuate the separate electrical portion of the ignition switch mounted further down the steering column. For more information and replacement procedures on this type of switch, please see .
  • An instrument panel-mounted ignition switch is also used on some W-Body vehicles. To service this switch, the radio, heater & A/C control panel and the instrument cluster must be removed. All of these procedures are found elsewhere in this section.
REMOVAL & INSTALLATION
Instrument Panel-Mounted Ignition Switch
WARNING You must perform the Body Control Module (BCM) theft deterrent relearn procedure after replacement of the ignition lock cylinder. Failure to perform this relearn procedure means the BCM will not function properly. This means the vehicle will not be theft protected by the Passlock system and the engine may not crank or start. GM recommends that this procedure be performed with their Tech 2® or equivalent scan tool. An alternate relearn procedure is given at the end of this procedure.
  1. Disconnect the negative battery cable.
  2. Remove the radio assembly following the procedures found in this section.
  3. Remove the heater & A/C control head assembly following the procedures found in this section.
  4. Remove the instrument cluster assembly following the procedures found in this section.
  5. Detach the electrical connectors from the ignition switch.
  6. Insert the key and turn the ignition switch lock cylinder to the ACC position.
  7. Depress the transaxle park/lock cable retainer to release, then pull to remove the cable from the ignition switch.
NOTE You must perform the Body Control Module theft deterrent relearn procedure after replacement of the ignition lock cylinder.
  1. If it is necessary to remove the ignition lock cylinder from the ignition switch (theft damage, etc.), use the following procedure:
    1. Insert the key and turn the ignition switch lock cylinder to the ON position.
    2. Using a small flat-bladed tool, depress and hold the lock cylinder retaining tab.
    3. Using the key as an aid, pull to remove the ignition switch lock cylinder from the switch.
    4. Remove the key from the lock cylinder.
    5. Carefully pull to release the ignition switch bezel from the ignition switch lock cylinder.
  2. Remove the ignition switch bracket bolts and remove the ignition switch through the instrument panel cluster opening.
  3. Remove the bolts retaining the ignition switch to the bracket and remove the bracket.
0900c15280090fea.jpgRemoving an instrument panel-mounted ignition switch assembly—1998 Oldsmobile Intrigue shown, others similar To install:
  1. Install the ignition switch to its bracket and install the bolts. Install the ignition switch into position through the instrument panel cluster opening and install the bracket retaining bolts.
  2. If removed, install the ignition switch lock cylinder to the ignition switch using the following procedure:
    1. Recode the lock cylinder, if necessary.
    2. Align the ignition switch bezel to the tabs on the ignition switch lock cylinder and carefully press to secure in place.
    3. Insert the key and turn the ignition switch lock cylinder to the ON position.
    4. Align the ignition switch lock cylinder to the ignition switch, then press into place.
  3. Turn the key to the ACC position. Align and press into place the transaxle park/lock cable to the ignition switch. Remove the key from the switch.
  4. Attach the electrical connectors to the ignition switch.
  5. Install the instrument cluster using the procedures found in this section.
  6. Install the heater & A/C control panel using the procedures found in this section.
  7. Install the radio assembly using the procedures found in this section.
  8. Connect the negative battery cable.
  9. If the lock cylinder was removed, perform the BCM Programming/RPO Configuration procedure.
THEFT DETERENT RE-LEARN—WITHOUT TECH 1®SCAN TOOL
This procedure takes approximately 30 minutes. Make sure the battery is fully charged before proceeding.
  1. Turn the ignition switch to the OFF position.
  2. Turn the ignition switch all the way from the OFF to the START position, then leave it in the ON position. The engine will not crank.
  3. The SECURITY light should come on and stay on for at lease ten minutes.
  4. Turn the ignition switch to the OFF position for five seconds.
  5. Repeat Steps 2, 3 and 4 again for a second time.
  6. Repeat Steps 2, 3 and 4 again for a third time.
  7. Turn the ignition switch to the OFF position.
  8. Turn the ignition switch all the way to the START position. The engine should now start.

Posted on Sep 09, 2008

Ad
Brian032472
  • 150 Answers

SOURCE: 2004 kia serpintine belt routing diagram

Notes 98650681

Posted on Nov 03, 2008

bunnydawg
  • 5158 Answers

SOURCE: 2004 pontiac grand prix serpentine belt replacement/ routing

first look underneath the hood... is it there on a sticker... if not i'll need the size of the motor to let you know

Robert

Posted on Jan 27, 2009

c17hydro
  • 2984 Answers

SOURCE: I need a diagram of the routing of a serpentine

Here ya go:


07ea531.gif

Posted on Aug 30, 2009

tbirdfan1
  • 3051 Answers

SOURCE: need a serpintine belt routing diagram for a 2000 pontiac Montana

Hello there: here it is
2f0d8b6.jpg

Posted on Jan 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to put supertine belt on 2004 grand prix


Under the hood there will be a routing diagram for the serpentine belt. Use that as a guide for replacement routing. There is an automatic belt tensioner in the loop. Use an appropriate tool to release the tension on the old belt and remove it from the vehicle. Route the new belt as per the diagram and allow the automatic tensioner to re-tension the belt.

Jan 11, 2015 | 2004 Pontiac Grand Prix

2 Answers

I think i routed my serpentine belt wrong i need a really clear routing diagram for a 2004 grand prix


usually somewhere under the hood you will find a diagram showing how your belt should go. If not ask your local discount auto parts store and they can help you.

Aug 17, 2012 | 2004 Pontiac Grand Prix

1 Answer

Tensioner belt was replaced on 1992 grand prix but still wont start. troubleshooting needed.


Re check the belt routing.

Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Feb 07, 2012 | 1992 Pontiac Grand Prix

1 Answer

I need a diagram for changing a serpentine belt on a 2006 grand prix of some kind of information to help me with the putting the belt back on


2006 PONTIAC GRAND PRIX - V6 3.8L
Belt Routing Diagram - Multiple Accessory (Main Drive)

cff7db4.jpg

Hope helps (remember rated this) Good luck.

Jan 15, 2010 | 2006 Pontiac Grand Prix

1 Answer

Serpintine belt replacement


OK, click on the link below to be directed to a full size photo of your belt routing diagram.

2000 Grand caravan Serpentine Belt Routing

Please rate and have a great day:)

May 18, 2009 | 2000 Dodge Grand Caravan

1 Answer

Serpentine belt diagram for


Usually and on most cars there's a belt diagram on the inside of the engine compartment near the radiator housing

Apr 04, 2009 | 1994 Pontiac Grand Prix

2 Answers

Serpintine belt


This link will take you to a picture of the diagram. If the link doesn't work contact me and I can email you the picture directly.

http://autorepair.about.com/library/illustrations/bl506a-lib.htm

Jan 10, 2009 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Pontiac Grand Prix Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...