Question about 2000 Ford Explorer

1 Answer


Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 71 Answers

When the overdrive lamp flashes it's a warning that the transmission has a concern that is either internal or external (wiring, computer). A scan will need to be performed to determine which part of the transmission is at fault. Many auto parts stores will perform a free scan however many cheaper testers will not pick up transmission codes. The overdrive servo in the Explorer trans has often caused problems with the return spring breaking. This is a repair that can be made without removing the trans. Another concern could be a shift solenoid not operating properly. The trans pan would have to be removed to address a solenoid issue. Internal gears/clutches are also a possibility. Repairs for this concern could run from a few hundred to a few thousand dollars. Diagnosis would run from $0 - $150.00. Good luck.

Posted on Apr 06, 2011

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the iat sensor on a 2000 Ford Explorer -5.0

Inside the MAF Sensor

In ducting from Air Filter

Dec 16, 2012 | 2000 Ford Explorer

2 Answers

How do check the CPS on a 2000 Ford Explorer?

you cannot check crankshaft postion sensor if your car has hard starts or does not start your crankshaft postion sensor is faulty it tells cars pc when to fire spark and to what cylinder to fire it to

if it helps please leave a 4 thumbs review if it helps

May 10, 2011 | 2000 Ford Explorer

2 Answers

I have a 2000 ford explorer 4.0 v6 ohv and i have an bank 1 sensor 1 code. which o2 sensor is that?

Ford Explorer and V8 O2 Sensor Locations diagram. This shows the location of Ford oxygen sensors on Bank 1 and Bank 2. If you want to know where your O2 sensors are, this diagram is your guide (click over pic for zoom)...


Hope helps with this (remember to rate and comment this answer).

Apr 29, 2011 | 2000 Ford Explorer

1 Answer

2000 Ford explorer check engine light on code came up as P1309.What can be done to fix?

This indicates a camshaft position sensor fault, could be the sensor, wiring or the computer, needs to be properly diagnosed.

Jul 28, 2009 | 2000 Ford Explorer

1 Answer

Oil sensor

please rate as problem solved if this is what you need.

Disconnect the oil pressure sensor electrical connector.


Jun 01, 2009 | 2000 Ford Explorer

1 Answer

4wd indicator lights flashing.

this sounds like you need both speed sensors and shift motor for your transfer case.

Mar 04, 2009 | 2000 Ford Explorer

1 Answer

High idol when cranked

the idle controll sensor is on the intake manifold replace it and reset codes

Jan 09, 2009 | 2000 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

499 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers


Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides