Question about 2001 Ford F150 Styleside SuperCrew

1 Answer

I did the self test on my 2001 ford f-150 cruise control and only got the flash after pushing the off button. I did not get a flash after pushing the on button. What does this mean?

Posted by on

  • mmeadows49 Apr 05, 2011

    Yes and got nothing

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 984 Answers

This is usually an indication of an issue with the switch.

Did you try a few times, and try pushing on different areas of the button, to see if the pivot for the switch is the issue ?

Posted on Apr 05, 2011

Testimonial: "Thank You"

  • Steve S
    Steve S Apr 12, 2011

    The 2 places I would look next,
    1. The cruise control servo motor connector, to make sure it has no sign of burnt damage to it.

    2. The switch itself ( requires removing the airbags )

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 f150 cruise inop shows code 3?


  • 3 flashes - deactivator switch is open or circuit defective.
    • Flash code 3 - deactivator switch circuit failure
    • Central junction box (CJB) fuse 13 (20A).
    • Circuitry.
    • Deactivator switch.
    • Speed control servo.
    • Go To Pinpoint Test H .
    PINPOINT TEST H: FLASH CODE 3 - DEACTIVATOR SWITCH CIRCUIT FAILURE
  • CONDITIONS DETAILS/RESULTS/ACTIONS H1 CHECK THE DEACTIVATOR SWITCH CIRCUITRY
    Speed Control Servo C122
    Measure the voltage between the speed control servo C122 pin 9, circuit 307 (BK/YE), harness side and the speed control servo C122 pin 10, circuit 57 (BK), harness side.
    • Is the voltage greater than 10 volts?
    Yes INSTALL a new speed control servo. REFER to Speed Control Servo in this section. REPEAT the self-test.

    No GO to H2 . H2 CHECK DEACTIVATOR SWITCH POWER
    Deactivator Switch C1025
    Measure the voltage between the deactivator switch C1025, circuit 10 (LG/RD), harness side and ground.
    • Is the voltage greater than 10 volts?
    Yes GO to H3 .

    No REPAIR the circuit. REPEAT the self-test. H3 CHECK CIRCUIT 307 (BK/YE) FOR AN OPEN Measure the resistance between the speed control servo C122 pin 9, circuit 307 (BK/YE), harness side and the deactivator switch C1025, circuit 307 (BK/YE), harness side.
    • Is the resistance less than 5 ohms?
    Yes INSTALL a new deactivator switch. REFER to Speed Control Deactivator Switch in this section. REPEAT the self-test.

    No REPAIR the circuit. REPEAT the self-test.

Nov 23, 2016 | 2002 Ford F-150

1 Answer

Which fuse is for cruise control in 2003 ford f150


The fuses for the speed control from the factory are :
Engine Compartment fuse panel #7,
Cab fuse panel Fuses #15, #13, #5

The fuse that goes to the recall part is Fuse #13, 20A

The recall is 05S28. Description: Speed Control Deactivation Switch.
The part number for the recall is : 1L1Z-9F924-AA
The part has a fuse inline that is marked as non serviceable, but 1 revision I saw, it was just an ATM fuse under tape. Not sure if this is the final revision that was used on your truck ( or should have been used ).


The self test for the Cruise Control ( for 00-03 MY, with the CC light on the cluster ) :

With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 19, 2010 | 2003 Ford F150 Regular Cab

1 Answer

Cruise control no working on 2001 f-150 4 x 4 5.4


Did you have the recall done ?
recall 05S28. Description: Speed Control Deactivation Switch.

Try the self test for the Cruise Control :


With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

- 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

- 3 flashes - deactivator switch is open or circuit defective.

- 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 15, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

Cruse control not working does it have afuse


It should have a fuse! check manual in glove box. Also , Brake light out in most newer vehichles keeps cruise from working

Jun 14, 2010 | 2001 Ford F150 Styleside SuperCrew

1 Answer

2001 F-150 cruise control stopped working. Already checked the fuse and it's good. What's next


really tough to do on the net but first we need to know about any codes...

Hold speed control OFF button, and turn ignition switch to RUN position. CRUISE indicator should flash once to indicate successful entry into self-diagnostic mode. If CRUISE indicator does not flash, start procedure over. If CRUISE indicator still does not flash, repair system by symptom there might be some switch concern

If CRUISE CONTROL indicator flashes once followed by 5 additional flashes, replace speed control servo/actuator.

Release speed control OFF button. Within 5 seconds in entering self-diagnostics, press speed control ON button. Press remaining speed control buttons in the following sequence; ON, RES, COAST and SET/ACCEL.

As each button is pressed, CRUISE indicator will flash.

Wait until indicator light goes out, then press next button. After sequence has been completed, indicator light will flash to indicate test passed or failed. With the codes we can then better diagnose your concern

Immediately after static test has passed, actuator performs a dynamic test by automatically operating throttle .04-.40" (1-10 mm). Observe throttle movement to witness any sticking in cable or linkage. Ensure throttle returns properly. Turn ignition switch to LOCK position. If self-diagnostics do not pinpoint fault there is more we can do but tough over the net

Mar 26, 2010 | 2001 Ford F150 Styleside SuperCrew

2 Answers

2002 Ford F150. Cruise control stopped working.


Did you have the recall done on it ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be a blow fuse in the recall harness, if you did have it done.

Try the self test, and see what the results are. If you do not get it into self test mode, it could be the fuse in teh recall harness that is blown. The 1st revision of the recall harness was an inline ATM fuse, not sure if the revision 2 was the same. If that fuse is blown, the switch is leaking, and should be checked.

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

Feb 22, 2010 | 2002 Ford F150 Regular Cab

1 Answer

Cruise control will not turn on. light on dash use to come on. cruise will not work. checked fuse it is ok


Did you have the recall for the cruise control done ?
recall 05S28. Description: Speed Control Deactivation Switch.

It could be the fuse in the recall harness is blown.

Try the Cruise Control Self test :
----------------------------------
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.
----------------------------

If the Cruise Control does not enter self test, the fuse in the recall harness ( if done ) is most likely blown and needs to be replaced.

Feb 02, 2010 | 2002 Ford F150 Regular Cab

1 Answer

I have a 2001 ranger 4.0 automatic w/od and 40k cruise control


Ford has a recall on yours if a tilt wheel is an option in your truck

Jan 16, 2010 | 2001 Ford Ranger Regular Cab

3 Answers

Cruise does not work on Ford F150


Once you verify / change the Cruise Control Switch
This is the recall that hickoryy472 posted about ( you can also check on the ford site to see if it is still outstanding, it is free ).
recall 05S28. Description: Speed Control Deactivation Switch.

Another option for testing is to pull the connector on the End of the Master Cylinder, and jumper the 2 pins in the connector together. This is a secondary safety switch, in case the tail lamps go out while using the CC, that the pressure switch will shut off the CC.

Next you can run a self test on the CC :

There is a self test in the cruise control system.
With the key off depress and hold the cruise control off button while turning the ignition to the run position,don't start the truck, the cruise light will flash once to let you know it is in self test.
Five additional flashes indicate a bad cruise control servo

Release the cruise off switch and within 5 seconds depress the other switches in sequence:
1. on
2. resume
3. coast
4. set/ accel
The speed control light will flash as each switch is depressed.

If the last one does not flash it may then flash a code

After this the cruise will move the throttle to test the actuator and the cable.
Make sure the throttle returns to idle and turn the key off.
----------------------

Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

You don't have the stalk GM type CC switch, so clint969's post is good info, just for another manufacture.
The buttons ( if they are the problem ) can be removed from the steering wheel without pulling the steering wheel itself on a Ford.

Start with the recall, and then test the CC, and see if you have an issue still

Nov 28, 2009 | 1998 Ford F150 Regular Cab

1 Answer

2001 F150 6 cyl. Cruise control just quit working today. I turn it on and hit set, cruise light flashes and does not stay on. Please Help. M Mitchell


2 things

1. Is your truck in the list for the recall, or did you have it done ?
recall 05S28. Description: Speed Control Deactivation Switch.

2. Run the Cruise Control Self test
Self-Test Diagnostics

WARNING:
This test is a key on engine off (KOEO) test only that is conducted in park only with emergency brake fully engaged.

1. Enter self-test diagnostics by depressing the speed control OFF switch while turning the ignition key ON, making sure the engine does not start and is not running. The speed control indicator on the instrument panel will flash once to indicate that speed control module entered the diagnostic mode. Five additional flashes at this point indicate a defective speed control servo. Release the OFF switch.

2. Press the remaining switches in this sequence: ON, RESUME, COAST and SET/ACCEL.

If the ON switch is not depressed within five seconds after entering the diagnostics mode, the module times out and the procedure must be started over.

The speed control indicator lamp will flash as each switch is depressed. Press each switch in the sequence immediately after the indicator light goes out for the previous switch.

Note:
There will be a slight delay when the last button is pressed and the lamp flashes.

3. A lamp flash with the last button (SET/ACCEL) indicates that the static test passed. If the lamp does not flash with the last button and there are no additional flashes of the lamp, the switch is defective.

If the lamp does not flash with the last button, and additional flashes occur, follow the chart below for trouble codes:

— 2 flashes - BPP defective, circuit is defective, brake applied, CPP switch or jumper (if equipped).

— 3 flashes - deactivator switch is open or circuit defective.

— 4 flashes - vehicle speed signal is out of range or circuit is defective

4. Immediately (.25 second delay) after the static test, the speed control servo does a dynamic test by automatically actuating the throttle lever from 8 mm (0.315 in) to 12 mm (0.472 in) of travel from the idle position. During the dynamic throttle pull, observe throttle movement to witness any binding or sticking of the speed control cable and correct connection of speed control cable to throttle lever. Make sure the throttle returns to the idle position.

5. Return the ignition switch to the OFF position and proceed to the Symptom Chart.

Oct 22, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
2001 Ford F150 Styleside SuperCrew Logo

185 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...