Question about Ford Fusion

Open Question

Timing marks for chain on 2005 ford fusion 2.3 engine

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: 3.3l dodge caravan, where to set timing chain marks

the top gear timing mark points at 6oclock...crank gear at 12 oclock

Posted on Sep 27, 2008

Ad
  • 366 Answers

SOURCE: does 2005 ford expedition have a timing belt or chain?

v8s have timing chains

Posted on Feb 24, 2009

  • 1348 Answers

SOURCE: 2001 Ford Explorer 4.0 SOHC no timing marks on cam or chain

get a haynes manual and look up camshaft replacement..its worth the 30 bucks

Posted on May 14, 2009

  • 1596 Answers

SOURCE: Need timing marks for 2002 ford explorer 4.0




The Info I Have Is Extensive and Has Illistrations, I Need to Emali it to You As it is Very Large, This Is A Small Example Im @rejakwilson@aol.com

Special Tool(s)

  1. With the vehicle in neutral, position it on a hoist.
  2. Remove the intake manifold.
  3. Remove the fuel supply manifold.
  4. Remove the accessory drive belt.
  5. Remove the thermostat housing.
  6. Remove the roller followers.
  7. NOTE: You must retime the LH and RH camshafts when either camshaft is disturbed. Turn the crankshaft clockwise to position the number one cylinder at top dead center (TDC).
  8. NOTE: Late build pulley shown, early build pulley similar. NOTE: The special tool must be installed on the damper and should contact the engine block to position the engine at TDC.

Posted on Jul 24, 2009

c17hydro
  • 2984 Answers

SOURCE: where are timing chain marks on the engine of

Please don't forget to rate:

39900a5.gif

Crankshaft and camshaft alignment marks—2.4L (VIN X) Engine

9f5c6e9.gif
Camshaft and crankshaft alignment marks—Chrysler 2.5L (VIN N) engine

acb6bd1.gif
Timing belt engine sprocket timing—2.5L (VIN H) engine

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the cost to replace timing chain in 2002 ford explorer


replacing timing chain???...Costs??? - Ford Explorer

www.explorerforum.com > ... > Stock 2002 - 2005 Explorers

Mar 20, 2008 - 8 posts - ‎5 authors
Stock 2002 - 2005 Explorers. ... What is the reccommneded time to replace the timing chain in a '02 Explorer 4.0 ... Costs inc. mechanics labor? Timing chain replacement cost on 2003 Ford Explorer ...
2 posts
Dec 2, 2011
Timing chain rattle resolution process - SOHC V6
19 posts
Jul 6, 2011
Timing Chain Replacement Cost - Ford Explorer and ...
6 posts
Jul 28, 2010
4.6L Explorer engine timing chain ooops! - Ford ...
19 posts
Jan 10, 2008
More results from www.explorerforum.com

Estimate of cost for a timing chain replacement - 2003 Ford ...


Dec 15, 2015 | 2002 Ford Explorer

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

How to set a timing in a 2005 ford focus


Timing chain or belt? Almost all timing gears have a dot that face each other when the timing marks are lined up. If you are not carful you can damage the valves while rotating the crank and came to the lined up position. However in a perfect world the top gear can be removed when it is lined up, and reinstalled with the chain or belt in place, it will be tight but you should not need to force it. good luck

Jul 27, 2014 | 2005 Ford Focus 2.0

1 Answer

When do I change the timing belt on a 2004 Ford Fusion?


believe the Fusion has a timing chain and not a belt. but the owner's manual under maintenance can tell you when either service is required.

Jun 06, 2012 | 2008 Ford Fusion

1 Answer

Need tiing diagram for 2005 5.4l engine


If your talking about the cam timing, then it's a bit complicated. There are two timing chains and the marks depend on having chains with different colored links to line them all up.

The crankshaft should be where the key way is at about the 270 degree mark and the crank gear with the timing mark is at the bottom. the D/S chain goes on first and there should be a machined notch that will be "up". the raised line will be down. The chain goes on with the SINGLE colored link at the crank mark and the notch between the TWO links. The P/S chain goes the same way but the cam gear only has the one notch on it. Here is a picture:

chuckster57_39.gif

Apr 27, 2011 | Ford Expedition Cars & Trucks

2 Answers

Looking for timing marks for Ford f150,1991.


zjlimited_22.jpg

Fig. 2: Installation of the gasoline V8 engine timing chain installation


zjlimited_23.jpg

Fig. 3: Align the timing marks on the timing chain sprockets-5.0L, 5.8L and 7.5L engines

Hope helps (remember to rate and comment this).

Nov 04, 2010 | 1991 Ford F150

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

1 Answer

Need timing marks for 2002 ford explorer 4.0 engine. trying 2 check timing chain. any one know specs


There are no marks on this one. There is a special tool set to align camshafts ($900). The best you can do is to bring #1 cyl to TDC compression with both cam(valve) covers off. #5 cyl should have lobes at equal opening, exhaust just closing and intake just opening.. #1 cyl cam lobes should each be diametrically opposed to the positions of #5. If cams need to be moved, there is no registration of gear onto cam. Just loosen bolt holding gear and move cam. Retighten bolt. Roll thru 2 crank revolutions and check cam timing again.Simple.

Jul 24, 2009 | 2005 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5613 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...