Question about Audi A4

Open Question

Where are the timing marks located on the camshafts of an audi a4 1998

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 883 Answers

SOURCE: camshaft timing mark

here's a graphic:
df5d4d2.jpg
please rate me solved!
Thanks!

Posted on Jun 26, 2008

TLRogue
  • 99 Answers

SOURCE: temperature sensor audi a4

Possibly located at the back of the engine behind cylinder head, usually located in a small plastic hose block.

TL

Posted on Jan 23, 2009

  • 102 Answers

SOURCE: engine number location for 2002 audi a4

is it a 1.8 turbo or 2.8 V6 or 2.7 biturbo V6 ? on most models what you will be looking for is a 3 letter code like ATQ or APW and is normally on a sticker on the timing belt cover, it is also stamped into the engine on a ledge up high. if no luck there check the owners manual, around the 3rd page there will be a sticker that was put in the book during predelivery inspection this sticker is about 3 inches by 3 inches and filled with id codes for almost everything. If the pdi wasn't done right another copy of the same sticker will be under or next to the spare tire in the spare tire well.

Posted on Mar 24, 2009

  • 1 Answer

SOURCE: audi a4 2.8 30v 1998 ack engine

It is mounted to the transmission bellhousing on the driver's side. The connector is mounted on the firewall and is a smaller, gray connector. You can reach the sensor from underneath.

Posted on Apr 01, 2009

  • 5 Answers

SOURCE: Replacing Camshaft Position Sensor Guide audi a4

The camshaft position sensor is located behind timing belt cover in front of engine.Remove cover, sensor is visable in top right hand corner.Unplug, remove 2 10mm bolts.Reinstall,plug back up,reinstall cover,crank engine.

Posted on Sep 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Camshaft shaft timing marks on a 2000 audi s4


you can make your own marks by using a tip ex or white marker .

is it a petrol

if yes then take the coil pack of the cylinder one and turn the engine till the spark plugs reaches to the very top. that's your engine timing mark..

Mar 04, 2016 | Audi Cars & Trucks

1 Answer

Timing marks for 1994 audi 2.8 v-6


the "timing marks" on audi"s are on the cam sprockets. large holes on the lobes of the camshaft gears are supposed to face each other when cylinder 3 is at TDC the crankshaft has an arrow that needs to be aligned as well. see pics for reference
c5afa606-e7a0-4acf-aaa5-3184a05fa4a1.jpg

Dec 28, 2013 | 1993 Audi 90

1 Answer

I have audi A8 2005 model V6 engine 3.0L need timing mark location


the timing marks are located on the pulleys , clean them off & then run around the pulleys with pool cue chalk, the timing marks are plainly visible after this little trick/tip.

Sep 13, 2012 | 2005 Audi A8

1 Answer

Need 2000 Audi A8 4.2 engine timing belt marks


dak408_36.gif
dak408_37.gif
dak408_38.gif
There are no alignment marks on the camshafts, you must use the camshaft holder tool T40005 in conjunction with the crankshaft holder tool 3242 to properly align the camshaft and crankshaft

CAUTION: Incorrect removal or installation of the timing belt can result in damage to internal engine components.

Nov 19, 2010 | 2000 Audi A8

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

1 Answer

Have a 2.5tdi pd touareg. need timing marks?


the timing marks for all vw/audi/seat and skoda are on the front pulleys(they are small dots)you may need to highlight them with chalk.

May 10, 2010 | 2004 Volkswagen Touareg

1 Answer

Got audi a4 1996 diesel need to change cambelt but


A diesel uses a different procedure. You'll need a tool to hold the camshaft pulley parallel to the top of the cylinder head. The timing mark to set TDC for piston #1 is located on top of bell housing. The pointer must be aligned on the diamond cut on the flywheel. A VW/Audi setting bar tool #2065A is needed to lock the camshaft in position. Lock the injection pumpin position using the special lock pin (VW/Audi special tool no. 2064). Caution: If the drive belt is broken or has jumped time, do not attempt to lock the sprocket at this time!!! You will also need VW/Audi special tool no. VW210 to measure belt tension between camshaft sproket and injection pump sprocket. So good luck.

May 01, 2010 | 1996 Audi A4

2 Answers

What's the correct way of installing the camshafts on an Audi 1.8T B6 motor?


align timing marks on furthermost bearing caps on exhaust and inlet side to respective camshaft sprockets. to confirm correct fitment, their should be 16 chain links starting from one timing mark to the other.

Apr 20, 2010 | 2002 Audi A4

1 Answer

Replacing Camshaft Position Sensor Guide audi a4


The camshaft position sensor is located behind timing belt cover in front of engine.Remove cover, sensor is visable in top right hand corner.Unplug, remove 2 10mm bolts.Reinstall,plug back up,reinstall cover,crank engine.

Sep 11, 2009 | 2002 Audi A4

1 Answer

How do i set the timing for audi A6 2003


there are actually special tools the cam has no timing marks the tool only goes on one way and locks the cams in place and it is actually a long process but there is no way to do it without the cam lock

Aug 20, 2009 | 2003 Audi A6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14337 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...