Question about 2005 Volvo S60

1 Answer

There is no indicators working on the car the message trip computer system is stuck on the same message and and cannot toggle between average speed etc. the message and dashboard lights are very dull. the headlight main beam does not work as does the fog lights. however the hazard warning lights flash but only when the ignition is on.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 54 Answers

The hazards most likely still work, but when they key is out, it won't flash on the dash, but will outside.

As for the indicators and trip...could be either a steering wheel module to a turn signal stalk issue.

Were you having problems with the turn idicators acting weird before?

Posted on Aug 15, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My mph, gas, and temp gauges are not working


That's why you don't let you husband work on your car ! Unless he does it for a living .. For MPH there is a VSS - vehicle speed sensor , for the gas there is a sending unit in the fuel tank, for the temp. gauge there is a temp. sensor located in coolant stream on the engine .You more then likely need to have you instrument cluster repaired . GM had a problem with step motors inside the instrument cluster . A step motor is what controls the individual gauge. The sensors are all inputs to the PCM - powertrain control module (engine computer ) .
Engine Coolant Temperature Gage
The IPC displays the engine coolant temperature as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine coolant temperature. The engine coolant temperature gage defaults to C or below if:
?€¢
The PCM detects a malfunction in the engine coolant temperature sensor circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

Fuel Gage
The IPC displays the fuel level as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the fuel level percent. The fuel gage defaults to empty if:
?€¢
The PCM detects a malfunction in the fuel level sensor circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

When the fuel level is less than 14% (84ohms), the low fuel indicator illuminates.
Odometer
The IPC contains a season odometer and a trip odometer. Momentarily press the trip select/reset switch in order to toggle between the season odometer and the trip odometer. Press the trip select/reset switch for greater than 1.5 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The IPC displays the vehicle mileage and trip mileage as determined by the IPC. The IPC calculates the mileage based on the vehicle speed information from the PCM. The odometer will display 'error' if an internal IPC memory failure is detected.
PRNDL Display
The IPC displays the selected gear position as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the gear position. The PRNDL display shall flash all gear positions if:
?€¢
The PCM detects a malfunction in the transmission range switch circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

Speedometer
The IPC displays the vehicle speed based on the information from the PCM. The PCM converts the data from the vehicle speed sensor to a 4000 pulses per mile signal. The IPC uses the vehicle speed signal circuit from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 mph (0 kph) if a malfunction in the vehicle speed sensor circuit exists.
Tachometer
The IPC displays the engine speed as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine speed. The tachometer will default to 0 rpm if:
?€¢
The PCM detects a malfunction in the engine speed sensor circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

May 22, 2016 | 2002 Buick Century

1 Answer

I have a 2010 Chevy impala LS instrument cluster and it has a 20 pin plug I'm trying to figure out which wire's on the back of the cluster are for the speed sensor, rpm, gas, and temp wires.


Boy your way off base . All the gauges are inputs from the ECM - engine computer . The VSS - vehicle speed sensor , ETC - engine coolant temp sensor , sending unit in the fuel tank , All this sensors input the engine computer . The PCM then sends this info on the GMLAN serial data bus ,communications network . The Instrument cluster has a microprocessor inside that translates this info an controls the gauges. You probably have an instrument cluster problem or a communication network problem . Your best bet is to take your vehicle to the dealer or some other qualified repair shop. Need to have it checked for DTC'S - diagnostic trouble codes.
Indicators and Warning Messages
Refer to Indicator/Warning Message Description and Operation.
Engine Coolant Temperature Gage
The instrument panel cluster (IPC) displays the engine coolant temperature as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the engine coolant temperature. The IPC receives the coolant temperature information via serial data message from the body control module (BCM). The engine coolant temperature gage defaults to 60?°C (140?°F) or below if:
?€¢
The ECM detects a malfunction in the engine coolant temperature sensor circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the BCM.
Fuel Gage
The instrument panel cluster (IPC) displays the fuel level as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the fuel level percent. The body control module (BCM) sends the fuel level information from the ECM to the IPC via a serial data message indicating the fuel level percent. The fuel gage defaults to empty if:
?€¢
The ECM detects a malfunction in the fuel level sensor circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the BCM.
When the fuel level is less than a pre-determined value, the low fuel indicator illuminates in the IPC.
Odometer
The vehicle odometer is calculated and stored electronically in the instrument panel cluster (IPC). The IPC contains a season odometer and trip odometer A or B. Momentarily press the trip/fuel button in order to toggle between the season odometer and the trip odometer. Press the set/reset button for greater than 0.25 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The IPC displays the vehicle mileage and trip mileage as determined by the engine control module (ECM). The IPC calculates the mileage based on the serial data vehicle speed information from the ECM. The odometer will display 'error' if an internal IPC memory failure is detected. The odometer displays either miles or kilometers and can be set through the customization menu in the driver information center (DIC).
PRNDL Display
The instrument panel cluster (IPC) displays the selected gear position as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the gear position. The PRNDL display blanks if:
?€¢
The ECM detects a malfunction in the transmission range switch circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the body control module (BCM).
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed as determined by the engine control module (ECM). The IPC calculates the mileage based on serial data vehicle speed information from the ECM. The IPC receives vehicle speed information from the body control module (BCM) via a serial data message. The speedometer defaults to 0 km/h (0 mph) if the IPC detects a loss of serial data communications with the ECM or BCM.
Tachometer
The instrument panel cluster (IPC) displays the engine speed as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the engine speed. The IPC receives the engine speed information from the body control module (BCM) via a serial data message. The tachometer will default to 0 RPM if:
?€¢
The ECM detects a malfunction in the engine speed sensor circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the BCM.

How to Diagnose Controller Area Network CAN Suggest you read up on C.A.N.

May 14, 2016 | Cars & Trucks

1 Answer

While driving antitheft light comes on and all the gauges go flat,car keeps runnig,want to disable system,not sure what to look for


Before doing something drastic ,have it checked out for DTC'S - diagnostic trouble codes . It may not be the anti-theft system ,gauges going flat would be more like a communication problem between modules . PCM / BCM / instrument cluster etc.. That also could cause theft light coming on . If your not sure what to look for ,take it to a ASE certified professional . You may render your vehicle useless if you don't know what your doing .
Serial Data Power Mode Master
On vehicles that have several control modules connected by serial data circuits, one module is the power mode master (PMM). On this vehicle, the PMM is the body control module (BCM). The PMM receives 3 discrete ignition switch signals to differentiate which power mode will be sent over the Serial Data circuits. The 3-wire Ignition Switch table below illustrates the state of these inputs in correspondence to the ignition switch position:
Serial Data Messages The modules that depend exclusively on serial data messages for power modes. stay in the state dictated by the last valid PMM message until they can check for the engine run flag status on the serial data circuits. If the PMM fails, the modules monitor the serial data circuit for the engine run flag serial data. If the engine run flag serial data is True, indicating that the engine is running, the modules fail-safe to RUN. In this state, the modules and their subsystems can support all operator requirements. If the engine run flag serial data is False, indicating that the engine is not running, the modules fail-safe to OFF-AWAKE. In this state, the modules are constantly checking for a change status message on the serial data circuits and can respond to both local inputs and serial data inputs from other modules on the vehicle.
Indicators and Warning Messages
Refer to Indicator/Warning Message Description and Operation .
Engine Coolant Temperature Gage
The instrument panel cluster (IPC) displays the engine coolant temperature as determined by the powertrain control module (PCM) or the engine control module (ECM). The IPC receives a serial data message from the PCM/ECM indicating the engine coolant temperature. The engine coolant temperature gage defaults to 38?°C (100?°F) if:
?€¢
The PCM/ECM detects a malfunction in the engine coolant temperature sensor circuit.


?€¢
The IPC detects a loss of serial data communications from the BCM.

Fuel Gage
The instrument panel cluster (IPC) displays the fuel level as determined by the powertrain control module (PCM) or the engine control module (ECM). The IPC receives a serial data message from the body control module (BCM) indicating the fuel level. The fuel gage defaults to E (empty) if:
?€¢
The PCM/ECM detects a malfunction in the fuel level sensor circuit.


?€¢
The IPC detects a loss of serial data communications from the BCM.

When the fuel level is less than 14 percent, the low fuel indicator illuminates.
Odometer
The instrument panel cluster (IPC) contains a season odometer and a trip odometer. Momentarily press the trip/reset switch in order to toggle between the season odometer and the trip odometer. Press the trip/reset switch for greater than 2 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The odometer is calculated and stored electronically in the body control module (BCM). The BCM uses the vehicle speed information from the powertrain control module (PCM) to calculate the odometer. The odometer displays 'error' if an internal IPC memory failure is detected. The IPC stores a backup copy of the odometer value incase the IPC stops receiving a valid odometer value from the BCM.
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed based on the information from the ECM/PCM. The IPC receives the vehicle speed information from the BCM via the serial data circuit. The speedometer defaults to 0 kmh (0 mph) when the following occurs:
?€¢
The powertrain control module (PCM) or the engine control module (ECM) detects a malfunction in the vehicle speed sensor circuit.


?€¢
The IPC detects a loss of serial data communication from the BCM.

Tachometer
The instrument panel cluster (IPC) displays the engine speed as determined by the powertrain control module (PCM) or the engine control module (ECM). The IPC receives a serial data message from the body control module (BCM) indicating the engine speed. The tachometer will default to 0 RPM if:
?€¢
The PCM/ECM detects a malfunction in the engine speed sensor circuit.


?€¢
The IPC detects a loss of serial data communication from the BCM.

Apr 07, 2016 | 2006 Pontiac G6

1 Answer

How to reset trip meter to zero for every journey on jaguar s type and also where the button to reset is please?


The two buttons that control the trip options are on the dash adjacent to the hazard warning button. Press the TRIP button untill it shows a small A or B in the top left (say average mpg) then press the upper part of the toggle switch marked RESET/CLEAR and hold it for about four seconds, this will display A or " B resetting" depending on which trip you are currently in, then everything on that trip is reset to zero (mileage/mpg/ave.speed etc). I use A for the full tank recording and B for individual journeys that I wish to record.

Jul 21, 2011 | 2000 Jaguar S-Type

1 Answer

How to use computer of average comsuption, average speed, ext temp ?


if my memory serves me right,if you zero all the readings before your trip then when you get to your destination you can read off the readings.thats it.(ext temp dont have a clue,except its ON permanently)

Nov 04, 2010 | 1978 Ford Granada

2 Answers

Hey, was wondering what the message center display symbols and what they mean, lost my manual


There are five trip computer displays which may be stepped through by pushing the MODE button. The information will appear in the following order:

D AVG ECON (Average Fuel Economy): This shows the average fuel economy since the last reset.

D INST ECON (Instantaneous Fuel Economy): This shows fuel economy for the most recent second of driving.

D RANGE (Trip Range): This shows the estimated distance that can be traveled with the remaining fuel. The fuel economy used to calculate range is based on the last few hours of driving. When in a low fuel condition, LO is displayed.

D FUEL USED (Trip Fuel Used): This shows the accumulated fuel used since the last reset.

D AVG SPEED (Average Speed): This shows the average speed since the last reset.


You can download a replacement Owner's Manual here: 2002 Chevrolet Impala Owner's Manual (PDF file from www.gmownercenter.com)

Oct 05, 2010 | 2002 Chevrolet Impala

1 Answer

2003 Nissan Maxima SE tachometer clock


Its not a clock its just calculates the time it took to make trip. The display at the bottom of the tachometer area is a "TRIP COMPUTER". It shows OUTSIDE AIR TEMPERATURE, DISTANCE TO EMPTY, AVERAGE FUEL COMSUMPTION, AVERAGE SPEED and JOURNEY TIME. Press the "TRIP" button on the steering wheel to change through the modes. Holding the "TRIP" button for more than one second will reset the mode.

Dec 20, 2009 | 2003 Nissan Maxima

3 Answers

How 2 turn off "oil change required" lite


Ford Explorer, Mercury Mountaineer, 2002-06

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the Message Center, press the SET UP control to access the System Check mode. Press and release the RESET button to display “OIL LIFE % HOLD RESET NEW” is displayed. Press and hold the RESET button for 2 seconds until “IF NEW OIL HOLD RESET” is displayed. Press and hold RESET button until “OIL LIFE SET TO 100%” is displayed.

Ford Five Hundred, Freestyle, Mercury Montego 2005-06 Tap the ODO/TRIP button to toggle the display between the odometer and trip odometer. Tap on the ODOiTRIP button again to toggle the display between the trip odometer and OIL LIFE % display. Press and hold the ODO/IRIP button for 2 seconds or more to display OIL LIFE 100%. Your oil life in now reset.

Good luck and print this and keep it in the glove box. Keep me posted if you have any other questions

Nov 04, 2009 | 2002 Ford Explorer

Not finding what you are looking for?
2005 Volvo S60 Logo

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...