Question about Ford Escape

1 Answer

How long will it take to install a exhaust manifold on a 05 ford escape

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 3,400 Answers

With proper tools and without breaking any bolts and having gaskets handy, about an hour.

Posted on Apr 04, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2005 ford escape xlt v6 awd. had a diagnostic test done at the dealership. said 2 of the 3 converters are clogged. they said I need a complete new exhaust system at a cost around 4000 bucks. any thoughtful...

get a second opinion you dont need the whole exhaust system---even if it the 2 manifolds have to be changed - thats a lot of money - there is a cat incorporated with each exhaust manifold so that would mean replacing the manifolds if both cats were bad thats both manifolds if your willing to do the work yourself you can change them the manifold/ cats sell on ebay new for under 200

Aug 15, 2013 | 2005 Ford Escape

1 Answer

On my 05 Chevy Equinox there is antifreeze pouring out from the exhaust manifold bottom boat on the passenger side what could it be what could it be it be

If you have an internal leak in that location the coolant will be most likely escaping via a crack in the cylinder head. You should check more closely to see if it is actually escaping via the cylinder head gasket between the head and engine block.

Most likley you will now have coolant escaping into the lubrication system so check your engine oil for coolant contamination.

Dec 25, 2012 | 2005 Chevrolet Equinox

1 Answer

How to remove exhaust manifold on a ford escape xlt do you have to remove engine mounts

You should be able to remove it without removing the mounts. You can get detailed instructions by registering (for free) at Your registration gives you access to several DIY repair manuals.

Dec 21, 2010 | 2002 Ford Escape

1 Answer

Where is the crank position sensor located on the 2002 Ford Escape? Will I need a rubber O ring or paper spacer?

The Crankshaft Position Sensor (CKP):
4 CYL - located on the front of the engine, near the flywheel end of the block. remove exhaust manifold, disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket req'd. torque to 62 inch-pounds
6 CYL - located next to crankshaft pulley - remove right wheel, remove lower right splashshield. disconnect electrical connector, remove bolt. installation is reverse of removal, no gasket req'd. torque to 89 inch-pounds

Dec 17, 2010 | 2002 Ford Escape

1 Answer

2004 ford escape engine emission light on lunges while idleing

I have found this to be a common problem on 2001-2006 V6 Ford Escapes. In 99% of these cases the problem is the Catalytic Converter. The V6 has three in-total, one per exhaust manifold, and one after the Y connection. This third catalytic converter is the one that always gets clogged. Another clue to it's failure is a loss of power and a increase in fuel consumption. The later 2006-2008 have a redesigned exhaust system. Hope that helps.

Dec 16, 2010 | 2004 Ford Escape

2 Answers

2004 ford escape exhaust manifold torque specs?


Fig. Left side exhaust manifold bolt torque sequence-3.0L engine


Fig. Right side exhaust manifold bolt torque sequence-3.0L engine

Both cases, exhaust manifold and new gasket, torque the bolts to 15 ft. lbs. (20 Nm).

Good luck (remember to rate this answer).

Oct 22, 2010 | 2004 Ford Escape

1 Answer

Ford Triton V-10 engine backfired and now make an exhaust escaping sound that I cannot locate where it comes from

hmm. sounds like a valve got stuck open and blew a manifold gasket? I would check all your exhaust manifold gasket and your collecter gasket. If you continue to have backfire issues you may have a sticky valve.

Apr 14, 2010 | 2001 Ford Expedition

1 Answer

I have a 2003 Ford Escape with a PO420 error code. When I accelerate, it sounds like air is coming from my engine. What is the problem and what should I do?

Here's what the code means, P0420 -- Catalyst System Efficiency Below Threshold (Bank 1).
Causes: Bad O2 senor, bad catalytic converter, and/or leaking exhaust manifold.

The error is coming from the O2 sensor number 1 between the exhaust manifold and the catalytic converter. The sensor itself may not be the problem. From what your describing is maybe a leak coming somewhere near the exhaust manifold. This would set off the P0420 code. Look around the exhaust manifold down to the catalytic converter for leaks that will leave black marks from burned fuel. If this can't be easily found, you may have to take the car in and have the exhaust hooked up to a smoke machine. This will inject smoke into the tail pipe and any leaks will be found by the smoke coming out of it.

Nov 16, 2009 | 2003 Ford Escape

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides