Question about Chevrolet Malibu

1 Answer

What is the proper routing - Malibu Chevrolet Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

Making sure the product; such as wire or hose,etc; is going along a safe path to its destination.
example; take the battery wire going to starter making sure it is not binding and making sure it does not get hot along the exhaust pipe or in the way of anything that can cause damage.

Posted on Apr 04, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced alternator and the serpentine belt isn't turning.


Serpentine belt has not been routed properly so there is not enough tension on the belt for it to turn. If you are sure that the belt is routed properly, then the belt tensioner is defective.

Nov 14, 2015 | Cars & Trucks

1 Answer

How do I change serpentine belt for a Toyota 2005 1.8 liter


check under the hood for diagram sticker that shows the routing of the belt. There is a idle pulley on a tension spring that keeps the belt taught. You must take pressure off the belt with long handled socket rachet or bar that fits in the tension bracket "fixed" bolt You push down to release the spring tension and pull the belt off ... To install you do the opposite.. be sure you have the belt properly seated on each pulley and route it according to the diagram . It helps to draw a picture of the routing before you start to insure proper installation.

Feb 12, 2015 | 2005 Toyota Celica 1.8

1 Answer

What is the belt routing for a ford 500


You can find the proper routing, by looking for the serpentine diagram, normally found on underside of hood or on radiator support in engine compartment

Sep 02, 2014 | 2005 Ford Five Hundred

1 Answer

Johndeere gx75 drive belt diagram


I broke a drive belt on my gx75 and need to know proper routing and installation for new one AmanStino Ultra Slim Lightweight Smart shell Stand Cover with Auto Wake...

Jun 15, 2012 | Cars & Trucks

1 Answer

I need a belt routing diagram for an1988 toyota landcruiser


Andy,I would suggest that you check the radiator cover or inside the hood for a label that shows the fan belt routing or AUTOZONE.COM repair section for the routing of the belt or go to your nearest toyota dealership for a copy of the routing. If all else fails check autozone for a Haynes manual to see the proper routing.

Nov 09, 2011 | 1988 Toyota Land Cruiser

1 Answer

I broke the belt on the front of the engine on the right side if you are facing the the engine and i was wondering what belt that was and how expensive it is to fix it


REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to be sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.
  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, be sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1?2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently so it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from under the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and be sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment.

prev.gif next.gif

Nov 05, 2010 | 1996 Oldsmobile Aurora

1 Answer

I need to know how to remove an A/C compressor pulley on a 2000 Mazda B3000, in order to route a new surpentine belt.


3.0L And 4.0L Engines
  1. Disconnect the negative battery cable.
  2. With the vehicle in neutral, position it on a hoist.
  3. Remove the splash shield.
  4. Rotate the accessory drive belt tensioner clockwise for 2001-2004 models and counterclockwise for 2005-2006 models. Remove the belt.
  5. To install, reverse the removal procedure.

Serpentine Belt
All Navajo and B Series Pick-up engines utilize one wide-ribbed V-belt to drive the engine accessories such as the water pump, alternator, air conditioner compressor, air pump, etc. Because this belt uses a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than on engines where accessories are pivoted and bolted in place for tension adjustment, such as the MPV. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked" all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys.

d7c3ada.jpg

Fig. Belt routing diagram-3.0L engines




a03a004.jpg


Fig. Belt routing diagram-4.0L engines


Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.
  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys.
Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing diagrams. If for some reason a diagram does not match (you may not have the original engine or it may have been modified,) carefully note the changes on a piece of paper.
  1. For tensioners equipped with a 1 / 2 inch square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.

  1. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioners internal parts.
  2. Now finish removing the belt from the other pulleys and remove it from the engine.
To install:
  1. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  2. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  3. Once the belt is installed, take another look at all the pulleys to double check your installation.
  4. Connect the negative battery cable, then start and run the engine to check belt operation.
  5. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range.

Hope helps (remember rated and comment this).

Sep 07, 2010 | Mazda B3000 Cars & Trucks

1 Answer

I need an Idler pulley or the pulley that runs air conditioner belt as well as the belt for the power steering


OK.
If your idler pulley is bad then unbolt it and while you're at it replace the power steering belt.

REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.
  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1⁄2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range. Fig. 1: Often the underhood label will display the serpentine drive belt routing 88231p43.gif
    Fig. 2: Relieve the belt tension by pivoting the automatic tensioner away from the belt, then remove the belt 88231p44.gif
    Fig. 3: Verifying serpentine belt alignment in the pulley 79244g60.gif
    Fig. 4: Fig. 1 Accessory V-belt routing — Tracker 1.6L engine with A/C 93024g03.gif
    Fig. 5: Fig. 2 Accessory V-belt routing — Tracker 1.6L engine with A/C and P/S 93024g04.gif
    Fig. 6: Fig. 3 Accessory V-belt routing — Tracker 1.6L engine with P/S 93024g05.gif
prev.gif next.gif

Jun 26, 2010 | 2000 Chevrolet Tracker

1 Answer

Belt replacement diagram 2000 mazda mpv


REMOVAL & INSTALLATION Because serpentine belts use a spring loaded tensioner for adjustment, belt replacement tends to be somewhat easier than it used to be on engines where accessories were pivoted and bolted in place for tension adjustment. Basically, all belt replacement involves is to pivot the tensioner to loosen the belt, then slide the belt off of the pulleys. The two most important points are to pay CLOSE attention to the proper belt routing (since serpentine belts tend to be "snaked'' all different ways through the pulleys) and to make sure the V-ribs are properly seated in all the pulleys. Although belt routing diagrams have been included in this section, the first places you should check for proper belt routing are the labels in your engine compartment. These should include a belt routing diagram which may reflect changes made during a production run.
  1. Disconnect the negative battery cable for safety. This will help assure that no one mistakenly cranks the engine over with your hands between the pulleys, and that the cooling fan cannot activate while servicing the belt(s). NOTE: Take a good look at the installed belt and make a note of the routing. Before removing the belt, make sure the routing matches that of the belt routing label or one of the diagrams in this book. If for some reason a diagram does not match (you may not have the original engine or it may have been modified), carefully note the changes on a piece of paper.
  2. For tensioners equipped with a 1⁄2 in. (13mm) square hole, insert the drive end of a large breaker bar into the hole. Use the breaker bar to pivot the tensioner away from the drive belt. For tensioners not equipped with this hole, use the proper-sized socket and breaker bar (or a large handled wrench) on the tensioner idler pulley center bolt to pivot the tensioner away from the belt. This will loosen the belt sufficiently that it can be pulled off of one or more of the pulleys. It is usually easiest to carefully pull the belt out from underneath the tensioner pulley itself.
  3. Once the belt is off one of the pulleys, gently pivot the tensioner back into position. DO NOT allow the tensioner to snap back, as this could damage the tensioner's internal parts.
  4. Now finish removing the belt from the other pulleys and remove it from the engine. To install:
  5. While referring to the proper routing diagram (which you identified earlier), begin to route the belt over the pulleys, leaving whichever pulley you first released it from for last.
  6. Once the belt is mostly in place, carefully pivot the tensioner and position the belt over the final pulley. As you begin to allow the tensioner back into contact with the belt, run your hand around the pulleys and make sure the belt is properly seated in the ribs. If not, release the tension and seat the belt.
  7. Once the belt is installed, take another look at all the pulleys to double check your installation.
  8. Connect the negative battery cable, then start and run the engine to check belt operation.
  9. Once the engine has reached normal operating temperature, turn the ignition OFF and check that the belt tensioner arrow is within the proper adjustment range. Fig. 1: Often the underhood label will display the serpentine drive belt routing 88231p43.gif
    Fig. 2: Relieve the belt tension by pivoting the automatic tensioner away from the belt, then remove the belt 88231p44.gif
    Fig. 3: Verifying serpentine belt alignment in the pulley 79244g60.gif
    Fig. 4: Fig. 1 Accessory V-belt routing (alternator) — Mazda MPV 3.0L engine 79244g67.gif
    Fig. 5: Fig. 2 Accessory V-belt routing (power steering) — Mazda MPV 3.0L engine 79244g66.gif
    Fig. 6: Fig. 3 Accessory V-belt routing (A/C compressor) — Mazda MPV 3.0L engine 79244g65.gif
prev.gif next.gif

Jul 08, 2010 | 2000 Mazda MPV

1 Answer

I need routing guide for serpentine belt for 2002 Dodge Ram 1500 Sport Quad cab 4.7 L v-8, Diagram on truck is damaged.


HI. I have located a good diagram. Kindly follow to assist with the proper routing. Use caution when installing your belt. This is the routing for your engine specs.
3a673c6.jpg




Feb 01, 2010 | 2001 Dodge Ram 1500 Truck 2WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...