Question about Chevrolet Impala

Open Question

2011 IMPALA REAR SEAT HEAD REST REMOVAL? - Impala Chevrolet Cars & Trucks

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

polarcycle
  • 1392 Answers

SOURCE: 2005 Jeep Grand Cherokee rear seat removal

For the seat bottom, you just need to pull it up. The seat backs would have to be unbolted.

Posted on Mar 06, 2009

bad_dog1
  • 104 Answers

SOURCE: GS350 rear seat removal

You can remove your rear seat cushions if you place your hand under the seat cushion you should be able to feel a hook. lift the seat up a little bit and you should be able to release the hook.

Posted on Mar 15, 2009

  • 1 Answer

SOURCE: Need to remove head rest to put on seat covers

I looked into new headrest for my 2005 Grand Cherokee with the monitors installed in them. I had mine off but couldn't remember how i did it. But I got the instuctions from the the company with the new headrest and they linked me to a video online. The company was on ebay. I remember that it was really simple

Posted on May 04, 2009

  • 1 Answer

SOURCE: cannot get adjustable head rest off the seat

On the plastic pieces surrounding the insertion hole on top of the seat back,there is a very very tiny hole on the side of this piece of plastic. You need to insert a rigid piece of wire or a very fine nail of some kind into this small hole and push until you feel it give, then pull up on the headrest. it should come out. You have to do this on each of the two insertion holes. It's easier with two people.

Posted on May 13, 2009

smartr10U
  • 1305 Answers

SOURCE: remove rear seat impala2007

To remove the rear seat, pull up on the front of the seat bottom, it should be hooked in place by spring type clips. After you get the front edge up, pull out the seat. This should expose the bolts/screws that hold the seat back in. Look below and there should be a couple of screws holding the seatback to the car body. Remove these and then you can pull the seat back out of the car.
K

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove rear headrests?


Tracy, Some just pull straight up and out, there may be a pin hole, lever or button just under head rest which will release and allow head rest to be pulled up or pushed down, it does take some force as they do like to get stuck.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Headrest Removal Pinhole Release Car Seat Cover Installation

Removing Rear Headrest Center Volkswagen VW Passat 2012 2015

How to remove the headrest in 2011 150 Supercrew

2007 Chevy Uplander Head Rest Removal


Mar 23, 2016 | Cars & Trucks

1 Answer

My second row seat wont stow.


sounds like a cable has broke in the back of the seat or a a metal rod had come adrift or broke ,ask a local mechanic to have a look for you .

Mar 02, 2015 | 2011 Chrysler Town and Country

2 Answers

Reset 2011 jeep liberty head rest


There is a little side button on side of hole where head rest connects to seat press it in and wiggle the head rest down or up into place.,.????????

May 30, 2014 | 2009 Jeep Compass

1 Answer

How can I fold down 2011 impala rear seat?


https://www.chevrolet.com/content/dam/Chevrolet/northamerica/usa/nscwebsite/en/Home/Ownership/Manuals_and_Videos/02_pdf/2011_Impala_Owner_Manual.pdf Look on 3-8 for instructions on how to fold down the rear seat only if your car is equipped with fold down seats. Not all Impalas have this feature.

Nov 08, 2012 | 2011 Chevrolet Impala

1 Answer

How to fold the rear seats in malibu 2011?


You should notice a looped strap of cloth next to the head rest at the top of the seat. That is the release for the seatback lock. Simultaneously pull up on the strap and pull the head rest forward to fold the seat forward. The seats are split 60/40, so each seat has its own release looped strap.

Jul 17, 2012 | 2011 Chevrolet Malibu

1 Answer

How can I remove the center rear headrest from my 2011 Impala? It is blocking my view and I am afraid could cause an accident.


Pull up on it till it stops. then take a pointed punch and stick in the hole at the base of the rod. While pushing in on the punch, pull up on the head rest.

Feb 26, 2011 | 2011 Chevrolet Impala

1 Answer

We need to remove the drives side head rest to install a seat cover, but we cannot figure out how to remove the head rest. How do you remove the driver's side head rest?


Head Restraints Removal
  1. Unscrew front seat head rest guide rod retainers (610A18) .
  1. Pull up on front seat back head restraint (611A08) . Compress foam in area of front seat head rest guide rod sleeves (610A16) .
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves .
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve .

    Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves .
  1. Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint .

9a4d433.gif

Aug 21, 2010 | 1998 Ford Taurus

1 Answer

How do you remove the headrest on a 1996 ford crown victoria?


Head Restraints Each front seat is equipped with dual-post design front seat back head restraint (611A08). The front seat back head restraint is installed as follows:
  • It travels on dual posts which have notches to engage a spring-loaded catch in the guide.
  • The front seat back spring assembly retains the front seat head rest guide rod sleeve (610A16).
  • The front seat back head restraint is adjustable from its normal position to a raised position of approximately 25 mm (1 inch).
  • Pull up on the front seat back head restraint to raise it. Pushing down will return it to its normal position.
----------------------------------------------------------------------------------------------

Removal
  1. Unscrew front seat head rest guide rod retainers (610A18).
  1. Pull up on front seat back head restraint (611A08). Compress foam in area of front seat head rest guide rod sleeves (610A16).
  1. Remove front seat back head restraint positioning springs. Pull front seat back head restraint up and out.
Installation
  1. Slide front seat head rest guide rod retainers onto front seat back head restraint posts.
  1. Compress foam in front seat head rest guide rod sleeve area. Install positioning springs on front seat head rest guide rod sleeves.
  1. Insert front seat back head restraint posts (notches on posts facing rearward) into front seat head rest guide rod sleeves and push down to engage positioning spring.
  1. Tighten front seat head rest guide rod retainers onto front seat head rest guide rod sleeves.
  1. NOTE: Front seat back head restraint must operate smoothly throughout its range of travel, must remain in any fixed position, and must not be freely removable from the seat back. If any of these conditions are not met, check for proper installation of positioning spring onto front seat head rest guide rod sleeve.

    Adjust front seat back head restraint by applying hand pressure, either up or down, to center area of front seat back head restraint.

Mar 01, 2009 | 1996 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

328 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...