Question about 2002 Volvo S60

Open Question

I HAVE ERROR CODE P1630 - 2002 Volvo S60

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Cobalt LS. codes P1630 passlock module and code P0315 cranck shaft relearn. It starts and dies after couple of seconds. replaced both without any luck. Any ideas?


Does the dash show the theft light/picture?If so turn the key to on and leave it on until it relearns the key chip.

Jul 09, 2017 | Cars & Trucks

1 Answer

2001 Cadillac debille security light stays on some times flashes but runs how do you find what resistanc the chip has with a meater and were you put it. to by pass


There is no resistance you can check , no place to by-pass anything . If the security light is on have it checked for DTC'S - diagnostice trouble codes . This will say what to check !

DTC B2734
DTC B2960
DTC B3031
DTC B3055
DTC P1630
DTC P1631

Autozone , napa , advance , pep boys , none of these can check for these codes , Dealer !

When an ignition key is inserted into the ignition lock cylinder, the transponder embedded in the head of the key is energized by the exciter coils surrounding the ignition lock cylinder. The energized transponder transmits a signal that contains its unique value, which is received by the theft deterrent control module. The theft deterrent control module then compares this value to a value stored in memory (learned key code). If the value is correct the theft deterrent control module sends the enable password via the serial data circuit to the powertrain control module (PCM).

Mar 24, 2017 | Cadillac Cars & Trucks

1 Answer

How ti reset or fix a P1630 error code on a Isuzu KB300 TDI Anyone please


welcome to USA forum
the country with not one
KB truck
in fact are EPA illeggal here. but not in AFRICA
for faster service, post to African forums>?

we have no cars, no books or parts here for KB of any kind.
sorry

google KB truck forums...

Mar 10, 2017 | Isuzu Cars & Trucks

2 Answers

2006 holden rodeo with 3 ltr Isuzu engine. Will run and drive and then stop with error code p1630a. If you pump priming pump and hold throttle down it will start and run for a while.


P1630 "Theft Deterrent Learn Mode Active", this causes a stall and the hard start. You may have a problem with the control module.

Aug 31, 2016 | Isuzu Cars & Trucks

1 Answer

I have mitsubishi canter.it has p1630 code.how to fix it.thanx


Fault code p1630, internal damage, no drive to injection pump

Aug 15, 2016 | Mitsubishi Cars & Trucks

1 Answer

I have a 2001 Toyota Ipsum 240e. The engine check light goes off when I disconnect the battery terminal. The light will not come on when the engine is run as long as required but once it is switched off...


You should have the error code read from the vehicle's computer (a code scanner is needed for this). If you constantly are disconnecting the battery, some manufacturers program an error code in the computer indicating that the battery has been disconnected within the last XX number of starts. If the code is P1600 or P1630, this is probably your problem. If you're disconnecting the battery for security reasons, either install an aftermarket security/anti-theft system or realize that the check engine light will keep coming on.

Sep 29, 2013 | 2001 Toyota Sienna

1 Answer

How do you reset the security light on a 2005 chevy cobalt?


There is no reset , if security light is lit there is a problem with the anti-theft system .Should have it checked for DTC'S - diagnostic trouble codes . Could have 8 different B - codes
DTC B0685 DTC B2955 DTC B2960 DTC B3031 DTC B3033 DTC P1626 DTC P1630 DTC P1631
You would need a professional type scan tool to read these type codes , not an OBD 2 code reader .

Apr 14, 2012 | Cars & Trucks

1 Answer

How do i replace ign. switch on a 99 alero


TO REMOVE IGNITION.FIRST TURN OFF RADIO.TO KEEP FROM LOCKING IT OUT.REMOVE NEGATIVE BATTERY CABLE.WAIT 20 MINUTES.THIS WILL DISABLE AIRBAGS.ALLOW THEM TO DISCHARGE.NOW YOU HAVE TO REMOVE THE INSTRUMENT CLUSTER.REMOVE THE TWO SCREWS SECURING THE IGNITION SWITCH.PUSH THE SWITCH ABOUT 1 INCH STRAIGHT BACK TO CLEAR THE MOUNTING BRACKET THEN LIFT IT UP AND OUT FROM BEHIND THE INSTRUMENT PANEL.DISCONNECT THE IGNITION SWITCH ELECTRICAL CONNECTORS AND THE IGNITION INTERLOCK CABLE.USING THE KEY TURN THE LOCK CYLINDER TO RUN AND PRESS IN THE PIN TO RELEASE THE CYLINDER THEN WITHDRAW THE CYLINDER WITH THE KEY.THE CYLINDER MUST BE REMOVED TO REPLACE IGNITION SWITCH BECAUSE YOU HAVE TO DISCONNECT WIRE TO THE IGNITION SWITCH. IN ORDER FOR CAR TO START YOU HAVE TO REPROGRAM NEW IGNITION SWITCH TO THE BCM AND PCM.TO DO THIS.TURN IGNITION SWITCH TO THE ON POSITION WITH ENGINE OFF FOR 10 MINUTES WATCH THE SECURITY LIGHT. WHEN SECURITY LIGHT EXTINGUISH.TURN OFF SWITCH FOR 5 SECONDS THEN START THE ENGINE.IF STILL DONT WORK TRY THIS PROCEDURE TWO MORE TIMES.IF YOU GET CAR RUNNING CHECK ENGINE LIGHT TURN ON CHECK FOR CODES P1630 P1631 P1632 USE CODE SCAN TO ERASE CODES IF CODES REMAIN LET DEALERSHIP CHECK IT OUT.THEY WILL HAVE TO ERASE CODES AND REPROGRAM THEFT SECURITY SYSTEM.

Jan 30, 2011 | 1999 Oldsmobile Alero

1 Answer

Mercedes e320 saloon diesel error codes p1630 AND p1617 Can't find date on these, anyone know? Bruce


P1617 Control Module Fault Or Control Module Not Coded
P1630 Drive Authorization Signal

It sounds like there's an issue with your Car's computer

Sep 24, 2009 | 2005 Mercedes-Benz Mercedes Benz E320 Cdi

Not finding what you are looking for?
2002 Volvo S60 Logo

Related Topics:

416 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...