Question about Daewoo Lanos

4 Answers

Starter spins but will not engage - Lanos Daewoo Cars & Trucks

Posted by on

  • amandabishop Apr 03, 2011

    they check the starter at the parts store and said it was good. could the battery being bad cause starter to not engage

×

Ad

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 76 Answers

This could be a few problems that cause this,

1. your battery could be weak and not have enough juice to engage the starter solenoid

2. the bendix could be messed up

3. this is probaly the most common problem, the starter solenoid went out

the best course of action would be to have your battery load tested, and if its fine, replace the starter

Posted on Apr 03, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 638 Answers

I would have the starter replaced, because it sounds like the bendix inside the starter is not kicking into the flywheel in order to start your vehicle, hope that this has been helpful to you.

Posted on Apr 03, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 844 Answers

Bad starter selonoid or starter bendix, I will say selonoid

Posted on Apr 03, 2011

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 388 Answers

The starter solenoid which pushes the starter drive into position to engage the flywheel will need to be replaced.

Posted on Apr 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2003 ford focus zx3 2.3l auto.. starter needed replaced due to test of solenoid wasnt working bench tested.. installed new starter..wired it up same.. now turn key amd i can hear starter motpr spin bit...


Yes, it is possible for the starter to spin without the solenoid engaging. The solenoid pushes the spring loaded gear forward to engage the flywheel.
You need to crawl back under your vehicle and ensure you've properly attached all wires. It should look similar to this:
starter-d053pipvg1eiz5wan5nws05s-1-0.jpg If these wires are properly attached, then check for power and/or damage to wires. The secondary will only energize when the ignition switch is engaged, so you'll need help (test when not attached to starter).

Jan 23, 2018 | Ford Cars & Trucks

1 Answer

Starter spins, but,will not engage,same as the one i repaced


You need to check for worn or broken gear teeth on the flywheel ring gear.

Mar 06, 2013 | Cars & Trucks

1 Answer

Replaced starter in 2002 tundra, now the starter spins but does not engage


sounds like you need to shim out the starter so the bendex gear in the starter engages with the flywheel/flexplate. as long as the bendex gear in the starter comes out the casing and spins shimming it will take care of that problem

Mar 03, 2013 | Cars & Trucks

1 Answer

92 honda civic hatchback new starter spins does not engage flywheel, could it be a fuse


unlikely as the motor spins. It appears that the motore solenoid is allowing the motor to spin before engaging the teeth in the ring gear. ON a lot of starters the pivot pin is adjustable to allow for correct engagement.Remove the starter and check that the solenoid is fact connected to the clutch part of the starter. Check that you have the correct starter for the engine

Jan 19, 2013 | 1992 Honda Civic

1 Answer

My starter spins but but doesn't engage the fly wheel. Solenoid or starter?


starter, take out and try across battery and it should whirr and jump out as if connecting with flywheel, if no spray the whole starter with WD40 inside and leave overnight. worked for me.

Apr 27, 2012 | Cars & Trucks

1 Answer

I need a starter solenoid wiring diagram for 1985 ford f150


Check the website for Autozone to get wiring diagrams free. If starter spins but doesn't engage, it is a bad starter drive located on the shaft of your starter. The solenoid is only there to spin the starter on a Ford. The centrifugal force engages the starter gear.

Jan 10, 2018 | 1985 Ford F150

1 Answer

2000 chevy impala, starter spins but does not engage


if the starter spins but does not engage flywheel. then its the starter solinoid thats bad. its on top of starter, when key is turned to start, the solinoid is activated, and it pushes the gears out to make contact with flywheel to start vehicle. so the solinoid just spins with out kicking out to flywheel. change solinoid or get another starter. have a good day !

Nov 27, 2010 | 2000 Chevrolet Impala

2 Answers

When i start the 95 tahoe, i hear a spinning noise. starter is not engaging the engine. it's a brand new starter.


Hello there:
The spinning that you are hearing is the bendix spinning there is a
engagement spring that forces the bendix to engage on the flywheel
If this spring is weak or broke the bendix cant engage furthermore if the teeth on the bendix are broke or chipped or the teeth on the fly wheel are chipped or broke -this will not allow the bendix to engage or start to turn the motor ok so i would have these things checked out ok?
I hope that this is very helpful for you best regards
michael

Nov 18, 2009 | 1995 Chevrolet Tahoe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

320 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78289 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...