Question about 2004 Toyota Sequoia

1 Answer

I have a 2004 Toyota Sequoia. I have lost power to the 12V connections in front (2) and the single near the rear hatch. The primary 12V connection (near the ash tray) still has power. The fuse box labels don't tell me enough to see which one serves these 3 12V outlets. I checked them all. I have pulled all the fuses and looked at them and they all look good. Obviously one isn't. Any hints to which fuese serves those outlets?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Toyota Expert
  • 374 Answers

They are usually labeled power outlet or cig lighter, check the fuses with a test light or voltmeter, they may look good but may not have power to them .

Posted on Jul 18, 2017

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
trav1856
  • 57 Answers

SOURCE: 2004 corolla fuse box

open the driver's side door and look on the side of the dash. If it's not there, check the passenger's side on the center console. If not there, check under the hood.

Posted on Dec 02, 2008

  • 1861 Answers

SOURCE: No power to cigarette lighter/power outlet (front & rear)..

Replace the 15 amp ACC fuse that is in the fusebox under the dash. See if this eliminates your problem.

Posted on Dec 08, 2008

  • 1 Answer

SOURCE: I have lost all power to the rear hatch of my 2005

I had the same thing happen...I already had the rear door taken apart because the latch mechanism had failed and I was replacing that (not too bad a job: $100 part and 2 hours)...while I had the door apart I tried tapping on the window motor with hammer to get it working again...that did not seem to do anything. I then started looking at fuses.. There are 3 fuse boxes under the hood, and 1 panel by the driver's left knee. The top left fuse in the driver's left knee fuse box was labeled "TAIL". I pulled that one and even though it was not burned through...it looked a little funny (had some discoloration on the contacts like it had been getting hot). I replaced that and then shut the rear door and started up the engine. What do you know..everything works. I think it was likely the fuse...but who knows. Maybe this will work for someone else too.

Posted on Mar 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fill the rear washer fluid on a 2002 Toyota sequoia


On alot of SUV's, you have to open the back hatch or tailgate, and there is a washer fluid reservoir either in the door jam of the hatch, or inside the back of the truck.

Apr 27, 2012 | 2002 Toyota Sequoia

1 Answer

2004 Sequoia B2S1 o2 sensor - where is this located and is it easy to replace? Thank You!


Toyota Sequoia has 4 oxygen sensors... two on each side. The ones in front of catalytic are position one, and, after are position 2.

Bank 2 is on passenger side, Bank 1 is on driver's side.

Hope this helps (remember to rate and comment this free answer).

Sep 21, 2011 | 2004 Toyota Sequoia

2 Answers

I have lost all power to the rear hatch of my 2005 Toyota Sequoia. Rear defroster is out, power rear window is out, rear wiper is out. Is there a fuse to check?


I had the same thing happen...I already had the rear door taken apart because the latch mechanism had failed and I was replacing that (not too bad a job: $100 part and 2 hours)...while I had the door apart I tried tapping on the window motor with hammer to get it working again...that did not seem to do anything. I then started looking at fuses.. There are 3 fuse boxes under the hood, and 1 panel by the driver's left knee. The top left fuse in the driver's left knee fuse box was labeled "TAIL". I pulled that one and even though it was not burned through...it looked a little funny (had some discoloration on the contacts like it had been getting hot). I replaced that and then shut the rear door and started up the engine. What do you know..everything works. I think it was likely the fuse...but who knows. Maybe this will work for someone else too.

Jan 29, 2010 | 2004 Toyota Sequoia

1 Answer

Rear tailgate will not close because latch is not locking on 2004 Toyota Sequoia


You either have a rusted latch assembly, or a seized latch release cable, which connects to the release handle. Either can be the cause, this is a very common failure., Try some WD-40 on the latch, and see if you can work it with a screwdriver. If that does not help, you will need to replace the release cable.

Oct 19, 2009 | 2004 Toyota Sequoia

1 Answer

Broken rear hatch door handle on Toyota Sequioa


It sounds like the handle has become disconnected from the mechanism. You will have to remove the inner door panel and reattch. It is not a complicated or difficult job but if you get a professional it could cost upwards of $100.

Jul 16, 2009 | 2006 Toyota Sequoia

2 Answers

My rear hatch door handle broke i need to replace it. how do i replace it?


how do i get the rear gate panel off so I can replace the latch on the 2003 sequoia.

Jul 06, 2009 | 2002 Toyota Sequoia

2 Answers

Rear door latch replacement 2003 sequoia


Fig. The latch bracket shown is moved by loosening the mounting fasteners and sliding it as necessary. Matchmark the bracket to the door pillar before moving-1.8L Passat model shown

Jun 02, 2009 | 2003 Toyota Sequoia

1 Answer

2004 toyota sequoia front end shake


Replace the front rotors.
Refacing does not work on Sequoias. The metal removed to get the rotor "true" is usually below minimum safe thickness, and the vibration comes right back when it gets hot.

Oct 16, 2008 | 2004 Toyota Sequoia

Not finding what you are looking for?
2004 Toyota Sequoia Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...