Question about 2001 Honda Accord

1 Answer

Bleeding clutch slave cylinder

I have a 2001 honda accord dx. My clutch slave cylinder was leaking so I replaced it. Now it seems as if i cannot bleed the cylinder. I constantly pump the clutch and bleed the cylinder but I cant get any pressure on the clutch. Is there a special way to bleed this cylinder. I am really frustrated

Posted by on

  • 4 more comments 
  • yadayada
    yadayada May 11, 2010

    Open the bleeder at the slave and let it gravity bleed for 5 or ten minutes keep and eye on it do not let the fluid reservoir run dry, this should help, did you pre-bleed the cylinder before you replace it?? another thing master and slave should always be replaced as a pair, it may be debris from the master that caused the slave to fail.

  • Anonymous Mar 14, 2014

    replaced clutch and slave cylinder and cant get a pedal with pressure

  • Anonymous Mar 18, 2014

    remove and replace clutch slave cylinder

    emove and replace clutch slave cylinder

  • Anonymous Mar 18, 2014

    cost tand time to replace

  • Anonymous Mar 21, 2014

    no presure at clutch think its slave cylinder but cant see it ?

  • Anonymous Mar 21, 2014

    problem getting car into gear....have to pump clutch

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 275 Answers

If you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris

Posted on Nov 12, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bleeding hydraulic clutch


If you put in a new slave or master you need to bench bleed them first before installing or wont work

Jul 17, 2012 | 2003 Honda Accord

1 Answer

Have a 2001 honda accord just replaced master clutch cylinder and slave cylinder and clutch won't disengage. what could be the problem.


Did you bleed the clutch hydraulic system after you replaced the parts? It requires bleeding just like the brake system does.

Jul 05, 2011 | 2001 Dodge Ram 2500 Truck

2 Answers

Lost resistance on clutch pedal and hard to change gears also when topping up clutch fluid it does`nt last that much and leaks from slave cyclinder


If the slave cylinder is leaking, replace the slave cylinder. You are loosing hydraulic pressure in the clutch and is the reason why it is not engaging correctly.

Apr 13, 2011 | 2001 Honda Accord

1 Answer

2001 mercury cougar, master cylinder ran dry because slave cylinder below is leaking at the firewall. I filled the master cylinder and tried bleeding the clutch at the transmission until fluid stream...


No, you don't need to replace the clutch itself.
Don't be surprised if the slave cylinder replacement doesn't fix it.
Could be the master cylinder.

Sep 12, 2010 | 2001 Mercury Cougar

2 Answers

I have a 96 honda accord and changed the clutch master cylinder and the slave cylinder and bled the system there still is no clutch pressure


You need to PRE BLEED the master cylinder, or you may never get pressure. Parts houses sell little hoses for this purpose.

May 30, 2010 | 1996 Honda Accord

1 Answer

How to replace clutch slave on 1996 honda accord


first brake loose the line that feeds the slave cylinder. you will need a line wrench for this. then remove the 2 twelve millimeter bolts that hold the slave to the trans. remove the hydraulic line from the slave. reinstall in the reverse order(before installing slave break loose the 8 mm bleeder screw) then bleed the clutch by yourself or with an assistant. bleeding processes vary

Jun 18, 2009 | 1996 Honda Accord

1 Answer

2001 Honda Accord Clutch Issue


check the actual pedal and clutch linkage.  Also look for a fitting thats emitting air into the system.

Mar 24, 2009 | 2001 Honda Accord

2 Answers

My 1990 Honda Accord is not taking gear


Check the fluid level in the clutch master cylinder reservoir - it is probably low. You will probably have to bleed the system (similar to bleeding brakes), the bleeder screw is on the slave cylinder on the front side of the transmission. If the level is low, you should also check for leaks in the system while you're at it. Leaks from the master cylinder show up on the inside of the firewall and floor below where the push rod comes through the firewall. Leaks from the slave cylinder should be fairly obvious on the flexible boot.

Jan 27, 2009 | 1990 Honda Accord

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

Not finding what you are looking for?
2001 Honda Accord Logo

967 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...