Question about 2005 Ford F-150

1 Answer

2005 Ford F150 4x4 5.4 Problem with the Ford F-150 Cars & Trucks 2005 Ford F150 4x4 5.4 Ext. Cab Auto headlights door locks and remote keyless lock and unlock do not work anymore power is not killed to radio when key is shut off and door is opened.Driving down the hwy and all of a sudden dash lights and abou anything electrical started to flicker real bad and done this for about 15 min. and then none of the stuff worked as I described above all the irattic electrical stuff stopped and has not done it again but my auto headlights or daytime headlights don't work anymore. Headlights will work ok with manual use of headlight switch. Nothing works when headlight switch is in A position would like to get this problem taken care of without taking it to a Ford dealer. Thank you for any help with this

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 984 Answers

The single item that is common to all the symptoms is the BSM ( Body Security Module ) behind the rear seat back or cab panel ( depending if it is a std cab or supercab / supercrew ).

There are 4 fuses for the BSM, these are fuses # 6, 18, 40, 107 and 102.
Start by checking these fuses with a meter on both sides of the back with the little pin, using a known good ground ( there is one to the lower right hand corner of the fuse panel ).

The next thing I would check is the ground to the BSM itself, this is behind the rear seat back ( if a supercab / supercrew ) cab configuration.

removing the seat back looks hard, but it is really a 25 min job the first time.
2005 Ford F150 4x4 5.4 Problem with the Ford F-150 - sscullys_159.jpg
2005 Ford F150 4x4 5.4 Problem with the Ford F-150 - sscullys_161.jpg
sscullys_161.jpg
This is the location for releasing the clips. Took me a few trys to get the latch released the 1st time, but the next one went easy. Once the clip is released, stick a 2x4 covered in a sock2005 Ford F150 4x4 5.4 Problem with the Ford F-150 - sscullys_162.jpgback, so it does not relatch itself when you are doing the other side.
2005 Ford F150 4x4 5.4 Problem with the Ford F-150 - sscullys_163.jpg
This is the angle that you are shooting for, you can see there is a target that you are feeling for.
sscullys_163.jpg

Once you have the seat back out, getting the carpet off the back wall is easy. The BSM is the hump in the back wall covering, follow the ground wire to the lug, and make sure it is connected good, and it not broken at the connector on the BSM ( give it a slight tug ).

Hope it is one of the fuses, and you do not have to go digging in the back.

The symptoms by themselves have different solutions, I took the common item, so it could be a case of you really do have multiple problems. The autolamp one would be a burn pin at the connector if they are different issues, if the fuses and ground check good, while you have the seat back off, pull the connector and look at it, to see if the pins are burnt.

Posted on Apr 11, 2011

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4369 Answers

SOURCE: 2005 Ford F150 4x4 5.4

I think you have a bad lighting conrol module. Call a dealer parts department and ask if there is one in your truck and how much is it.
tascafordparts.com sells at discount.

gerry

Posted on Apr 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Changed battery in keyless remote and now doesn't start car or open doors


  • HOW TO - Change the battery and quick fix your car remote ...

    ? 9:32
    https://www.youtube.com/watch?v=KzCXGXCe0oc
    Sep 1, 2011 - Uploaded by tyreeztt
    Also if your remote isn't working with a new battery please check out this ... TO - Change the battery and quick fix your car remote / keyless entry ...

    Remote Key does not lock / unlock doors after battery change ...

    www.6speedonline.com/.../208274-remote-key-does-not-lock-unlock-do...
    Apr 17, 2010 - After I changed the battery, it would no longer lock / unlock the doors. ... I can start the call and all .. its just the door and trunk lock / unlock function that does not seem to work . ... now your fob is learned... the keyless entry goes into a "sleep" mode to preserve the batt.. if u do not use the ... Still don't work .

    how do i reprogram my lock remote to my car? i changed my ...

    www.cargurus.com > Questions > Hyundai > Tiburon

    CarGurusAug 17, 2009 - i change my battery an now my lock an un lock buttons dont work on my remote how o i reprogram it? ... I have a Hyundai 2003 Tiburon, and the followingworked for me, get ... However for a replacement keyless remote fob, you will have to go to ... And no, they don't do it for free (ranges from $30-$50 in my ...

    Top 5 Tips in Fixing a Keyless Remote ' eBay

    www.ebay.com > ... > Safety & Security > Keyless Entry Remote / Fob
    Key fobs that don't permit entry can be a major hassle for drivers, but fortunately, there... Drivers with a bit of basic electronics experience are often able to replace their ...After confirming that a remote is faulty, try replacing its battery. ... like "Jeep Wranglerkeyless remote," to find listings that will work with specific vehicles.

Jan 26, 2016 | 2005 Ford Freestyle

2 Answers

Changed battery and now remote doesn't work. it is on a 2005 ford freestyle


press the helpful button,there appears there is more then one type of remote, I think one has auto start and one does not.

owners manuals in the glove box and in there was the Ford Auto Start Remote booklet. For those of you who need to program a new auto start remote, you turn the ignition to the on position, push and hold the little over-ride button (mine is down on the left side kick plate near the hood release) for about 15 seconds, you will hear a chirp which means the system is ready to be programmed, just hit the lock key on your remote and the system will chirp acknowledging the remote has been programmed, continue to do this will all other remotes you have within I believe it was 20 seconds - then shut off the ignition and test your remotes. Worked perfectly for me.
OR

Free Do It Yourself instructions from your friends at Lessco Electronics

1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.
Link below
2005 2006 Ford Freestyle Factory Transmitter Remote Fob Programming

Jan 26, 2016 | Ford Cars & Trucks

1 Answer

How do I reset keyless door entry that is in lock out mode


Viper Keyless Entry Systems

https://www.viper.com/car/keylessentry/
Viper is the industry leader in keyless entry systems. Add the convenience of keylessentry to virtually any vehicle - even vehicles without power door locks!

Alarms, Remote Car Starters, Keyless Entry & Locks - JC ...

www.jcwhitney.com > Audio, Video & Electronics
20 out of 32 products in Alarms, Remote Car Starters, Keyless Entry & Locks ..... ofKeyless Entry & Car Alarms allow you to lock and unlock power door locks.
How to program your keyless entry keypad - Ford Ownerhttps://owner.ford.com/.../locks.../how-to-program...Ford Motor CompanyDiscover how to lock and unlock your doors and how to program memory settings that will adjust seats & mirrors for each driver.SecuriCode™ Keyless Entry Keypad - Ford Ownerowner.ford.com/.../locks.../securicode-keyless-entr...Ford Motor CompanyLearn how to set a 5 digit SecuriCode on the Ford keyless entry keypad. ... Sign out. Register/Sign In · Your Vehicle. Service & Maintenance. Service & .... vehicle's SecuriCode keypad to lock and unlock your doors without having to use a key. ... Thekeypad will go into an anti-scan mode if you enter the wrong code seven ...How Programming Your Keyless Entry Can Make ... - Ford Life

Jan 08, 2016 | Cars & Trucks

1 Answer

Auto headlights will not turn off


have the auto module in the light circuit tested as the problem apparently is in that unit.

Jan 19, 2014 | 2006 Ford Fusion

1 Answer

I own a 2005 Ford Five Hundred and I am trying to get my keyless entry to work.


I assume you are trying to program the remote. Here are the instructions. Your question is very vague.
1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in
RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will
cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

Oct 20, 2012 | Cars & Trucks

1 Answer

I lost my keyless remote, now i can't turn the alarm off


try locking and unlocking the drivers door with the key

Jun 30, 2012 | 2005 Chevrolet Trailblazer Ext

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

3 Answers

How do I reprogram the keyless entry keypad?


You can found the code on F-150 up under the dash. There is a sticker on a grey box. That is the code that you need to open the door. You can then use that code to program your own 5 digit code that you will remember.

For program your keyless pad (clic image), check the procedure in your 2006 Ford F-150 Owners Manual moz-screenshot.pngmoz-screenshot-1.png(page 108 and next).

ec44e90.jpg

Remember rated this help, good luck.

Feb 15, 2010 | 2006 Ford F-150

1 Answer

Hello!!! I am having trouble. This has happened one time before and I fixd it but I cant remember how in the heck I did it. Here is the prob...The doors will not lock or unlock by the buttons or the...


check the fuses to the CSM ( Central Security Module ) .

CJB ( aka Central Junction Box, cab fuse panel ) Fuse # 15 & 29
15 is the BPP ( Brake Pedal Position ) Switch, so that should be fine, unless you cannot get the truck out of park while running and the brake lamps don't work.
29 is the fuse to the CSM ( hot in start or run key positions ).

BJB ( aka Battery Junction Box, Engine Compartment fuse panel ) Fuse # 115 or 8. 115 is for the Supercrew body style and 8 is for the standard cab & SuperCab configuration.

This is for a build date after 2-OCT-2000 ( 2001 MY ).
Build date before 2-OCT-2000, the CSM is a RAP ( Remote Anti-theft Personality ), looks the same, same functions, but is not pin for pin compatible.
Fuses for this are CJB Fuse #8 and 15 and BJB Fuse #4.

With the CSM / RAP installed, the power door locks are controlled by the CSM/RAP, without the RKE ( Remote Keyless Entry ) installed, they are normal power door locks ( switch to the door lock direct ).

Worth a start checking the CSM / RAP fuse

Nov 18, 2009 | 2001 Ford F150 Styleside SuperCrew

Not finding what you are looking for?
2005 Ford F-150 Logo

955 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...