Question about Chevrolet C1500

1 Answer

What is the ignition timing for a 1993 cevrolet truck in degrees

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

It depends on what motor u have,,& if the motor needs to be in base timing...

Posted on Apr 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 chevy c1500 p/u v6, 4.3 liter, 5 speed manual trans wont start


check the valve timing after replacing the chain. check that you connected the ignition module to the coil. Check ignition timing as you may be out 180 degrees on the timing.

Apr 21, 2014 | 1993 Chevrolet C1500

1 Answer

Timing off how do i reset timing and distributor


1993 Nissan/Datsun Maxima 3.0L SFI SOHC 6cyl


The Ignition Timing15 Degrees

Sep 14, 2013 | 1993 Nissan Maxima

2 Answers

When setting the ignition timing on a 1991 ford ranger 3.0 were dose the rotor need to point, after number one or before number one? the engine is on top dead center


The engine timing markers down on the harmonic balancer/crankshaft pulley should be aligned with the timing indicator on the engine block to "0" degrees when the engine is in the compression stroke for the #1 cylinder, and this is TDC or "Top Dead Center". When something blows out of the spark plug hole that only means that the piston is coming up on TDC, but the crankshaft will still have to be turned until the timing markers are at "0" degrees. You should be sure that you do know how to properly align the timing marks to "0" degrees, and the timing marks must be set at "0" degrees before the distributor can successfully be installed.

Be certain that the timing marks are set at "0" degrees and on the compression stroke for the #1 cylinder, or the timing will be 180 degrees off when you install the distributor. This has to be precise and guessing will not get the distributor properly clocked in so that the ignition timing can be correctly set.

Once you are certain that the timing is set to "0" degrees "TDC", then mark the distributor housing where the #1 position on the distributor cap will be when the cap is installed on the distributor, so that the distributor housing shows a reference mark where the #1 position is, then the distributor should be installed so that the ignition rotor is pointing directly at the #1 position on the distributor housing, or just before the #1 position mark according to the rotation of the ignition rotor. The distributor should be able to turn and point the ignition rotor on either side of the #1 position mark to provide plenty of timing advance or ****** so that the ignition timing can properly be adjusted to specifications after the engine has been started.

Be sure that you follow the proper timing procedure for that vehicle and remove any timing spout connectors that are described in the set timing procedures

Also, be certain that you are actually using the #1 cylinder to set the engine to TDC and to actually time the engine with a timing light. Here is a firing order diagram that should also help to assist you. Let me know if you require any further assistance.






cab28d1.gif

Jun 17, 2010 | Ford Ranger Cars & Trucks

3 Answers

I need a fire timing order for a chevy astro van v6


THE FIRING ORDER IS AS FOLLOWS : 1-6-5-4-3-2.
CYLINDER NUMBERS (front-to-rear) :
LEFT (driver side) 1-3-5
RIGHT (passenger side) 2-4-6

To set ignition timing, ensure that engine is at operating temperature, (190 degrees or above), bypass EST (electronic spark timing) by unplugging the single tan wire with a black stripe from the distributor. Ignition timing should be set at 0 degrees or TDC (top dead center). If not, loosen distributor hold down bolt and adjust, then retighten.

Mar 05, 2010 | 1993 Chevrolet Astro

2 Answers

1997 Cevrolet Cavalier 2.4 liter engine leaks antifreeze


If it is the water pump it will have a rad hose attached to it. There is supposed to be a small hole in the bottom of the water pump. When it starts leaking, it's time to replace the pump. You can do it yourself. A few wrenches and a couple hours is all you need. If you are unsure pick up a Haynes manual for your car when you get the new pump.

Jul 05, 2009 | 1997 Chevrolet Cavalier

1 Answer

1993 Escort 1.9L pinging


U can fix this by removing the one time 3 degree timing ****** shorting bar which is located next to the ignition control module, this is a common problem.

Apr 26, 2009 | 1996 Ford Escort 4 Door

2 Answers

How can I set ignition timing for a 1993 Nissan pickup D21 2.4L


the mark to the right of the pully will be 0 .. it will be like this. 8 6 4 2 0

Apr 21, 2009 | 1993 Nissan Pickup

1 Answer

Timing ignition


Hello stacia_burch, my name is JShreader. Thank you for choosing fixya.com.

The Ignition Timing on this 1.0 L Engine is set to 5°±1°BTDC. I uploaded the procedure in .pdf format. You can download it by clicking HERE. I hope this helps you. If you have any more questions or need any more diagrams, please don't hesitate to ask...Thanks again, JShreader!




Mar 24, 2009 | 1993 Geo Metro

1 Answer

Don"t know the timing


check ignition timing with transmission in neutral with parking brake applied .
base timing is 10 degrees @ 800 rpm , with jumper wire installed between data link connector terminals TE1 and E1 .
advance timing is 8 degrees @ 800 rpm , with jumper wire removed from data link connector .

J5

Jan 18, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...