Question about 1992 Dodge Caravan

Open Question

1992 dodge caravan. need to replace the oil pan 3.0 liter. does the engine need to be lifted?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 160 Answers

SOURCE: RATTLING NOISE AT OIL PAN AREA ON 1998 DODGE RAM 1500 5.9 LITER

rod bearing , engine needs rebuilt

Posted on Nov 12, 2008

Ad
  • 1 Answer

SOURCE: how to replace serpentine belt?

how to remove and re-install serpentine belt?

Posted on Nov 20, 2008

c17hydro
  • 2984 Answers

SOURCE: What is the sequence for the bolts on oil pan, for

For the 2.8L there is no sequence. Torque for the bolts are 105 in.lbs.

For the 3.0L torque is 50 in.lbs. in sequence:




40be0ec.gif

30fedd0.gif
For the 3.3L and the 3.8L, no sequence but torque each bolt to 105 in.lbs.

Please don't forget to rate!

Posted on Jul 12, 2009

  • 1201 Answers

SOURCE: 1992 Dodge Dakota 3.9 liter 5 speed manual

75W/90 gear oil.

Posted on Aug 17, 2009

fixitriteman
  • 431 Answers

SOURCE: how do I replace the oil pan gasket on my 2003

oil pan this is the easiest I've see ... as the struts go never take the nut off the top center under pressure as a assembly strut with spring safer but you will need a alignment there is 3 nuts on top 2 bolts&nut bottom of strut brake hose is held 2 strut also

Posted on Mar 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need wiring diagram for 1992 dodge caravan with 2.5 liter, engine and body


Make sure you reconnected the ground strap on the cylinder head(my Dakota with the same engine did all kinds of crazy things when I put the engine back in and forgot to connect it).

Nov 26, 2013 | 1992 Dodge Caravan

1 Answer

Need to locate the starter on a 97 dodge grand caravan 3.3 liter engine.


the starter is located on the front of the engine if you stand in frt of the van the starter is to the right by the oil pan,slide under the front of the van and you will see it where the engine and trany come together. hope this helps.

Sep 05, 2010 | 1997 Dodge Grand Caravan

1 Answer

Need the wireing order for a 1992 dodge caravan in changing the termostate i removed the wires to reach the nuts marked them but the car runs bad must have them mixed up 3,3 liter engine caravan se


For the 3.3L:
Firing Order:

1-2-3-4-5-6
Cylinders:
(back of vehicle)
1--------3--------5
2--------4--------6
(front of vehicle)
Ignition Coil:
(back)
6---3
4---1
2---5

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Jul 13, 2010 | 1992 Dodge Caravan

3 Answers

Need to know the firing order of a 1996 dodge caravan 6 cylinder


Not sure what size of 6 cylinder you have so please pick the correct one for your motor size:

1996 Dodge Caravan
3.8 liter V-6 VIN "L"

ca44852.gif

1996 Dodge Caravan
3.3 liter V-6 VIN "R"

2253596.gif


1996 Dodge Caravan
3.0 liter V-6 VIN "3"



cbd54ee.gif

May 11, 2010 | 1996 Dodge Caravan

1 Answer

My check engine light comes on intermittently and when i stop the oil light comes on and dings I am told this could be an oil pump - how hard is this to fix on my vehicle - Dodge Grand Caravan 2000 3.8L V6


yes this is true it could be a oil pump but first check the oil level first. most oil pumps are inside the oil pan. and most pans can only be taking off by lifting motor up or the exagust off

May 04, 2010 | 2000 Dodge Grand Caravan

1 Answer

Change the oil on a 2000 Dodge Caravan


Jack up pass side.Put cardboard, BIG piece under engine just in case. Using a pan to drain the oil in put under oil pan drain plug. Remove drain plug with socket wrench. Let drain 5 min. Check the gasket on the drain plug, if bad replace with new gasket .99 cents to replace gasket only on plug. Put plug back in DO NOT OVER TIGHTEN the plug. Slide drain pan with drained oil to the front to remove oil filter. Using a filter wrench remove oil filter. Let drain. When installing new filter put a little new engine oil on the rubber gasket on the filter with your finger. Screw filter back on tighten with filter wrench. Fill van with oil from front valve cover opening.

Nov 21, 2009 | 2000 Dodge Caravan

1 Answer

I need to replace the oil pan on my 2002 Dodge Intrepid with a 3.5 Liter engine. What are the steps. Especially with the metal ubber pan gasket.


1.put car on a lift. 2.Drain oil. 3.make sure to have exact oil pan ready with seal in hand. 4.unscrew the bolts in a x fashon. 1-6 3-4 2-5 remove oil pan. 4.Clean all around where the oil pan used to be. 5.Attach new seal and oil pan. hand tighten all the bolts in a X fashon then tighten with a wrench or socket. 6.make sure oil drain plug is on good. 7. put new oil in typically 5 quarts. 8.put car on ground 9. All done.

Sep 02, 2009 | 2002 Dodge Intrepid

1 Answer

Need to replace oil pump assembly


Remove the Oil Pump
1.
Step 1

Drive your Dodge Caravan up onto ramps or lifts so you have room to work as you pull out the oil pump. You could also use a jack, but make sure you brace the front wheels and engage the parking break so the car doesn't roll.
2.
Step 2

Disconnect the negative battery cable on your Dodge Caravan. Drain the engine oil and coolant into separate pans. Take the vehicle off the ramps or lifts. Remove the accessory drive belts and use an engine support tool to hold the weight of the engine.
3.
Step 3

Take out the right engine mount and bracket. Take off the timing belt cover and loosen the bolts on the timing belt tensioner. Remove both the tensioner and the timing belt then raise the vehicle back on the ramps or lifts.
4.
Step 4

Take out the oil pan assembly and remove the oil pump pick-up and the O-ring. Take the crankshaft damper out with a good puller. Use a puller to also draw the crankshaft sprocket from the front of the crankshaft.
5.
Step 5

Loosen the bolts on the oil pump and take them off. Remember where they were since you'll need to replace them later. Unscrew the relief valve.
Install the New Oil Pump
6.
Step 1

Clean all the parts to remove contaminants and debris then install the inner rotor. Make sure the chamfer faces the cast iron oil pump cover on the back. Torque the bolts to 105 in. lb.
7.
Step 2

Install the relief valve, followed by the spring, gasket and cover cap. The cover cap should be tightened to 40 ft. lb.
8.
Step 3

Fill the rotor cavity with clean engine oil to prime it then insert a new O-ring seal into the oil pump. Put Mopar Gasket Maker or equivalent anaerobic type gasket sealer on the flange of the oil pump body.
9.
Step 4

Align the oil pump rotor flats with the flats on the crankshaft and install the pump slowly, tightening the fasteners to 20 ft. lb. Add the new front oil seal and install it with the spring side facing the inside of the engine. Even it out with the engine cover.
10.
Step 5

Install the crankshaft sprocket with the special sprocket tool. Put on the oil pump pick-up tube and O-ring and torque the bolt to 20 ft. lb.
11.
Step 6

Insert the oil pan and install a new oil filter. Lower your vehicle then install the timing belt and covers and crankshaft damper with a tool specialized for the 2 mm by 1.75 by 150 mm bolt. Tighten the center bolt to 105 ft. lb.
12.
Step 7

Put on the accessory drive belts and adjust them to the right tension. Put on the engine mount and bracket then take out the engine support tool.
13.
Step 8

Add fresh oil to the engine and refill the cooling system. Use a 50/50 mixture of clean, ethylene glycol antifreeze and water in the cooling system. Start your engine and check for leaks.

May 21, 2009 | 2000 Dodge Caravan

2 Answers

Have a serious oil leak.


the 3.0 liter engine was known to walk out cam shaft seals. there are covers over the camshaft gears that can be removed and you should be able to see if the seal has came out

Jan 31, 2009 | 2000 Dodge Caravan

1 Answer

Do I need oil pan w/ oil sensor hole?


look at the pan you got, if it has the one with the sensor hole, then go for the one with a sensor hole.

Dec 20, 2008 | 2005 Honda Odyssey

Not finding what you are looking for?
1992 Dodge Caravan Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...