Question about Chevrolet Colorado

1 Answer

2006 colorado running rough coad p0017 comes up

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,620 Answers

This a crank angle sensor code. Disconnect the cam shaft sensor momentarily this should cause the fault to temporarily disappear,If it does'nt its probably a bad crank angle sensor.

Posted on Apr 03, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2010 Chevy Equinox,Check engine light P0017, Service Stabilitrak comes on and the car loses power. Tried checking the EGR to ensure not stuck open and have had no improvement.

DTC P0017: Crankshaft Position (CKP) - Exhaust Camshaft Position (CMP) Correlation Bank 1
Which engine does yours have 3.4 or 2.8 , 3.0 , 3.2 , or 3.6 L Chevy Colorado P0017 Case Study Part 1

Dec 15, 2016 | 2010 Chevrolet Equinox

1 Answer

Replace camshaft postion actuator solenoid 2006 chevy impala

Have any codes ? Chevy Colorado P0017 Case Study Part 1 Doesn't matter if this is a Colorado . Same on impala VVT - variable valve timing .

Jul 02, 2016 | 2006 Chevrolet Chevrolet Impala LT

1 Answer

Code P0017 on engine

Trouble Code: P0017

Crankshaft Position (CKP)-Exhaust Camshaft Position (CMP) Correlation

Possible Causes:

Important: The scan tool control of the CMP actuator solenoid is inhibited when DTC P0017 sets. The following conditions may cause this DTC to set:

An improperly torqued crankshaft balancer.A mis-built or mis-timed engine.A loose or missing crankshaft balancer bolt.The CMP actuator solenoid stuck open.The CMP actuator stuck in a position other than 0 degrees.

Jan 04, 2013 | 2006 Chevrolet Colorado

1 Answer

My GMC canyon truck 2006 is running very rough. I did a diagnostic test at the part store, and the codes P0300, P0017, P0068, came up. The dash control panel says reduced power.

Code 300 is for a random miss, code 17 is for a problem with the timing between the cam and crank sensors, and code 68 is a problem between where the throttle position sensor is and the amount of air coming into the throttle body.
You may need to research the trouble codes to get the testing procedures. You may also need a scanner to do the tests.

Sep 15, 2012 | 2006 GMC Canyon

1 Answer

Im getting a P0017, P0014, P0300 code on my 06' Colorado, I replaced crankshaft sensor and camshaft sensor do I have to reset the timing on my vehicle?

po300 is a general missfire code if i rember right. there is more than likely an install procedure that will require you to clear all cods ( even if there is no code preasent ) before you install the new part or failure of those parts can happen

May 13, 2011 | 2006 Chevrolet Colorado

1 Answer

My 2006 chevy colorado with a manual transmission has been running rough and the engine light comes on and off. When im going through my gears it vibirates and acts like it doesn't really want to go and it...

Hello: If the engine light is coming on the you need to get the code read to determine what is causing the light to come on. With the code information you can diagnsis the problem. Auto Zone , Advance Auto can read the code and tell you and they probably not charge you.

Jan 21, 2011 | 2006 Chevrolet Colorado

1 Answer

Security light comes on Chevy Colorado still starts but

honestly, any number of thing's could cause the security light to come on, i would go to my local auto store and ask them to run a coad scsnner to find the problem, good luck

Dec 21, 2009 | 2005 Chevrolet Colorado

2 Answers

Rough idle

I had the same exact problem on my 2004 Colorado (3.5L). Cleaned the MAF sensor (with MAF sensor cleaner) and throttle body/plate - cleared it right up.

May 10, 2009 | 2006 Chevrolet Colorado

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

455 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides