Question about 1999 Plymouth Grand Voyager

1 Answer

99 Plymouth Voyager Rear Bumper

I need to remove the rear bumper on my 99 voyager. How would i go about doing that? Is it fairly simple

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 6,674 Answers

If you look up from under you should see some push clips. if your removing entire bumper with rebar & all, it's probably about 4 nuts holding it to bumper shocks, but be sure to look near ends at fenders for push clips , and or screws, and across mid section. watch it, it's pretty heavy with the rebar attached so make sure you have everything ready & remove nuts last, with some help to hold it up.

Posted on Feb 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove the rear bumper?


You didn't say what kind of car or truck that you have. Most are put on with screws and plastic bolts some of them hook together where the bumper and rear corner panel meet. You just need to look around under to see the set up. Some have screws under the trunk deck. So check there as well. Good luck. By the way if any plastic screws are broke you can buy them at most auto parts stores

Apr 26, 2014 | Cars & Trucks

1 Answer

How do I replace a headlight on 99 Honda Accord EX


fairly straight forward, but it does require removing the front bumper portion.blackjakjunk_11.jpgblackjakjunk_10.jpgblackjakjunk_9.jpgblackjakjunk_8.jpgblackjakjunk_7.jpg

Jun 20, 2011 | 1999 Honda Accord

1 Answer

Replace license plate light


open trunk and remove upholstery pins holding carpet to trunk lid, just the ones closest to the bumper-you don't need to remove the whole carpet, just pull it down. There are 9 screws that must be removed which allows you to remove the entire rear light panel. Once you have removed the rear panel and set aside you will be able to access the 2 bulbs. It's fairly simple and will save you about $100 by doing it yourself.

Jan 14, 2011 | 2001 Buick Park Avenue

1 Answer

How do I change the bumper on a 2000 Blazer


Front or rear, I am guessing it is the rear as they tend to get the most abuse and or rust! Start by removing the plastic step guard on the top of the bumper (use a flat ply bar) you will see the four bolts (remove those) and directly inline with those from the underside you will see four more (remove those) your bumper is free, there is one wire connector to release (licence plate lights) and simple lift off the bumper.

Dec 08, 2010 | 2000 Chevrolet Blazer

1 Answer

How do i [ut my rear bumper on my mustang its a 99


I am assuming you mean the rear fascia... this is the plastic part seen when outside the vehicle that covers the actual bumper

real simple to replace, about 6 screws and 2 bolts and the whole thing comes off

just make sure you pull it rearwards from the vehicle and DO NOT try to spread it away from the car

there are two very important clips in the rear quarter panel that the fascia mounts into

Mar 18, 2010 | 1999 Ford Mustang Cobra

2 Answers

How do you remove pass rear wheel bearing on 99 ply grand voyager


the bearing has 4 bolts holding it on the inner side facing the axle. remove the wheel and brakes to get access to it

Mar 07, 2010 | 1999 Plymouth Voyager

1 Answer

I need to change the fuel pump on a 99 jeep grand cheorkee having trouble removing plastic bumper fairing so i can remove the hitch which is under the tank cover


Try removing the hitch first if it's a factory hitch. There should be three nuts on either side.

Check tor two 8mm screws inside the rear wheel well bolting the bumper to the quarter panel where they meet on the side. There might be a clip under each tail light.Then remove the plastic clips and slide it straight back.

Feb 28, 2010 | 1999 Jeep Grand Cherokee

1 Answer

I need a new rear bumper for my 2002 chevy monte carlo. what all do i need besides the rear bumper cover? is this expensive? where do i buy them for cheap?


you will need the bumper and the mounting bolts. A junk yard will be your best bet for cheap. look in the yellow pages and start calling around until you find a good shop that does the work for a fair price.

Sep 12, 2009 | 2002 Chevrolet Monte Carlo

1 Answer

Cadi CTS 05 Front Blinker / Running Light Bulb is out


It is fairly simple to replace the turn signals on the CTS. You do not have to remove the whole bumper, just enough to let you inside behind the lights. Turn the steering wheels one way and remove the 4 clips around the bumper with a flathead screw driver. Then do it again to the other side. You can remove the top clips to give you more wiggle room. Look under the car and remove enough of the clips to loosen the sides. At this point you can stick in your hand from the wheel well and replace the lights. Just turn and pull and re-install the new lights. Simple.

Apr 12, 2009 | 2005 Cadillac CTS

1 Answer

Rear bumper on mazda mpv


Removal of the rear bumper on an Mazda 2004 to 2006 MPV.
It's afairly simple task: 1) Open the rear hatch or (door) remove the torx screws at the bottom of the weather strip. 2) Remove both tail lights by unscrewing the two phillip screws on each light, once removed the lights pulling toward the side of the van. Let them hang from the wires. You will see a clip (white in color),pry it out from behind the bumper material and go to the next step. 3) Remove three 8mm head screws in each fender well and three plastic clips. Then remove an 8mm screw at the top corner of the bumper against the rear fender. If your car has splash guards remove them as well. 4) Remove the two clips at the bottom of the bumper attached to the under carriage. 5) Pull the bumper toward the back of the vehicle be careful with the tail lights. Remember, they are hanging loose.
And that's it, you have done it.
Ferni

Oct 07, 2008 | 2005 Mazda MPV

Not finding what you are looking for?
1999 Plymouth Grand Voyager Logo

Related Topics:

252 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

69199 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...