Question about 1995 Honda Odyssey

1 Answer

My honda oddessey 1995, my engine crank but will not start and no spark in the spark plug, check fuel system no problem, replace already the distributor cap,rotor,ignition coil,spark plug, spark wires. still wont start

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 8,274 Answers

Hi, since you've replaced everything else, about the only thing left is the crankshaft position sensor. This is the sensor the computer uses to time the spark signals. Because this sensor is expensive, I recommend you test it first to verify it's bad before replacing. I have pasted test procedures below as well as replacement procedure in case it fails the tests. You will need an ohmmeter for the test. If you don't have an ohmmeter, you can buy one for as little as $10, or maybe you can borrow one. You will also need a timing light if you replace the sensor. Please let me know if you have questions, and thanks for using FixYa.


TESTING CRV and 1995 Odyssey Models

  1. With the ignition switch OFF , detach the electrical connector on the side of the distributor housing.
  2. Measure the resistance between the following two CKP wires:

    CRV models: The blue and white wires. The resistance should be 300-700 ohms. 1995 Odyssey models: The blue/green and blue/yellow wires. The resistance should be 700-1,300 ohms.
  3. If the resistance is not in the specified range, replace the distributor ignition housing.


REMOVAL & INSTALLATION CRV and 1995 Odyssey Models

  1. Remove the negative battery cable.
  2. Remove the distributor cap leaving the wires attached and place aside.
  3. Disconnect the electrical connectors at the side of the distributor housing.
  4. Make a matchmark reference mark between the distributor housing and the cylinder head and remove the distributor housing assembly.

To install:
  1. Transfer the components not supplied with the replacement distributor housing assembly.
  2. Install the distributor housing assembly in the reverse order of removal.

my honda oddessey 1995, my - jturcotte_1430.gif

Fig. Fig. 2: The Crankshaft Position (CKP) Sensor rotor looks like a small gear in the lower distributor housing- CRV and 1995 Odyssey models



7. Check and reset the ignition timing as outlined below.

ADJUSTMENT CRV and 4-Cylinder Odyssey Models



If equipped with an automatic transaxle, place the shifter in Park or Neutral. If equipped with a manual transaxle place the shifter in Neutral. Make sure to apply the parking brake and block the drive wheels.


  1. With the heater off and in the full cold position, start the engine and hold the engine speed at 3000 rpm, until the radiator fan comes on at least one time. To check the ignition timing, the engine must be at idle speed and at normal operating temperature. Make sure all electrical consumers (defroster, radio, air conditioning, lights, etc.,) are turned OFF.
  2. Locate the blue plastic Service Check (SCS) Connector, as follows:

    Odyssey models with 4-cylinder engines: centrally located on the passenger side, under the dash. The connector has two wires; one is brown with a black tracer, and the other wire is red.

See Figures 1 and 2

jturcotte_393.jpg

Fig. Fig. 1: The inductive lead of the timing light is placed around the No. 1 spark plug wire; and the light is aimed toward the marks on the crankshaft pulley.


jturcotte_1431.gif

Fig. Fig. 2: The red ignition timing mark on the crankshaft pulley is lined up with the pointer. The two small notches on either side of the red colored notch represent the plus (+) or minus (-) 2° increments. The white notch to the far right is Top Dead Center (TDC)

  1. Connect the SCS service connector tool number 07PAZ-0010100 or equivalent to the service connector. A paper clip can be substituted for the tool by forming a "U" shaped bend in the paper clip and carefully inserting it into the back side of the SCS service connector terminals. The purpose of the tool is simply to connect the two wires together temporarily.
  2. Connect a timing light to No. 1 ignition wire and point the light toward the pointer on the timing belt cover.
  3. Check the idle speed and adjust if necessary.
  4. The red mark on the crankshaft pulley should be aligned with the pointer on the timing belt cover.
The white mark on the crank pulley is Top Dead Center (TDC).
  1. Adjust the ignition timing by loosening the distributor mounting bolts and rotating the distributor housing to adjust the timing. Set as follows:
    2.2L/2.3L Odyssey 2.2L models: 13-17° at 650-750 rpm
  2. Tighten the distributor bolts to 17 ft. lbs. (24 Nm) and recheck the timing.
  3. Remove the SCS service connector or the substituted paper clip from the SCS service plug.

Posted on Apr 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 honda odissey cranks but wont start


To clarify, the check engine light should stay on until the engine starts.
Someone will need to figure out if you are lacking spark to the plugs, fuel to the injectors, or compression to proceed.

Dec 20, 2012 | Cars & Trucks

1 Answer

My 95 honda oddessey wont start. was driving and engine shut down. Replaced the distributor with the coil and iginter, because i had no spark now i still have no spark


Check the ignition switch, they are known to go bad. Two 6mm screws on the back side of the lock cylinder hold it in place. If it is original it is more than likely bad. Here is a link that was extremely helpful to me in resolving my no-start condition:
http://www.tegger.com/hondafaq/startproblems.html#ignitionswitch

Aug 05, 2011 | 1995 Honda Odyssey

1 Answer

2005 honda element won't idle


COULD BE STOPPED UP FUEL FILTER.CHECK FUEL PRESSURE SHOULD BE 48 PSI. IF LOWER HONDA ADVISE TO REPLACE FUEL FILTER.YOU HAVE TO REMOVE FUEL PUMP THROUGH ACCESS PANEL FROM THE FLOOR.IF FUEL PRESSURE OKAY.REPLACE AIR FILTER.REPLACE SPARK PLUGS IF YOU HAVE OVER 110000 MILES ON THEM.IF SPARK PLUGS BEEN CHANGED ALREADY.IF ENGINE STILL WONT CRANK AND IDLE.CODE SCAN FOR A FAULTY IDLE AIR CONTROL VALVE.

May 12, 2011 | 2005 Honda Element

2 Answers

I have a 2003 civic Honda .engine cranking but wont start.Fuel and Ignition were check already no problem was found. Is it maybe because I have change the original alarm of my car to a new alarm? Do I need...


I would check your firing order, and all the stuff with the distributor, no loose connections and stuff, check the condition of all your plugs, make sure they are gapped correctly, check everything, maybe your injectors are clogged or broken? (unlikely but still check it out) then at last check for compression. All you need is fuel, spark and compression to fire. Check all cylinders to make sure they are ok on everything.

Get your tools (for removing a spark plug) ready. Try to start the engine, pumping the accelerator a little while you crank. Take a spark plug out. Is the spark plug wet with gas (smell fuel)? If so, you are getting fuel. Hook the spark plug you just took out up to the coil, lay it on the engine where it will be grounded to the metal. Get someone to crank the engine, and check for spark at the end of the plug. If there is a good spark, that eliminates another problem (don't crank the engine, or let it run too long with the plug out). If you have spark, and fuel, either the timing is way off (broken, slipped timing belt/chain), or you have no compression (internal engine).

Do you have a "Check Engine" light, or any other warning light on? Recently you make any work there or disconnected the battery? Are you thniking in Theft, Immobilizer or Passlock security alarm? Is this occurrs and the keys isn't work, its need to re-programmed, for this need to visit your Honda dealer.

Keep us updated.

Feb 08, 2011 | 2003 Honda Civic

1 Answer

Engine cranks will not start


There are many things that can cause this condition. First you must isolate which system is malfunctioning. Check for spark at the spark plugs to see if the ignition system is at fault. If the spark plugs have good spark, then you must check fuel pressure to see if the fuel delivery system is at fault. If you have good fuel pressure then you must check for injector pulse at the fuel injectors to see if the fuel injection system is at fault. If all of these things are ok. Then you must check the compression in all of the cylinders to see if an engine mechanical failure is causing the problem. Once the failing system is identified, then you can test that system to find out what is causing it to malfunction. Only after all this happens, can anyone tell you why your car won't start.

Jan 23, 2011 | 1995 Honda Odyssey

2 Answers

Volvo 850 2.0 1995 non starting already fitted new plugs leads cap roter arm cam and crank sencors good spark good fuel presure and no imobliser light on plugs all dry when turning over engine


try spraying some easy start into the air intake while someone operates the starter if it trys to start you have a fuel system fault have you checked fuel pressure at injector rail you need to do this using gauge and check against volvo spec if low it will never run if ok check feeds to injectors using multimeter if no feed check relevent fuses if ok using multimeter check continuety of injector wireing back to ecu if it did not try to start using easy start check timing belt is ok and engine has compression

Jan 02, 2010 | 1995 Volvo 850

2 Answers

1995 ford explorer doesn't start, crank & cam sensors replaced


Does you fuel pump delivers fuel. Is it there a spark.

Dec 29, 2009 | 1995 Ford Explorer

1 Answer

Car wont start i have a new battery, new spark plugs and wires


It need to have fuel and sparks to start.
Have you check to see if there is spark after all new parts?
If there is spark, then check if it has fuel.

To check spark, hold 1 spark plug touching engine chasis while cranking, if there is no spark then problem with the coils or ignition module.
To check fuel, after cranking several times but no firing, take out a spark plug to see if it wet.
If it is dry then no fuel. For this, problem could be following in order:
-Fuel filter
-Fuel pump
-Fuel pressure regulator
- Fuel injectors
- Fuel injector module.
Need to go through troubleshooting step by step before changing the parts to correct a problem. Good luck in finding a good mechanic to test before spending money in costly partts replacement.

Sep 23, 2009 | 1995 Honda Civic

2 Answers

95 Camaro Z-28 starts hard


Need to verify fuel pressure at the injector rail with the engine cranking and with the key on and engine off. Specification is 55 - 61psi. The pressure should build with one cycle of the key. If the pressure is slow to build up there may be a restriction in the system between the pump and fuel rail .
The system should hold pressure without leaking down. If it leaks down there is a problem. If all is good there Checking for a good blue spark at several plugs to verify the ignition system is working ok. A vacuum leak could also cause a hard start issue.
A bad pick up coil or weak crank sensor can cause hard start issues also.

Sep 01, 2009 | 1995 Chevrolet Camaro

Not finding what you are looking for?
1995 Honda Odyssey Logo

1,889 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...