Question about Ford F-100

1 Answer

Put in oil guage and volt guage and my fuel guage and temp guage stop working.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 638 Answers

It sounds like something is not wired up right, i would re check the wiring according to the directions you recieved when you purchased your gages, to make sure you have it hooked up correctly. hope that this has helped you.

Posted on Apr 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Chevy blazer troubleshooting


Check for a broken or bad ground strap from the engine to the firewall of the engine compartment. This may be causing the problem. Hope this helps

Dec 29, 2013 | Cars & Trucks

1 Answer

My 1984 Nissan bluebird trx has a dashboard which shows temp, oil pressure and, on the driver's side, fuel guage and charge and these gauges are incremental gauges, ie they rise in increments. the fuel...


if i remember correctly there is a resister in the dash board that will need replacing, this is on the power side for both the gauges. . it will need replacing. i think a company in the 90's did a upgrade for the dash board so if its the upgrade it will be on a board. the original was on the back strip. you just cut it out and solder new one in its place to the parts left, but don't solder for to long as it can ment the strip.

Jul 01, 2017 | Cars & Trucks

1 Answer

I just bought a 1988 chevy k/1500 4-wd truck. the temp guae volt meter oil pressure guage in the cluster all worked the rest did not. I found a replacement at a local scrap yard. now the temp volt and oil...


first we will start will the fuel gauge most likely you are correct chevys and 1995 and older jeep wranglers had this problem the sending units failed very commonly. you could have possibly gotton another bad cluster but most likely the speed sensor has worn out. it has a plastic gear being turned by a metal gear and is located near the tail of the transmission. hope this helps

Jan 30, 2011 | 1988 Chevrolet K1500

1 Answer

Gas guages messed up


volt meter, fuel gauge, oil pressure and coolant temp all share the same power and ground

the circuit you want to check is the yellow and white wire from the dash to the dual switch

Mar 21, 2010 | 1995 Ford F250

1 Answer

My 1995 Jeep Wrangler has a problem with the guages.All of them are not working properly.The fuel only goes to 1/2 but will drop pass that.The oil pressure goes all the way to 80+ I put a manual guage in...


I would check the output of you alternator first of all. When you turn everything on you should see around 14 volts instead of the 12 volts. There is probably a problem with the alternator or a wiring issue.

Jan 28, 2010 | 1995 Jeep Wrangler

2 Answers

All guages on console are not working, truck-GMC 2006 P/U


Factory defect. Take it back to the dealer. Had my entire instrument cluster replaced at 85K miles. Even though out of warranty, everything was free.

Dec 29, 2009 | 2006 GMC Sierra

1 Answer

Had a slow coolant leak Oil temp guage redlined installed new failsafe thermostat, it still would not produce heat. Had a radiator flush and oil change and used bards leak, seems to have worked. Oiland...


there is a valve in the hot line to the heater core, it may not be opening. or you might have to disconnect the heater hoses and flush the heater core, stop leak will some times stop up core since tubes are very small

Dec 17, 2009 | 1995 Buick Regal

1 Answer

Gas guage and water temp gauge do not work clock works alt works oil works guages work just not gas and water temp ?????


On the rear of the instrument cluster there should be a resistor. This is how the fuel and temp guages are limited to a certain voltage decreasing the power to them so that they dont burn out. These (voltage limiters) resistors are available seperately from the dealership.

Oct 04, 2009 | 1987 Jeep Wrangler

1 Answer

Turn signal, tachometer, fuel and temp guage stopped working


you should pull out the gauge cluster and check the connector on the back side of the cluster.. i bet that is the issue

Jul 18, 2009 | 1989 Honda Accord 4 Door

1 Answer

Temp guage read hot, volt guage reads low, and oil pressure guage tops out. Could this be a bad ground?


Possibly, i would check the sending unit and of course the wires that connect to the temp prob. They often become worn or even short out on other wires. I suspect that the gage is telling the truth and you have a blown head gasket. Check the oil for water. Check the water level and see if you are losing water. good luck

Jun 03, 2009 | 1996 Ford Thunderbird LX

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...