Question about 2003 Ford Focus

1 Answer

How to fix drive belt of ford focus having no tentioner ?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

TENSIONER LOOK LIKE A PULLEY IT SELF, LOOK FOR PULLEY WITH A CENTER BOLT.THE TENSIONER PULLEY WILL BE BELOW ALTERNATOR ON THE 2.3 VINZ ENGINE AND TENSIONER PULLEY SHOULD BE NEXT TO WATER PUMP PULLEY ON THE 2.0 VIN3 ENGINE.YOU NEED A WRENCH TURN TENSIONER CENTER BOLT COUNTERCLOCK WISE TO RELEASE BELT TENSION.

Posted on Apr 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What do I do if I can not see timing marks on the camgears of a 2000 Ford focus Dohc anyone


according to autodata belt replacement guide , there are no timing ,marks on the cam gears
it require special tools and a good knowledge of mechanics to do the job so I strongly recommend that you get a workshop manual before starting on the job
I could type it all for you but with only two fingers , I would be here until next week as the directions are involved and you will need diagrams to full understand the procedure
that is why I suggest a workshop manual
the procedure is not as you would expect as on other engine makes and need to carefully followed

Feb 07, 2016 | 2000 Ford Focus

1 Answer

How to remove the serpentine belt


depends on vehicle. but for most you just need a wrench to take tention off the tentioner and remove belt. it does help if you borrow a tentioner tool from local parts store.

Jul 17, 2015 | 2001 Ford Taurus

1 Answer

Do u need to put tensioner belt on just)- to remove a worn out serpentine belt for ford focus 2000--2.0 dohc sedan car?


if it was my car id replace both belt and tentioner because belt tentioners are proun to fail on these cars

Jun 14, 2015 | 2000 Ford Focus

1 Answer

How to remove tention pulley 2003 ford focus


take the bolts out of the mounting plate that hold it to the engine block you do not just change the pulley on them you have to change the whole thing the spring get weak and that is why the belts squeal

May 05, 2014 | Dodge Sprinter Cars & Trucks

1 Answer

Replace drive belt on 2004 Ford Taurus


ok with a smooth pulley use smooth side of belt with serrated pulley use serrated side of belt. The belt will seem too short at first but with some real muscle it can be pulled into place.
I never leave the tentioner for last because it is usually hard to get at.
leave the most convenient pulley for last the job goes smoother.
put the belt on the crankshaft first.
then go around in either direction. remember the smooth serrated rule and rout the belt. most likely the alternator will have a smooth pulley just before or after it.
good luck!!!

Mar 02, 2013 | 2004 Ford Taurus

1 Answer

How to change serpintine belt on 2003 ford focus 2.3 engine


Most vehicles have a belt routing diagram sticker under the hood. If you do not have one, make a drawing of how the belt goes on before removing the old one. There will be whats called a tentioner pulley. Usually you can use a ratchet and socket to loosen the tention. It is spring loaded so watch your fingers and slowly release pressure on your ratchet when you are ready. Remove the old belt and put the new one on.

Jan 29, 2011 | Ford Focus Cars & Trucks

1 Answer

How do I remove the fan belt from the 6.0 diesel-ford f350 truck


there should be a automatic tentioner the easist way to find it is grap your belt and push or pull it you should see the tentioner move now feel on the back side you should feel a square hole that a half inch drive ratchet will fit in

Jan 22, 2010 | 2003 Ford F350 Super Duty DRW SuperCab

Not finding what you are looking for?
2003 Ford Focus Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...