Question about 2000 Cadillac DeVille

1 Answer

After plugging in the codekey device it read P0301 Standard DTCs (ISO 15031-6/SAE J2012) Cylinder 1 misfire detected. I changed out the coil but to no avail. What should I do?

Posted by on

1 Answer

Take to a repair shop

Beyond your expertise

Posted on Apr 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code po670 what does it mean


- P0670 states there is a problem with the glow plug control module or glow plug(s)
- P0670 Glow Plug Mod Control Circuit
- Standard DTCs (ISO 15031-6/SAE J2012): Glow Plug Control Module Control Circuit/Open

Read more: http://mbworld.org/forums/diesel-forum/485795-2008-gl320-cdi-cel-p0670.html#ixzz33DhzVypf

May 30, 2014 | 2008 Mercedes-Benz Mercedes Benz Ml Class

1 Answer

Po316, po 300, po301, po305 2004 ford freestar


These codes are making me lean towards the ignition coil pack.My stepson's 2001 Sable 3.0 v6 had one cylinder misfiring(5-code P0305),which shares a coil with cylinder 1(code P0301).I diagnosed it by trading wire 1 and 5 at the coil,and the code changed to P0301.You have codes for the two cylinders on the same coil,so this is most likely it.(these codes would also trigger P0300(Multiple Misfires Detected) and P0316(Misfire Detected First 1000 Revs)).

Oct 14, 2012 | 2004 Ford Freestar

2 Answers

Flashing SES, P0305, and P1145


A flashing SES light means that you are operating the vehicle under conditions that are DESTROYING your catalytic converters! This is not good.

Diagnostic Test Code (DTC) P0305 is defined by SAE J2012 as "Cylinder 5 Misfire Detected".

DTC P1145 is a "manufacturer-specific code" and is defined by Nissan as "Bank 2 Intake Valve Timing Control Position Sensor - High Or Low Voltage"

So, to put it simply, you need to find out WHY cylinder #5 is misfiring and get it fixed. You also need to diagnose the intake valve timing control position sensor circuits on bank 2 to (1) find out if the voltage is HIGHER or LOWER than specification (since the code itself is not specific about which it is). And (2) find out what is CAUSING the voltage to be out of specification and take the appropriate action correct it.

Apr 27, 2012 | 2002 Nissan Pathfinder

2 Answers

What do I need done if codes p0171 p0174 p0301 p0305 p0316 is it major problems


OK, We'll cover the Diagnostic Test Codes (DTCs), starting with the standard definition set by SAE J2012 (Revised December 2007)
DTC P0171 "System Too Lean Bank 1"
DTC P0174 "System Too Lean Bank 2"
DTC P0301 "Cylinder 1 Misfire Detected"
DTC P0305 "Cylinder 5 Misfire Detected"
DTC P0316 "Engine Misfire Detected on Startup (First 1000 Revolutions)"

The "system lean" codes are pretty much telling you that there is way too much oxygen in the exhaust. There is too much oxygen on BOTH sides of the engine, and that is why you are getting codes for bank 1 and for bank 2. Bank 1 is the side where #1 cykinder is located and Bank 2 is the opposite side.

The misfire codes are pretty self-explanatory. #1 and # 5 cylinders are misfiring. The P0316 DTC is telling you that the misfire monitor is detecting a misfire as soon as the engine starts. This tells you that it is a very severe misfire and that the engine does not have to warm up and the car does not have to be driven to detect the misfire.

A misfire can be caused by many things it can be vacuum leaks, bad spark plugs, bad ignition cables, faulty ignition coils, fouled or malfunctioning injectors or injector circuits, blown head gasket, cracked cylinder head, burnt valves, etc.. etc..

However, look at the codes you have. Then look at the firing order for your engine. 2002 Mercury Sable is only equipped with a 3.0L 2V 6-cylinder engine.
The firing order is 1-4-2-5-3-6

Now if you take the firing order and split it in half, stack the two halves on top of each other, it looks like this:
1-4-2
5-3-6

When you look at the firing order this way, you can see that cylinders 1 an 5, 4 and 3, and 2 and 6, are "PAIRED" cylinders. They are exacly opposite in the firing order. Now, the cylinder only fires every second revolution of the crankshaft. With paired cylinders, one of the cylinders in the pair will fire on the first revolution and the other cylinder will fire on the second revolution.

Looking back at your codes, please note that the cylinders that are setting the misfire codes are paired cylinders.

Now the coil pack for your ignition is actually made up of three coils. Each coil fires a set of paired cylinders. If you look at the top of the coil, it will usually be marked with the cylinder numbers that each coil tower is supposed to connect to. The coil will look just like the firing order split and stacked as above.

With all of this said, I would say that it is VERY LIKELY that your misfire codes are being caused by a defective ignition coil.

The lean codes are a little different.

These are USUALLY caused by vacuum leaks which allow too much air into the engine that is not getting measured by the Mass Airflow (MAF) sensor and causes the engine to be getting too much air and not enough fuel (running lean).

I would take a good look at all of the vacuum hoses and lines. Ford is notorious for getting holes in the rubber parts that connect the PCV tubes.

If you do not find any obvious reasons for a vacuum leak, then you may want to fix the misfire codes, reset the computer memory, and drive the vehicle to see if the lean codes come back again. The misfires COULD be the cause of the lean codes. In a perfect world, this is not supposed to happen because the misfire monitors setting codes will not allow the oxygen sensor monitors to run and set lean codes. However, I HAVE seen cylinder misfires that have caused lean codes.

I hope this helps you to figure it out. Good luck!

Feb 03, 2012 | 2002 Mercury Sable

1 Answer

Code p1313 p1316 p1111 p0301 means what?


Odd one this to have P1111 as well.

According to my data P1111 is all dtc checks compleated, http://www.bluejag.co.uk however some websites show it as a Intake Air Temperature (IAT) Sensor Circuit Intermittent High Voltage, I'm fairly sure that the latter is incorrect.

check the basics first plugs, leads, corroded ground connections etc then its a bit of a guessing game


As for the other codes

P0301 = Misfire detected - cylinder 1
P1313 = Misfire rate catalyst damage - bank 1
P1316 = Misfire excess emission


Possible causes (as per JTIS):

Cylinder compression low
Worn camshaft / broken valve spring(s)
Fuel delivery pressure (low / high)
Fuel injector(s) restricted / leaking
Fuel injector(s) continuously open
Fuel contamination
Fuel injector circuit fault(s)
(Injector DTCs also flagged)
Spark plug failure / fouled / incorrect gap
ECM to ignition coil primary circuit fault
(Cylinder misfire detected DTC also
flagged)
Ignition coil failure

hope this helps

Mar 13, 2011 | 2002 Jaguar X-Type

3 Answers

CODES-PO301-PO303-PO316- CHANGED PLUGS & WIRES. STILL MISS ON START UP, GOES AWAY MOST OF THE TIME ABOVE 1000 R.P.M


P0301 - Cylinder 1 Misfire Detected.

Causes:
- Improper spark plug at cylinder #1
- Insufficient compression at cylinder #1
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #1
- Fuel injector #1 may be faulty
- Intake air leak

Solutions:
- Perform Injector Service
- Replaced Spark Plug #1
- Replaced Injector #1
- Replaced Ignition Coil #1

P0303 - Cylinder 3 Misfire Detected.
Follow info from P0301.

P0316 - Misfire Occurred In The First 1,000 Engine Revolutions.

Causes:
- Damaged CKP sensor.
- Ignition System.
- Fuel Injectors
- Running out of fuel
- Fuel Quality
- Base engine
- Damaged Powertrain Control Module

Solutions:
Usually the P0316 is combine with a P03XX codes. The P03XX code indicates in which cylinder the misfire occurred.

Jan 17, 2011 | 2002 Mercury Sable

1 Answer

2003 mercedes Benz C240 codes P0300, P0301, P0302 and P0303. Please, help me how to fix?.


P0300 Random Misfire Detected
P0301 Cylinder 1 Misfire Detected
P0302 Cylinder 2 Misfire Detected
P0303 Cylinder 3 Misfire Detected
according to this fault codes first mark ignition coils
3 ---------------- 6
2 ---------------- 5
1 ---------------- 4
RB-------------LB
this right banks and left bank, please remove Ignition coils with lids and spark plugs from right bank and swap with left bank, if fault code change as
P 0304 Cylinder 4 Misfire Detected
P 0305 Cylinder 5 Misfire Detected
P 0306 Cylinder 6 Misfire Detected
You can Identify it's a faulty ignition system then next swap ignition lids from ignition coils be careful each coils have two lids one short and other long bit deference and when you remove and fix it to the car keep in mind correct order because each coil two different fire for two spark plugs don't mix up, if you mix it can create the fault code.if you detect any fault ignition coils or spark plugs or lids replace that and also whether god or bad recommend to replace spark plugs, find the right that's most important thing, if this way couldn't found the any ignition fault next step is check fuel presser, when the engine running fuel presser must be around 4.5 bar without engine running must be 4 to 6 bar if the fuel presser too low need to check two different things one is fuel pump other is fuel injectors, in this case you can swap injectors from right bank to left bank and find is the injectors leaking, if not leaking faulty fuel pump.is this information helped you? if yes please leave a comment,

Oct 15, 2010 | 2007 Mercedes-Benz C230 Sedan

2 Answers

Code p0301 and p0316


P0301 - Cylinder 1 Misfire Detected
P0316* - Engine misfire detected on Startup (First 1000 Revolutions) Could be a Bad Coil or bad spark plug or a bad wire on cylinder one. Check the plug and the wire first then move to the coil. Good Luck.

Sep 23, 2010 | 2002 Ford Explorer Sport Trac

4 Answers

HI I HAVE A 2001 MAZDA TRIBUTE AND THE CODES PO301 AND PO303 CAME UP IN THE DIAGNOSTIC REPORT. THE CAR TURNS OFF WHEN I WARM IT UP IN THE MORNING IN THE COLD AND AFTER THAT ITS FINE I ALREADY CHANGED THE...


cylinder 1 misfire and low compression. Plugs and wires changed plus new fuel injectors. The engines still misses and no one can find the cause. When put on the computer it read misfire cylinder 1.

Dec 31, 2008 | 2004 Mazda Tribute

Not finding what you are looking for?
2000 Cadillac DeVille Logo

217 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...