Question about 1998 Oldsmobile Silhouette

Open Question

1998 olds silhouette can`t get oil pan off ,have removed 12 oil pan bolts,still wont come off

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 51 Answers

SOURCE: oil pan removal on 2002 gmc sierra

did you pull the rubber plugs between the motor and trans out? there are either nuts or bolts up there

Posted on Mar 15, 2009

Molson02536
  • 3854 Answers

SOURCE: pontiac montana oil pan bolt diagram for removal

If all the bolts are off, then the gasket is holding the oil pan in place and your going to have to tap it with a mallet, Not a hammer but a mallet so you don not damage the oil pan. Good luck and hope this helps.

Posted on Jul 13, 2009

  • 171 Answers

SOURCE: timing chain tensioner worn; plastic parts are in eng oil pan

No, should have enough room to slide it out ,if not disconnect the engine mounts and jack up or lift up the engine just enough to slide the pan.

Posted on Nov 02, 2009

juncro
  • 467 Answers

SOURCE: My 1998 chevy s10 blazer 4x4 looks to be leaking

no special way, the oil gasket need to change

Posted on Nov 10, 2009

lilperrin
  • 6 Answers

SOURCE: How to remove the crossover exhaust pipe in oldsmobile silhouette

Dont Ask Me ******* ******* God **** **** **** ***

Posted on Jan 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 Silhouette. How do I remove the oil pan?


oil pan an be removed when engine out of the car and engine drained from oil, you have several bolts holding it on it must be 10 mm soc

Jul 13, 2015 | Oldsmobile Cars & Trucks

1 Answer

Oil Pan Gasket Replacement/ Oil Pan removal


yes the starter does have to be removed but also the engine mounts must be also as the engine must be raised about 10 " to get the pan out. if you do try this make sure you have very very sturdy jack stands for the engine to just a jack as the jack will lift it but wont maintain it long enough to safely remove the pan and reinstall it......good luck and be very carefull

Aug 11, 2014 | 1998 Oldsmobile Silhouette

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

1 Answer

How to remove oil pan


Drain the oil first. Then look up a round the edged for a series of about 12 bolt heads that go all the way a round the pan. Remove them and the pan well come down. Old gasket may have it stuck to motor so help it with a good bump. :)

Apr 14, 2014 | 1994 Nissan Pickup

1 Answer

I have a 2002 oldsmobile silhouette that has low EOP


For oil pump,oil pump pressure,oil warning light,oil low,oil ewplacing and other car engine oil problems,the help links are provided below.Click the link to go through the procedure :-----Oil light came on and the car died?http://schematicsdiagram.blogspot.in/2012/03/oil-light-came-on-and-car-died.html--------How to replace Oil filler cap or breather cap?http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-oil-filler-cap-or.html---------Oil pouring out from left front of engine?http://schematicsdiagram.blogspot.com/2012/01/oil-pouring-out-from-left-front-of.html------Common Causes of Car Oil Leaks?http://schematicsdiagram.blogspot.com/2011/12/common-causes-of-car-oil-leaks.html--------Troubleshoot Car Oil leak?http://schematicsdiagram.blogspot.com/2011/12/troubleshoot-car-oil-leak.html--------Oil change details?http://repairhelpcenter.blogspot.com/2012/01/toyota-highlander-sport-oil-change.html---------Low oil pressure light?
http://howtobyme.blogspot.com/2011/11/low-oil-pressure-light-on-dodge-magnum.html
----------
leaking oil from oil pan?
http://howtobyme.blogspot.com/2011/11/kia-sportage-leaking-oil-from-oil-pan.html ----------
Car Turns OFF due to low oil pressure warning light?

http://schematicsdiagram.blogspot.com/2011/12/car-turns-off-due-to-low-oil-pressure.html

------------
leaking oil from timing cover?

http://technoanswers.blogspot.in/2012/02/toyota-corolla-leaking-oil-from-timing.html

----------
For more oil and oil pump details check out the direct links below: ---

How to Replace Oil Pan on car?
http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-oil-pan-on-audi-a4-and.html
--------
How to Replace an Oil Pan Gasket?
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pan-gasket.html
-----------
HOW TO REPLACE AN OIL PUMP
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pump.html
----------
HOW TO CHANGE ENGINE OIL AND FILTER
http://schematicsdiagram.blogspot.com/2011/07/how-to-change-engine-oil-and-filter.html
----------
HOW TO REPLACE AN OIL PRESSURE SWITCH (SENSOR)
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-oil-pressure-switch.html
-----------
How to Check Differential Oil Leaks and Replace Oil
http://schematicsdiagram.blogspot.com/2011/07/how-to-check-differential-oil-leaks-and.html
----------
HOW TO PERFORM A BASIC ENGINE TUNE UP-OIL CHANGE
http://schematicsdiagram.blogspot.com/2011/08/how-to-perform-basic-engine-tune-up-oil.html

-------


Oil pan Gasket on car?
http://howtobyme.blogspot.com/2011/11/oil-pan-gasket-on-1998-toyota-tercel.html

---------

Oil pressure for car?

http://schematicsdiagram.blogspot.com/2011/12/oil-pressure-for-2001-gmc-jimmy-v6.html

----------
How to replace Oil Pan on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pan-on-2008-honda.html

---------
How to replace Oil Pressure Sensor on car?

http://schematicsdiagram.blogspot.com/2011/12/how-to-replace-oil-pressure-sensor-on.html

-----------
How to replace Oil Pump on car?

http://howtobyme.blogspot.com/2011/12/how-to-replace-oil-pump-on-2008-honda.html

----------
Car oil leak?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leak.html

----------
Car oil leaks from valve cover gasket?

http://schematicsdiagram.blogspot.com/2011/12/car-oil-leaks-from-valve-cover-gasket.html

----------
Oil light blinks on dashboard?

http://schematicsdiagram.blogspot.com/2011/12/oil-light-blinks-on-dashboard.html

-----------
Oil pressure issues on car?


http://repairhelpcenter.blogspot.com/2012/01/oil-pressure-issuers-on-toyota-tundra.html

-----------
Oil leaks from air filter on ford?

http://technoanswers.blogspot.com/2012/01/oil-leaks-from-air-filter-on-ford.html

---------
Wire running from oil pan to alternator?

http://technoanswers.blogspot.in/2012/02/wire-running-from-oil-pan-to-alternator.html

--------------
Why car leaks oil from oil filter?

http://schematicsdiagram.blogspot.in/2012/02/toyota-camry-leaks-oil-from-oil-filter.html

------------
Why engine is consuming lots of oil?

http://schematicsdiagram.blogspot.in/2012/02/2008-scion-xb-24l-engine-is-consuming.html

-----------
Maint REQD message on car dash?

http://schematicsdiagram.blogspot.in/2012/02/maint-reqd-message-on-2008-lexus-rx350.html

------
Remove Sump oil pan?

http://repairhelpcenter.blogspot.in/2012/03/remove-volkswagen-sump-oil-pan.html

--------
Sump not coming OFF?

http://repairhelpcenter.blogspot.in/2012/03/sump-not-coming-off.html

-----------
How to remove the sump on car?http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-sump-on-vw-beetle.html----------Car oil sump removal diagram?

http://repairhelpcenter.blogspot.in/2012/03/volkswagen-beetle-oil-sump-removal.html

---------

This will help.

Thanks.

Feb 02, 2012 | 2002 Oldsmobile Silhouette

1 Answer

Where is the oil pump located on a 1999 ford taurus and whats items do i need replace a long with the oil pump


Remove oil pan oil pump and pick up tube & screen will be bolted on.
You should get oil pump lube, carb. cleaner, new pump oil,
oil pan gasket, silicon, oil & filter, loc-tight, gasket remover & tools metric, 1/4 drive socket set, scraper / putty knife, 2 jack stands, a jack or ramps,
& blocks for rear wheels.
Lets get started.

(1)Get your car up on stands or ramps block rear tires.

(2)Drain oil & remove oil filter remove battery cable NEG (-)

(3)remove pan

(4)remove old pump

(5)remove pick up tube from oil pump

(6)Now clean tube & screen with carb. cleaner place on news paper to dry.

(7) clean all old gasket off from engine & pan also clean bolts

(8)place silicon on pan place gasket on pan put bolts in from gasket side to Aline holes put a side to dry

(9) Attach tube to pump with a little loc-tight fill pump with oil pump lube

(10)attach pump to engine block make sure rod goes in proper & bolt are tight.

(11)Bolt pan back on engine using a 1/4 in drive ratchet don't over tighten bolts get all bolts in now slow run each bolt in starting at 1 end then jump to the other then go to bolt at other end a cross from 1st bolt. Do this till all bolts are ran in. Now tighten bolts look for gasket on side of pan.If it starts to push out stop go to next bolt.

(12)Instill new filter & drain plug,& pour in oil

(13)Replace Neg - cable

I hope this works for you it's a basic oil pump change for most cars.
Some take more steps.

Jul 14, 2010 | 1999 Ford Taurus

2 Answers

How can i remove the oil pan gasket?


REMOVAL & INSTALLATION

The radio may contain a coded theft protection circuit. Always obtain the code number before disconnecting the battery.
2.2L, 2.3L and 2.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Drain the engine oil into a sealable container.
  4. Install the drain bolt with a new gasket. Tighten the bolt to 33 ft. lbs. (44 Nm).
  5. Remove the front wheels and the splash shield.
  6. Remove the center beam.
5dbe5cd.jpg

Fig. To gain access to the oil pan, remove the center beam-2.2L and 2.3L engines
  1. Detach the Oxygen sensor (O 2 S) electrical connector.
  2. Remove the bolts from the support bracket on the exhaust pipe.
  3. Remove the nuts attaching the exhaust pipe to the exhaust manifold and the catalytic converter.
  4. Remove the exhaust pipe and discard the gaskets.
  5. If equipped with an automatic transaxle, remove the converter cover.
  6. If equipped with a manual transaxle, remove the clutch cover.
  7. Remove the oil pan nuts and bolts (in a criss-cross pattern) and the oil pan; if necessary, use a mallet to tap the corners of the oil pan. DO NOT pry on the pan to get it loose.
  8. Clean the oil pan mounting surface of old gasket material and engine oil.
To install:
  1. Install a new oil pan gasket to the oil pan. Apply liquid gasket to the corners of the curved section of the gasket.
  2. Install the oil pan to the engine.
  3. Install the oil pan nuts and bolts and tighten the nuts and bolts in sequence. Tighten the nuts and bolts in 2 steps to 10 ft. lbs. (14 Nm).
  4. If equipped with an automatic transaxle, install the torque converter cover. Tighten the bolts to 108 inch lbs. (12 Nm).
  5. If equipped with a manual transaxle, install the clutch cover. Tighten the bolts to 108 inch lbs. (12 Nm).
  6. Install the exhaust pipe with new gaskets and new locknuts. Tighten the nuts attaching the exhaust pipe to the manifold to 40 ft. lbs. (54 Nm)and tighten the nuts attaching the exhaust pipe to the catalytic converter to 25 ft. lbs. (33 Nm). Install the bolts to the exhaust pipe support bracket and tighten the bolts to 13 ft. lbs. (18 Nm).
  7. Attach the Oxygen sensor (O 2 S) electrical connector.
  8. Install the center beam and tighten the mounting bolts as follows:

    Prelude: 43 ft. lbs. (60 Nm) Accord: 37 ft. lbs. (50 Nm)
  9. Install the splash shield and tighten the mounting bolts to 84 inch lbs. (10 Nm).
  10. Install the front wheels.
  11. Lower the vehicle and fill the engine with oil.
  12. Connect the negative battery cable and enter the radio security code.
  13. Start the engine and check for leaks.

039a698.jpg

Fig. Oil pan mounting bolt tightening sequence-2.2L and 2.3L engines

402f99d.jpg

Fig. Oil pan tightening sequence-2.7L engines


3.0L Engine

fc8e34b.jpg

Fig. Tighten the oil pan bolts in three steps, in sequence, to 8.7 ft. lbs. (12 Nm)

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the engine undercover.
  4. Drain the engine oil and replace the drain plug.
  5. Remove the front exhaust pipe.
  6. Remove the oil pan mounting bolts.
  7. Hammer a seal cutter between the engine block and oil pan to break the seal.
  8. Remove the oil pan.
To install:
  1. Clean the oil pan flange and engine block mounting surface.
  2. Apply sealant to the oil pan flange. Be sure to apply sealant toward the inside of the bolt holes.
  3. Install the oil pan on the engine. Tighten the bolts in sequence to 8.7 ft. lbs. (12 Nm).
  4. Install the exhaust pipe.
  5. Install the undercover.
  6. Lower the vehicle.
WARNING Operating the engine without the proper amount and type of engine oil will result in severe engine damage.
  1. Refill the engine with the correct amount of oil.
  2. Connect the negative battery cable.
  3. Start the engine and check for leaks.

I really hope help you with this (remember rated this help) Good luck.

Sep 23, 2009 | 1996 Honda Accord

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

1 Answer

How to remove oil pan from 2003 kia spectra


REMOVAL

1. Disconnect negative battery cable.
2. Drain engine oil
3. Remove LH and RH side splash shields.
4. Remove front exhaust pipe.
5. Remove oil pan mounting bolts.
  1. Remove oil pan with screwdriver or suitable tool as shown in figure. Caution:
a) Do not force tools between cylinder block and oil pan because this may damage sealing surfaces. b) Do not damage sealing surfaces when removing old sealant

  1. Remove oil strainer.

Replacement

Caution:
a) If oil pan is reused, remove all foreign material from sealing surfaces of cylinder block and oil pan. b) If bolts are reused, remove old sealant from bolt threads.


  1. Install oil strainer. Tightening torque: 5.8 - 8.7 ft. lbs. (7.8 - 11.8 Nm, 0.8 - 1.2 kg-m)
  2. Apply a continuous bead of silicone sealant to baffle plate along inside of bolt holes on contact surfaces. Caution: The oil pan must be installed no longer than 5 minutes after silicone sealant is applied.
3. Install oil pan. Tightening torque: (A) (B) (C) (D): 5.8 - 8.0 ft. lbs. (7.8 - 10.8 Nm, 0.8 - 1.1 kg-m) (E): 28 - 38 ft. lbs. (38 - 51 Nm, 3.8 - 5.3 kg-m)

4. install front exhaust pipe. Tightening torque: (A): 29.7 - 40.5 ft. lbs. (40.2 - 54.9 Nm, 4.1 - 5.6 kg-m) (B): 51 - 69 ft. lbs. (69 - 94 Nm, 6.9 - 9.4 kg-m) (C): 15.2 - 20.2 ft. lbs. (20.6 - 27.4 Nm, 2.1 - 2.8 kg-m)

5. Install LH and RH side splash shields. Tightening torque: 12 - 18 ft. lbs. (16 - 24 Nm, 1.6 - 2.4 kg-m)
6 . Fill with specified amount and type of engine oil.

GOOD LUCK,I HOPE THIS HELPS...

Jun 04, 2009 | 2003 Kia Spectra

1 Answer

Oil pump replacement


This MAY seem Strange But It IS ALL necessary for Oil Pump Replacement. And Please Don't Forget to Rate Me as Most Folks Do Not. Thank You and GOOD LUCK with the Oil Pump Job Also


OIL PUMP
It is necessary to remove the oil pan, oil pickup and chain case cover to service the oil pump rotors. The oil pump pressure relief valve can be serviced by removing the oil pan and oil pickup tube. Refer to Timing Chain Cover Removal and Installation for procedures.

DISASSEMBLY
  1. To remove the relief valve, proceed as follows:
  2. Drill a 3.175 mm (1/8 inch) hole into the relief valve retainer cap and insert a self-threading sheet metal screw into cap.
  1. Clamp screw into a vise and while supporting chain case cover, remove cap by tapping chain case cover using a soft hammer. Discard retainer cap and remove spring and relief valve.
  2. Remove oil pump cover screws, and lift off cover.
  3. Remove pump rotors.
  1. Wash all parts in a suitable solvent and inspect carefully for damage or wear.
Oil Pump Assembly
  1. Assemble pump, using new parts as required. Install the inner rotor with chamfer facing the cast iron oil pump cover.
  2. Tighten cover screws to 12 Nm (105 inch lbs.).
  3. Prime oil pump before installation by filling rotor cavity with engine oil.
  4. Install chain case cover. Refer to Timing Chain Cover Installation.
REMOVAL of Timing cover
REMOVAL
  1. Disconnect negative cable from battery.
  2. Remove timing chain cover.
REMOVAL Of Oil Pan to gain Access to OIL PUMP
  1. Disconnect negative cable from battery and remove engine oil dipstick.
  2. Raise vehicle on hoist and drain engine oil.
  3. Remove bending brace to transaxle attaching bolt.
  4. Remove bolts attaching dust cover to transaxle housing. Lower dust cover to gain access to oil pan bolts.
  5. Remove oil pan screws and remove oil pan.
INSTALLATION
  1. Clean surfaces and apply a 1/8 inch bead of Mopar (R) Silicone Rubber Adhesive Sealant or equivalent, at the parting line of the chain case cover and the rear seal retainer.
    1. Use a new pan gasket.
    2. Install pan and tighten screws to 12 Nm (105 inch lbs.).
    3. Install dust shield and bending brace to transaxle housing.
    4. Lower vehicle and install oil dipstick.
    5. Connect negative cable to battery.
    6. Fill crankcase with oil to proper level.

Mar 27, 2009 | 1998 Chrysler Town & Country

Not finding what you are looking for?
1998 Oldsmobile Silhouette Logo

Related Topics:

75 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...