Question about Ford F-150

1 Answer

I need a diagram for my 1982 ford f50 2 wheel drive truck. (or it could be called a radius support arm) please help me.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 334 Answers

Hello littledouser,

I hope this helps.

i need a diagram for - netvan_61.png


Regards,
netvan

Posted on Apr 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front end shimmy. Shop says passenger side radial arm is bent and wheel will not free wheel. What is radial arm? Need diagram of parts associated.


First, the shop diagnosis sounds a bit strange, unless you are not understanding what you were told.
I have heard of a radius arm but likely I've called it by a different name (like the proper name for a driveshaft is a propeller shaft, but if you call it that no one will know what you're talking about) The part I fail to understand is that its preventing the wheel from freewheeling? Makes no sense.
I suggest that you either have them put the car in the air and physically show you what they are telling you, or have another shop take a look at it and see what they find.
Most front end shimmy I've seen is usually caused by bad ball joints or a bad bushing elsewhere in the suspension.

Jun 07, 2010 | 1996 Jeep Grand Cherokee

1 Answer

I am trying to identify the name of the part that has broken


sounds like a rear radius arm has rotted off,you should be able to pick one up at a parts store or even a dealer,usually the dealer will have better luck getting the correct part and they can show you a diagram of the suspension and let you p[ick out the part you need,hope this helps

May 31, 2010 | 1995 Ford Escort

2 Answers

Steering is loose, lots of play in steering wheel


you need to do what i call a dry check i do before performing an alignment have someone sit in truck and shift steering wheel from side to side lightly while you look at steering components check for loose pitman arm,drag link if used inner tie rods outer tie rods or excessive play in steering box then jack up each front wheel and check upper and lower ball joints

Mar 18, 2010 | 1992 Ford Bronco

1 Answer

I'm looking for a front suspension diagram for a 1997 Ford Ranger 4wd. Can you point me in the right direction?


Suspension The independent front suspension (IFS) system is composed of a two-piece front driving axle, two front coil springs (5310) and two radius arms. The front driving axle consists of two independent axle arms. One end of each axle arm is anchored to the frame (5005). The other end of each axle arm is supported by the front coil springs and radius arm.

Front Suspension
f8852f9.gif

Mar 15, 2010 | 1997 Ford Ranger SuperCab

1 Answer

1995 e150 ford van,, 4.9 6cyl i need to replace the bushings on the radius arms. do i need to remove the springs or do the radius arms , just unbolt (front and the back) and remove? i appreciate your help....


Hi Darrell,
No the springs will remain in place,You will need new bolts and nuts before you start the job,they are 1/2 x one inch.you'll need five of them.unfortunately there are three large rivets you will need to torch off besides the other three bolts and nuts. Remove the radius arm nut and outer bushing before you loosen the arm.
good luck

Dec 29, 2009 | Ford E-150 Cars & Trucks

1 Answer

My 1996 taurus has a wobble with the front right wheel


the only rod i can think of is called a radius arm ....it goes from the front crossmember to the lower control arm

Mar 20, 2009 | 1996 Ford Taurus

1 Answer

1999 ford explorer pulls to right when put into 4 wheel drive


they have what are called Radius Arm Bushings.That cause this problem and other vibration problems also. Go to Explorer forum com site for info on how to replace the.

Feb 01, 2009 | 1999 Ford Explorer

1 Answer

Ford escort 14oo, 1997


big problems with bushes on radius arms,take vehicle to garage straight away,do not drive this vehicle you could kill someone

Dec 21, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...