Question about 1993 Plymouth Grand Voyager

1 Answer

Is the rear brake drum and hub on a 1993 Plymouth Voyager one piece or is it two pieces that can be separated? (not equipped with ABS)

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Plymouth Master
  • 5,763 Answers

This 1993 voyagers rear brake durms are two pieces, make sure there are no lock clips over the studs which i dont think there are on this 1993, these drums sometimes are tough to remove off the hub, spray wd 40 around the hub and take a hammer and hit drum in area where the studs are, no hit studs, you will need to turn and hit, hit it hard so it breaks free, you will see it break loose from hub,i have had some that i haf to remove the center hub nut and bearing to remove the drum, then with drum and hub off spindle i then removed the drum from hub, hope this helps.

Posted on Apr 03, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am unable to remove the rear brake drums on a 1996 Plymouth Voyager to inspect my brakes; what do I need to do so the drums will come off?


you have to remove the hub assembly, remove the center dust cap cotter pin and the holding nut, then pull the asssembly off

Aug 18, 2010 | 1996 Plymouth Voyager

1 Answer

Need to know the torque specs for a rear wheel bearing on a 1999 monte carlo?


Hub & Bearing 3.8L engine Removal & Installation To Remove:
Hub and bearing assembly mounting 88008g39.gif

All W-body cars are equipped with sealed hub and bearing assemblies. The hub and bearing assemblies are not serviceable. If the assembly is damaged, the complete unit must be replaced.
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle with jackstands.
  3. Remove the rear wheel and tire assembly.
  4. If equipped with rear disc brakes, remove the caliper, bracket and rotor.
  5. If equipped with rear drum brakes, remove the brake hose bracket and drum.
  6. If equipped, detach the ABS electrical harness.
  7. Unfasten the four hub/bearing-to-knuckle attaching bolts, then remove the hub/bearing assembly.
To Install:
  1. Install the hub/bearing assembly onto the knuckle. Install the four attaching bolts and tighten to 52 ft. lbs. (70 Nm).
  2. If equipped attach the ABS electrical harness.
  3. Install the rotor, caliper and bracket or drum and bracket, as applicable.
  4. Install the wheel and tire assembly.
  5. Carefully lower the vehicle.
  6. Connect the negative battery cable.

Jul 15, 2010 | 1999 Chevrolet Monte Carlo

1 Answer

How to replace a rear wheel bearing on voyager


this is a one piece part hub and bearing assy. even if auto parts sales you bearing separated highly recommend to replace whole unit

Nov 19, 2009 | 2000 Chrysler Grand Voyager

1 Answer

Trying to remove rear brake drum cover,have already adjusted star wheel and still won't remove. what am i doing wrong? for a 93 plymouth grand voyager


  1. Raise and support the rear of the vehicle on jackstands.
  2. Remove the wheels and tire assemblies.
  3. Remove the brake shoe adjusting slot cover from the rear of backing plate.
  4. Insert a thin tool through the adjusting slot and hold the adjusting lever away from the star wheel.
  5. Insert an adjusting tool and back off the star wheel by prying downward with the tool.
  6. Remove the center hub dust cover, nut, washer, brake drum, hub and wheel bearings.
To install:
  1. Inspect the brake lining and drum for wear.
  2. Inspect the wheel cylinder for leakage. Service as required.
  3. Remove, clean, inspect and repack the wheel bearings.
  4. Install the brake drum and tighten the hub nut to 20-25 ft. lbs. (27-34 Nm), then back off the nut until bearing pressure is released.
  5. Retighten the nut finger tight, align the cotter pin hole and install the cotter pin.
  6. Adjust the rear brakes as described in the beginning of this section.

36e0d00.gif
Removing the rear drum adjusting hole cover plug

Oct 07, 2009 | 1993 Plymouth Grand Voyager

1 Answer

ABS LIGHT AND BRAKE LIGHT COMES ON


please replace the rear brake shoes with brand new, not relined, purchased from the dealer. Also, replace all the rear brake hardware, springs, etc.

Jul 17, 2009 | 1993 Plymouth Voyager

1 Answer

Fixing brakes


Try bleading the brakes, sounds like you have in them. Than the ABS light should go out & you shouldn't have to worry about the fuses.

Jun 02, 2009 | 1993 Plymouth Voyager

1 Answer

1993 Plymouth voyager--brake light on no power assist


Either ur Abs brains  shot which r located below the battery or u have a vacum hose unattached which there is about 4 runing all around the mastercylinder......but my guess would be the ABS ECU

May 30, 2009 | 1993 Plymouth Voyager

2 Answers

I Have a Plymouth Voyager 93 pedal brake is really hard it almost seems tha i don't have brakes help!


Does your van have ABS if it does the factory has a recall for part of this system check with your dealer they can tell you , all they need is your vin number. Also is there an ABS lite on?

Mar 15, 2009 | 1993 Plymouth Voyager

1 Answer

1993 voyager 3.3 bake & abs light on - very hard pedal


Your Brake Master Cylinder is Failing. Get this Replaced and the Brake System Bled and it will work just fine. Please Rate My Response! Thanks!

Feb 03, 2009 | 1993 Plymouth Voyager

Not finding what you are looking for?
1993 Plymouth Grand Voyager Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...