Question about Chevrolet Equinox

1 Answer

How do I get the old ones off to put new ones on.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

Old and new ones what?

Posted on Apr 02, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i install a new starter in my 2002 sebring convertible- 2.7

The person who took the old one out should put the new one in unless you are experienced in doing it. He should know what he is doing.

Feb 05, 2017 | Cars & Trucks

3 Answers

Is there a wrong way to put the thermostat in?

Yes. We all learn the hard way by installing the new one backwards. Be careful to observe as you remove the old one the corrrect way to install the new one.

Jan 10, 2015 | 2000 Jeep Grand Cherokee

1 Answer

Replace the horn

its very simple. buy a new horn n put it in the place of old one. just plug out the old one and put the new one. and connect the wires as they were connected before.

Oct 28, 2011 | 2004 Ford F150

1 Answer

Dont know where to start with placing new plug wires on my '96 360 engine.I have the firing order, but where do I start my first plug wire? Do you have a diagram ?

Take the old wires off one at a time. Compare the old wire to the new wires and find the new one that is the same length as the old one. put the new wire on routing it exactly as the old one was routed. Move on to the next wire. As long as you replace them one at a time you can't mess anything up.

Oct 08, 2010 | Dodge Ram B350 Cars & Trucks

1 Answer

How do you replace the struts on a 2006 dodge 1500 pickup?

put the front of the truck on a lift and the take out old one's with socket set and install new ones with new bushing and when installing bushings on to the strut grease them and if you have a vise it is 10 times easier, but afetr the new ones are assembled just put them on the same way you took the old ones off.

Oct 06, 2010 | 2006 Dodge Ram 1500

1 Answer

2003 dodge caravan and require two new tires on the rear. Do I plavce the new tires on the front drive axle or on the rear and move the old ones to the front

Front tires tend to wear faster than old ones. It is usually best to put the new tires on the front drive wheels (traction,steering,braking). Then put the older tires on the back.

Sep 16, 2010 | 2003 Dodge Caravan

1 Answer

Replacement of rear control arm. The control arm looks like a bar with a tie rod end and seems to be holding the wheel assembly in place. as far as I can tell it is a control arm assembly. How difficult...

It's not difficult at all. Most auto parts stores can order them, but the cheapest way to go is to go to a salvage yard. You're right, it looks like a tie rod. Disconnect the nuts, pop the old one off and bolt the new one in place. Make sure the bushings on the new one are in good shape if you pick up a used one. Otherwise just get new bushings for it before putting it in. If you have the non-adjustable control arms, it's pretty much a no brainer to pull the old one and put the new one in. There are no length adjustments to worry about. If yours are adjustable, measure from the center of one end to the center of the other on the old one, then adjust the new/used one to that length before putting it in.

May 26, 2010 | 2002 Ford Explorer

1 Answer

Is there something on the old neutral switch i need to take off and put on the new one?

there is a small cone shaped washer/gasket you must take off old one and put on new neutral switch

Jul 19, 2009 | 2000 Dodge Neon

1 Answer

Unable to remove old axel so can put new one in sure need some help

Most short shafts just require a pull. Jerking works better than pulling.

May 02, 2009 | Plymouth Voyager Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides